North Dakota Journeyman Plumber Exam Guide: The Credential, the Five-Part Examination, and the Route Between Them

North Dakota licenses its Journeyman Plumber through an examination the Board administers itself, in five parts over five hours, on the 2018 North Dakota Plumbing Code. The passing standard is 70 percent. The PassProfessor North Dakota Journeyman Plumber program prepares candidates for that written examination — its closed-book opening parts, its open-book sizing work, and the North Dakota code as the state actually adopted it.

This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.

The credential at a glance

ItemVerified position
ProgramNorth Dakota Journeyman Plumber
AdministratorBoard-administered examination — no testing vendor; no vendor bulletin exists for this credential
Code tested2018 North Dakota Plumbing Code — the 2018 Uniform Plumbing Code as adopted by NDAC 62-03.1-01-01; tested edition equals adopted edition
Code exclusionsNorth Dakota does not adopt Uniform Plumbing Code chapters 5, 12–16
Examination structure5 parts in 5 hours; Part 1 is 100 multiple-choice questions, closed book; Part 2 is a drain, waste and vent sizing completion exercise, also closed book; the remaining parts are open book and include water sizing and drain, waste and vent completion items
Passing standard70 percent for the Journeyman Plumber examination; the Master examination standard is 80 percent
Hands-on practicalNone — this examination has no hands-on practical component
RetakeA waiting period of 6 months applies before a retake
Fees (state fees)Application $50; examination $50; Journeyman Plumber license $100; renewal $100
Continuing educationContinuing education is required on a two-year cycle
SupervisionA maximum of 5 apprentices per master or journeyman per project
Administrator notePassProfessor is independent and is not affiliated with the North Dakota plumbing board or regulator

North Dakota’s system rewards candidates who read it on its own terms. There is no vendor layer to learn, no computer-based testing routine to rehearse and no gap between the code in force and the code examined. What there is, instead, is a Board-run sitting with a deliberate internal split — memory first, method second — and an adopted code that is the national model text minus the chapters the state chose not to take. This guide follows that structure: the route first, then the code, then each kind of part in depth, then the discipline of preparing for a sitting where the first hours are taken with the book closed and a failed attempt costs six months. The companion program page is the North Dakota Journeyman Plumber Exam Preparation page.

Reading the verified facts

Every fact in this guide comes from the primary-source record for North Dakota, and the guide is careful about what that record does and does not contain. Verified: the administrator, the adopted code and its rule citation, the excluded chapters, the five-part and five-hour architecture, the book status of each kind of part, the single verified part-level question count (Part 1, at 100 multiple-choice questions), the 70 percent passing standard, the absence of a hands-on practical, the 6-month retake wait, the four state fees, the two-year continuing education cycle and the supervision ceiling. Not verified, and therefore not printed anywhere in this guide: question counts for the remaining parts, per-part time limits inside the five hours, per-area blueprint weights, and any continuing education hours figure. Candidates should treat secondary sources that supply those numbers with suspicion. In a Board-administered system, the absence of a vendor bulletin means there is no vendor document for such figures to come from, and numbers without a source are a hazard to pacing and planning alike.

The route, step by step

Step one — confirm the credential and the code. The Journeyman Plumber license is the target, and the 2018 North Dakota Plumbing Code is the book. Candidates trained in another state should settle early which model code family their experience sits in, because North Dakota examines in the Uniform Plumbing Code tradition and the adjustment for International Plumbing Code-trained candidates is substantial. Step two — apply to the Board. The application fee is $50, and the route runs through the Board’s own channels from this point onward; there is no vendor registration step. Step three — sit the examination. The examination fee is $50. The sitting runs to five parts in five hours, in the order and book conditions described in this guide. Step four — meet the standard. The passing standard is 70 percent. A candidate who does not meet it waits 6 months before retaking, which is why this guide treats preparation sequencing as part of the route rather than as advice after it. Step five — license and hold. On passing, the Journeyman Plumber license fee is $100. Renewal is $100, continuing education is required on a two-year cycle, and the license carries the supervision responsibility described below — a maximum of 5 apprentices per master or journeyman per project.

The code in depth: the 2018 North Dakota Plumbing Code

The North Dakota Plumbing Code is the 2018 Uniform Plumbing Code as adopted by NDAC 62-03.1-01-01, and two features of that adoption should govern how a candidate studies. The first is alignment: because the tested edition is the adopted edition, every hour spent working in the current North Dakota code on the job is also examination preparation, and every provision learned for the sitting is a provision that governs real installations in the state. Candidates in states where the examination lags the adopted code must maintain two versions of the law in mind; North Dakota candidates maintain one, and should use the spare capacity that gives them to learn that one version thoroughly.

The second feature is subtraction. North Dakota does not adopt Uniform Plumbing Code chapters 5, 12–16. The practical consequence is that the printed national text is not the law. A candidate studying from an unmarked copy of the 2018 Uniform Plumbing Code is studying a book that contains chapters North Dakota law does not contain, and examination answers drawn from those chapters answer a question North Dakota did not ask. The disciplined approach is to mark the exclusions in the study copy from the first week — physically, so the eye learns the shape of the adopted book — and to treat any provision whose home is an excluded chapter as out of scope unless the Board’s own material says otherwise. This is the single most North Dakota-specific study act available, and generic preparation, written for states that adopt the model text whole, will never prompt it.

Within the adopted chapters, the examination’s centre of gravity is visible from its structure. Drain, waste and vent sizing is examined twice — once closed book, once open — and water sizing appears in the open-book parts, so drainage, venting and water supply method together carry more weight in the candidate’s preparation than any single memorised list. Definitions and general requirements feed the 100-question closed-book part. Materials, joints, traps, fixtures and installation rules supply the daily-work knowledge that part assumes. The guide’s study plan below sequences the work in that order: sizing method early and revisited often, core provisions built to recall, and the adopted-code shape held throughout.

Part 1 in depth: 100 questions, closed book

Part 1 is 100 multiple-choice questions taken with the book closed, and it is the part candidates most often under-prepare for, because most modern trade examinations are open book and most preparation habits assume a book on the desk. Closed-book examining changes what knowing means. A provision is known, for Part 1 purposes, when the candidate can produce its substance unprompted — the requirement, the threshold, the prohibition — and recognise the correct statement of it among close alternatives without checking. Recognition built by reading alone rarely survives that test; retrieval built by repeated self-testing does.

The working method for Part 1 is therefore distinct from the rest of the preparation. Study in short, frequent retrieval sessions rather than long reading sessions. State provisions aloud or in writing before checking them. Keep a running list of provisions missed under self-test conditions and return to that list on a shortening interval until each item is produced correctly twice in succession on separate days. Pay particular attention to the provisions a working plumber applies without thinking — clearances, slopes, trap and vent principles, material limits — because examination writers favour exactly the daily-work rules candidates assume they know, and assumption is where closed-book marks are lost. One hundred questions is a long part; pace is a skill within it. Candidates should rehearse completing multiple-choice sets at a steady rate with time held in reserve for return visits to flagged items, so that the part’s length never converts a knowledgeable candidate into a hurried one.

The sizing parts in depth: the same judgement, examined twice

Part 2 is a drain, waste and vent sizing completion exercise, and it is closed book like Part 1. The remaining parts are open book and include water sizing together with further drain, waste and vent completion items. Taken together, the sizing work is the examination’s signature: the Board examines sizing judgement in both conditions because the field demands it in both conditions. On a real project, a journeyman holds the governing method and the common values in memory well enough to lay out work and spot an undersized run on sight, and also works from the book for the full calculation, checking each branch against the tables. A candidate who can only size with the book open will find Part 2 exposes the gap; a candidate who has only memorised values without practising full book-based method will find the open-book parts slower and less accurate than they should be.

Preparation for the sizing parts therefore runs on two tracks. The closed-book track builds the method itself: the sequence of steps in a drain, waste and vent sizing exercise, the logic by which loads accumulate through a system, and the venting principles that constrain the layout, all held as procedure rather than as looked-up facts. Practise completing sizing exercises from a blank start, stating each step’s reason as it is taken, until the procedure runs without reference. The open-book track builds execution: complete sizing exercises — water sizing as well as drainage work — against the clock, with the adopted code open, until locating the governing table, reading it correctly and carrying the result forward is fast and reliable. Tabbing and organising the study copy of the code is legitimate preparation for these parts in a way it can never be for the closed-book parts, and candidates should organise the book around the sizing work: drainage, venting and water supply sections findable in seconds.

One caution applies to both tracks. Because North Dakota does not adopt Uniform Plumbing Code chapters 5, 12–16, sizing practice drawn from generic material must be checked against the adopted book before its method is internalised. A sizing routine learned from an excluded provision is worse than no routine, because it will be produced confidently. The adopted code is the only safe source for method, in the closed-book parts and the open-book parts alike.

The sitting itself

The sitting is a Board-administered event: five parts, five hours, one candidate and the Board’s papers. Candidates should expect a written examination setting rather than a vendor testing centre — no vendor check-in routine, no computer-based testing interface, and none of the small procedural surprises that vendor delivery sometimes holds for candidates who prepared on a different platform. The surprises North Dakota does hold are internal to the papers: the transition from closed-book work to open-book work partway through the sitting, and the return of sizing — the subject of Part 2 — in a second form later on.

Plan the five hours as five hours, not as a single block. Know, before entering, how the time will be divided by part as far as the verified structure allows, and hold a reserve rather than spending early parts’ time to exhaustion. The closed-book parts come first in the verified description, and they reward a rested mind; candidates who have slept, arrived early and settled before the start protect the parts where memory does the work. When the open-book parts arrive, the discipline reverses: the temptation is to look everything up, and the candidates who do well are those who look up selectively — answering from knowledge where knowledge is firm, and spending book time only where verification or a full sizing calculation genuinely requires it. There is no hands-on practical to prepare for, pace or dress for; the whole performance is written, and every hour of preparation can be spent on written performance.

A study plan built on how this examination is actually put together

Sequence the work by the examination’s own logic. First, the adopted-code map. Mark the excluded chapters, learn the adopted book’s organisation, and settle the rule citation — NDAC 62-03.1-01-01 — as the anchor for what counts as North Dakota law. Second, sizing method, closed-book track. Build drain, waste and vent sizing as internalised procedure, with water sizing method alongside it, before speed work begins. Third, core provisions to recall standard. Work the adopted chapters in retrieval sessions until the substance of daily-work rules can be produced unprompted, at the standard Part 1’s 100 questions will demand. Fourth, open-book execution. Timed sizing and completion work with the organised code open, building the lookup economy the later parts reward. Fifth, mixed full-length rehearsal. Complete sittings that reproduce the verified architecture — closed-book questions, closed-book sizing, open-book sizing and completion work in sequence, inside five hours — because the switch between conditions is itself a tested skill and only rehearsal teaches it. Throughout, keep the retake rule in view: with 6 months standing behind a failure, the plan’s purpose is a single prepared sitting, and rehearsal scores, not hope, should decide when a candidate is ready to apply that sitting.

The working method: turning the outline into a performance

There is a difference between having read the code and being able to perform it under the Board’s conditions, and the method below exists to close that gap. Sort every error by kind. Misses in this examination divide into four families: provisions not yet learned, provisions known but not retrievable under closed-book conditions, sizing procedure breaks — a step skipped or a value carried forward wrongly — and adoption errors, where an answer comes from an excluded chapter or from another code family altogether. Each family has a different cure, and study time spent on the wrong cure is wasted twice. Alternate the book conditions deliberately. Inside each study week, schedule closed-book sessions and open-book sessions as separate events with separate goals, rather than drifting between them; the sitting separates them by part, and preparation should honour the same boundary. Revisit on a lengthening interval. Material answered correctly returns after days, then weeks; sizing procedures return as complete exercises, not as re-read notes, because procedure is only verified by performance. Keep the state’s figures together. Seventy percent, five parts, five hours, 100 questions in Part 1, 6 months, 5 apprentices — the verified North Dakota numbers form a short list, and a candidate who can state the list cleanly, and say which figures are Master figures instead (80 percent, four parts), understands the system at the level the Board administers it.

The errors this examination is built to catch

North Dakota’s sitting is built to catch a recognisable set of errors. Preparing only open book is the largest: the candidate who has never practised retrieval meets Part 1 and a closed-book sizing exercise with habits formed for a different examination. Studying the unamended model text follows close behind — chapters 5, 12–16 of the Uniform Plumbing Code are not North Dakota law, and answers sourced from them fail on adoption rather than on plumbing. Importing another code family — answering Uniform Plumbing Code questions with International Plumbing Code provisions remembered from training elsewhere — fails in the same direction. Treating sizing as one skill rather than two — procedure held in memory, and execution performed from the book — leaves half the sizing work underprepared whichever half was practised. Pacing by invented numbers — per-part counts or timings from secondary sources — misallocates the five hours around figures the Board never published. And sitting speculatively, to learn the examination by taking it, is the costliest error of all in a state where the lesson costs 6 months.

After the sitting: the credential and its clock

On passing at the 70 percent standard, the candidate completes the route with the $100 Journeyman Plumber license fee and holds a credential that runs on a two-year rhythm thereafter: renewal at $100, with continuing education required on the two-year cycle. The working duties arrive immediately. The journeyman may carry up to 5 apprentices per project under the state’s ceiling — a maximum of 5 apprentices per master or journeyman per project — and the quality of those apprentices’ work, and of their formation as plumbers, rests in part on the journeyman’s direction. Candidates preparing for the Master examination in time should note its different shape now, while the comparison is instructive: four parts rather than five, and an 80 percent standard rather than 70 percent. For the journeyman, though, the clock that matters is simpler: hold the code knowledge the closed-book parts demanded, keep the sizing method sharp, meet the education cycle before renewal falls due, and the license the Board issued stays what it was on the day it was earned — the state’s statement that this plumber’s judgement can be trusted on the work and on the crew alike.

Frequently asked questions

Who administers the North Dakota Journeyman Plumber examination?

The Board administers it directly. No testing vendor is involved and no vendor bulletin exists for this credential.

What code governs the examination?

The 2018 North Dakota Plumbing Code — the 2018 Uniform Plumbing Code as adopted by NDAC 62-03.1-01-01. Tested edition and adopted edition are the same.

Which parts of the Uniform Plumbing Code does North Dakota not adopt?

Chapters 5, 12–16. Material in those chapters is not North Dakota law and is out of scope for the examination as adopted.

How many parts does the examination have, and how long does it run?

Five parts in five hours for the Journeyman Plumber examination. The Master examination runs to four parts.

Which parts are closed book and which are open book?

Part 1 — 100 multiple-choice questions — is closed book, and Part 2, a drain, waste and vent sizing completion exercise, is also closed book. The remaining parts are open book and include water sizing and drain, waste and vent completion items.

What score passes?

70 percent for the Journeyman Plumber examination. The Master standard is 80 percent.

Is there a hands-on practical or a drawing test?

There is no hands-on practical. The applied work in the examination is written sizing completion work, examined closed book in Part 2 and open book in the later parts.

How long is the wait to retake after a failure?

Six months. That wait is the reason this guide recommends sitting only when rehearsal performance shows readiness.

What does the route cost in state fees?

Application $50, examination $50, Journeyman Plumber license $100, and renewal $100.

Does North Dakota require continuing education for this license?

Yes. Continuing education is required on a two-year cycle.

How many apprentices may a journeyman supervise?

A maximum of 5 apprentices per master or journeyman per project.

Does this guide state question counts for every part?

No. Part 1’s count of 100 multiple-choice questions is verified and stated. Counts for the remaining parts are not verified in the primary record and are not printed; candidates should distrust secondary sources that supply them without a Board source.

Is PassProfessor affiliated with the Board?

No. PassProfessor is an independent preparation provider, not affiliated with the North Dakota plumbing board or regulator. The Board alone licenses and examines.

When does enrollment open for the PassProfessor program?

The program is in the works and enrollment is not yet open. Leave an email address on the companion program page and PassProfessor will write to you when the program is ready — and only about this program.