These are the exact 20 questions served in the free sample of the Water Treatment Class I Exam Prep program, in serve order, with the correct answer and a full explanation for each. The sample mixes easy, medium, hard, and stretch questions (5 / 7 / 5 / 3) drawn from this program’s own content areas.
The 20 free sample questions
1. How is chlorine demand defined for a treated water?
A. The contact time multiplied by the chlorine residual
B. The chlorine dose divided by the plant flow in MGD
C. The chlorine dosage minus the chlorine residual that remains
D. The total chlorine residual minus the free chlorine residual only
Correct: C. Chlorine demand is the portion of the dose used up reacting with substances in the water. It equals dosage minus residual, and conversely the dose needed equals demand plus the desired residual.
2. What is the main effect of short-circuiting in a sedimentation basin?
A. It increases the effective settling area without adding equipment
B. It raises the alkalinity of the water by concentrating dissolved minerals along the direct flow path to the outlet
C. It makes the sludge blanket easier to measure with a core sampler
D. It lets part of the flow reach the outlet quickly, reducing the effective detention time for that water
Correct: D. Short-circuiting means some flow takes a direct path through a basin instead of using its full volume. That portion gets less detention and less settling, lowering overall basin performance.
3. How should the SCADA network be arranged to reduce cybersecurity risk?
A. Connect it directly to the public internet for convenience
B. Put SCADA and customer billing on one open network
C. Keep it separated from general office and public networks
D. Allow any personal device to join the control network
Correct: C. Network separation is a basic SCADA cybersecurity measure, limiting who and what can reach the control system.
4. What is the static water level in a well?
A. The water level in the well when it is not being pumped
B. The water level measured only while the pump is running at full capacity
C. The depth from the pump intake to the bottom of the well
D. The total depth of casing installed below ground
Correct: A. Static level is the resting level in a non-pumping well; it is the reference point for measuring drawdown.
5. Which features protect a finished-water storage tank or clearwell from contamination?
A. Screened vents and a screened, flap-covered overflow pipe
B. Open vents and an overflow pipe left unprotected at the top
C. Unlocked hatches and lighting left off around the tank site
D. Cracked coatings and standing water pooled on the tank roof
Correct: A. Storage tanks are protected by screened vents and a screened overflow with a flap, which keep insects, birds, and debris out while still letting the tank breathe and drain.
6. How is the color of a water sample commonly measured and reported?
A. By comparison with platinum-cobalt standards, reported in color units
B. By weighing the dried residue from a filtered portion of the sample
C. By timing how long a standard light takes to pass through the sample
D. By titrating the sample with standard acid to a visible color change
Correct: A. Color, which comes mainly from dissolved organic matter, is measured by comparing the sample with platinum-cobalt standards and is reported in color units.
7. A tanker arrives with a treatment chemical delivery. What should the operator do before unloading begins?
A. Begin unloading immediately to save the driver time, without waiting for any inspection, paperwork, or label check
B. Unload first and check the paperwork next week
C. Mix the delivery into any tank with free space
D. Inspect the delivery — confirm the chemical, container condition, and labeling — before unloading
Correct: D. Deliveries are inspected before unloading so the right chemical, in sound and properly labeled containers, goes to the right place.
8. A crew will enter a vault to repair a valve. How should the ventilation blower be used?
A. Run it for one minute before entry, then shut it off so the crew can hear each other
B. Set it up to blow fresh air into the space continuously before and during the entry
C. Point it at the vault opening from across the yard so its exhaust drifts over the entry
D. Use it only after the entry, to clear the smell from the vault before the next work crew
Correct: B. Continuous forced-air ventilation supplies fresh air and dilutes hazardous gases before and throughout the entry. It runs the whole job, positioned so clean air reaches the entrants.
9. What distinguishes phenolphthalein alkalinity from total alkalinity in a titration?
A. Phenolphthalein alkalinity is measured to the first endpoint; total alkalinity continues to a lower endpoint
B. Phenolphthalein alkalinity is measured by filtration, while total alkalinity uses a colorimeter reading taken afterward
C. Total alkalinity is measured first, and phenolphthalein alkalinity is whatever remains afterward
D. The two are identical measurements that are simply reported under different names
Correct: A. Alkalinity is found by titrating with standard acid; the phenolphthalein endpoint is the first stopping point, and total alkalinity is reached by continuing to a lower endpoint.
10. In a SCADA system, what does the operator normally use to view process information and enter commands?
A. The foot valve
B. The HMI screen, which displays information from controllers such as PLCs
C. The calibration column
D. The motor nameplate only, reading the ratings stamped on the motor housing whenever needed
Correct: B. The HMI (human-machine interface) is the screen where operators view values and alarms and issue commands. PLCs carry out local automatic control and exchange data with the HMI/SCADA system.
11. During a weekly readiness check of the standby generator, what must the operator verify besides a successful start?
A. That the generator building is freshly painted
B. That the fuel tank is kept nearly empty
C. That the exhaust is blocked to reduce noise
D. That the fuel supply is checked and adequate
Correct: D. Generator readiness includes checking the fuel supply so the unit can run for an extended outage.
12. A filter with 360 sq ft of surface area receives 720,000 gpd. What is the surface loading rate?
A. 200.00 gpd/sq ft
B. 720.00 gpd/sq ft
C. 2,000.00 gpd/sq ft
D. 20,000.00 gpd/sq ft
Correct: C. Loading rate = flow / area = 720,000 gpd / 360 sq ft = 2,000.00 gpd/sq ft.
13. Before putting on a full-body harness for an entry, a worker finds cut webbing and a bent connector. What should the worker do?
A. Wear the harness anyway, since the winch line provides a second means of support too
B. Tape over the cut webbing so the damage does not catch on the edge of the wet well
C. Swap the bent connector for a carabiner from a climbing kit kept in the worker’s truck
D. Remove the harness from service and use a different, inspected harness for the entry
Correct: D. Harnesses are inspected before each use for cuts, fraying, damaged stitching, and bent or cracked hardware. Any defective harness is removed from service immediately and replaced.
14. Halfway through a shift, a turbidimeter check with a known standard reads well off its expected value. What should the operator do?
A. Continue testing as usual and simply note the observed difference in the margin of the bench sheet
B. Recheck the standard and cuvette, then recalibrate the instrument if the error is confirmed
C. Adjust all of the morning’s sample results by the size of the observed difference
D. Discard the standard, since a disagreement means the standard itself must be wrong
Correct: B. A failed verification warns that results may be wrong; the operator rechecks the standard and cuvette condition, then recalibrates if the instrument is truly off.
15. Immediately after a filter is backwashed and returned to service, its effluent turbidity is temporarily poorer before it improves. What is this period called?
A. The breakpoint period of the filter run
B. The air binding period of the filter run
C. The chloramination period of the filter run
D. The filter ripening period of the filter run
Correct: D. The ripening period right after backwash is when filter effluent quality is temporarily poorer before the bed re-establishes good removal.
16. The plant switches to a different coagulant and a new feed arrangement. What should happen to the affected standard operating procedures?
A. Leave the old SOPs in place, since operators will work out the differences on their own
B. Revise the SOPs for the new process and make sure all operators are informed and trained
C. Remove the affected SOPs from the binder so nobody follows an outdated procedure again
D. Update only the copy in the manager’s office and leave the control room copy unchanged
Correct: B. When a process changes, its written procedures must change with it — revised, dated, and communicated — so every shift works from the same current instructions, not memory or habit.
17. The same pump has needed seal repairs three times in a year. How do maintenance records most help the operator and supervisor decide what to do next?
A. They reveal the repeat-failure pattern so the underlying cause or replacement can be evaluated
B. They prove the pump should never be inspected again, so all future preventive work can be cancelled
C. They replace the need for preventive maintenance
D. They calibrate the pump automatically
Correct: A. Complete maintenance history makes repeat failures visible, supporting decisions about root-cause repair, changed preventive tasks, or replacement rather than repeated fixes.
18. A coastal wellfield increases pumping for a long dry summer and the water gradually tastes saltier. What is the most likely explanation and concern?
A. Heavy pumping is pushing freshwater out to sea and cooling the wells
B. The well screens are dissolving and releasing salt stored in the metal
C. Algae in the aquifer are producing salt as the water table keeps falling
D. Heavy pumping is drawing seawater into the aquifer toward the wells
Correct: D. Excessive coastal pumping can pull the freshwater-saltwater boundary inland. A saltier taste warns that seawater is intruding and pumping may need to be reduced.
19. Customers supplied by a lake source begin reporting earthy, musty tastes during a warm spell with visible algae growth, while routine safety results remain satisfactory. What is the most likely cause?
A. Saltwater intrusion pushing minerals into the intake zone
B. Geosmin and MIB released by algae growing in the source
C. Hydrogen sulfide gas dissolving into the lake surface water
D. Hardness minerals precipitating out in the distribution mains
Correct: B. Earthy-musty complaints during an algae bloom point to geosmin and MIB, the classic algae taste-and-odor compounds, rather than a safety failure.
20. The SCADA screen alarms for high effluent turbidity on one filter, but the operator has not yet looked at that filter. What should the operator do before changing the process based on the alarm?
A. Silence the alarm and wait to see whether it returns next shift
B. Shut down the entire plant until the SCADA system is rebooted
C. Verify the alarm against a local reading or grab sample from that filter, then act on the confirmed condition
D. Raise the coagulant dose for the whole plant based only on the screen value
Correct: C. SCADA alarms flag abnormal conditions for the operator, but instruments can drift or foul. Verifying the alarm against a local reading or sample confirms whether the filter effluent is truly high before process changes are made.
Take the sample as a timed quiz in the full program: open the free sample quiz. The full program carries 500 questions with an explanation for every answer — enroll for $49 with 6 months of access. See also the Water Treatment Class I exam guide.
Disclaimer
PassProfessor is an independent exam-preparation provider. This program is exam preparation only: it is not the real exam, it provides no education credit, and completing it does not by itself qualify you for any license or certification. The real exam is run by its own exam body — you register for it, pay its fees, and sit it through that body, not through PassProfessor. All practice questions in this program are original; they are not actual exam questions.
