Wastewater Treatment Class I Exam Prep: Free Sample Questions — The Exact 20-Question Sample, Worked

These are the exact 20 questions served in the free sample of the Wastewater Treatment Class I Exam Prep program, in serve order, with the correct answer and a full explanation for each. The sample mixes easy, medium, hard, and stretch questions (5 / 7 / 5 / 3) drawn from this program’s own content areas.

THE PROGRAM IN NUMBERS
500
PRACTICE QUESTIONS
Fresh
FULL-LENGTH PRACTICE EXAMS
Drawn new for every attempt from the full question bank
20
FREE SAMPLE QUESTIONS
Try the program before you buy
6 months
OF ACCESS
Full access from the day you enroll

The 20 free sample questions

1. What is the main purpose of aerobic digestion of wastewater sludge?

A. To convert all sludge solids directly into methane gas for plant fuel use

B. To reduce volatile solids in an aerated holding process

C. To sterilize sludge so that no further handling or disposal step is needed

D. To remove grit and screenings that were carried over from preliminary treatment

Correct: B. Aerobic digestion holds sludge under aerated conditions so microorganisms break down volatile solids, reducing the mass needing dewatering and disposal. Supernatant is returned slowly to the plant head.

2. What feature of a sludge drying bed allows liquid to drain away from the sludge?

A. A mechanical rake that turns the sludge layer every day

B. An underdrain system beneath the sand and gravel layers

C. A plastic cover stretched over the bed to keep rain off the drying sludge

D. A heating coil buried in the sand layer of the bed

Correct: B. A drying bed is built over an underdrain system bedded in gravel and sand. Water drains down through the sludge and sand into the underdrains and is returned to the plant, while the remaining moisture evaporates from the surface.

3. What is the purpose of a gravity thickener in sludge processing?

A. To destroy pathogens so the sludge can be land applied

B. To concentrate the sludge by removing water before further processing

C. To reduce volatile solids content through bacterial action

D. To dry the sludge into a stackable, truckable cake for landfill disposal

Correct: B. A gravity thickener is a settling tank for sludge: solids settle and are raked to the center while clarified water overflows. The underflow leaves more concentrated, so downstream digestion and dewatering handle less volume.

4. Which group consists entirely of chemicals used to dechlorinate wastewater effluent?

A. Alum, ferric chloride, and lime used for phosphorus removal

B. Hypochlorite, chlorine gas, and chloramine used for disinfection

C. Sodium bisulfite, sulfur dioxide, and sodium thiosulfate

D. Polymer, methanol, and caustic soda used for sludge conditioning

Correct: C. Sodium bisulfite, sulfur dioxide, and sodium thiosulfate are the dechlorination agents: each neutralizes chlorine residual before the effluent is discharged.

5. What is the main purpose of recirculating settled effluent back over a trickling filter?

A. To keep the media wetted and even out the load on the filter

B. To replace the clarifier that settles sloughed biomass from the filter effluent stream

C. To disinfect the filter effluent before it returns to the head of the treatment plant

D. To raise the temperature of the incoming wastewater during the coldest winter months

Correct: A. Recirculation returns part of the filter effluent over the media, keeping the biomass wetted, flushing excess growth, and evening out hydraulic and organic loading on the filter.

6. The SCADA screen shows a high-level alarm for a wet well, but the operator is not sure the reading is real. What is the correct response?

A. Silence the alarm and check it on the next shift

B. Reset the SCADA computer until the alarm clears

C. Verify the level at the wet well with a local check before acting on or dismissing the alarm reading

D. Assume every alarm is false until it repeats twice

Correct: C. Alarms are verified against local readings because sensors foul, drift, and fail. A quick field check confirms whether the condition is real before the operator responds.

7. Which description best matches the foam produced by Nocardia-type organisms in an activated sludge basin?

A. A bright white, billowy foam that builds up mainly when a young sludge is first being started up

B. A gray, soapy foam that appears only in the primary clarifier and disappears in the aeration basin

C. A green, algae-filled foam that forms only on pond surfaces during bright sunny afternoons in summer

D. A dark brown, thick, viscous foam that is stable and tends to trap solids on the clarifier surface

Correct: D. Nocardia-type foaming organisms produce a characteristic chocolate-brown, greasy, stable foam that resists breaking down and can carry solids onto the secondary clarifier surface.

8. A severe storm causes a power outage and rising influent flow. What guides the operators’ response?

A. Guessing based on what a neighboring plant did during a different storm event

B. Waiting without action until normal power returns on its own hours later

C. The facility emergency response plan and established standard operating procedures for outages and high flows

D. Instructions posted by visitors on the plant bulletin board during the storm

Correct: C. The emergency response plan and SOPs guide staffing, auxiliary power, bypass prevention, notifications, and documentation during events.

9. A belt press blinds quickly, cake releases poorly, and several wash-water nozzles are found plugged. What is the effect of restoring wash water?

A. Wash water dissolves polymer

B. Dry belts capture more solids

C. Wash water heats the sludge

D. Clean belts drain water better and release the pressed cake much more cleanly

Correct: D. Belt wash water keeps the belt pores open so water drains and cake releases. Plugged nozzles blind the belt, so cleaning nozzles and restoring spray restores performance.

10. Why must a positive displacement pump never be started against a closed discharge valve unless a relief valve protects the line?

A. The pump will run backward and empty the suction tank instead of filling the discharge line with chemical or sludge

B. The pump moves a fixed volume regardless of pressure, so a blocked discharge makes pressure climb until something fails

C. The pump loses prime instantly whenever the discharge valve is closed, and priming it again takes a full maintenance shift

D. The closed valve makes the pump draw air through its seals, which contaminates the chemical in the day tank beyond use

Correct: B. A positive displacement pump keeps displacing its fixed volume against a blockage, so pressure rises without limit until a relief valve opens or piping, seals, or the pump itself fail.

11. A gas chlorinator at the plant is designed to feed chlorine only while a vacuum is maintained in the system. Why is this design used?

A. If a line breaks, the vacuum is lost and the chlorine supply shuts off instead of gas escaping under pressure into the room

B. Vacuum makes the chlorine gas dissolve in water much faster than any pressure-fed system could ever manage on its own

C. Vacuum lets the operator store many more chlorine containers in the same room without adding any extra ventilation

D. Vacuum removes the need to weigh chlorine containers or to keep any records of how much chlorine the plant uses

Correct: A. Vacuum-operated chlorinators are fail-safe: any break that loses vacuum stops chlorine flow at the source, rather than letting pressurized gas escape into the room.

12. A plant wants better oxygen transfer from its existing blowers. Compared with coarse-bubble diffusers, what do fine-bubble diffusers provide?

A. Larger bubbles that rise to the surface faster in the basin

B. Airflow that needs no cleaning or inspection

C. Bubbles that only work in very shallow basins

D. Smaller bubbles with more surface area for transfer

Correct: D. Fine-bubble diffusers produce many small bubbles with far more total surface area and slower rise, so more oxygen transfers into the mixed liquor per unit of air.

13. A handheld dissolved oxygen meter reads noticeably below saturation during a calibration check. What should the operator do before trusting its aeration basin readings?

A. Increase the blower air to the basin until the meter reading rises to the expected value, since the basin is always the cause when a portable meter disagrees with what the operator expected to see

B. Average the low reading with yesterday’s reading and use that

C. Discard the meter without attempting any calibration

D. Calibrate the meter in air-saturated water following the SOP, then recheck the reading

Correct: D. DO meters are calibrated in air-saturated water per the SOP. A meter that reads low in that check must be calibrated and rechecked before its basin readings can be trusted.

14. An analyst pipettes 5 mL of a 500 mg/L stock solution into a flask and brings the total volume to 250 mL with dilution water. What concentration is the working solution?

A. 10 mg/L

B. 2,500 mg/L

C. 25 mg/L

D. 100 mg/L

Correct: A. Final concentration = C1 x V1 / V2 = 500 mg/L x 5 / 250 = 10 mg/L. Multiplying 500 x 5 without dividing by the final volume gives the 2,500 mg/L distractor.

15. An experienced operator believes a shortcut works better than the written standard operating procedure for a routine task. What is the correct approach?

A. Follow the written procedure and raise the proposed improvement through the review process so the procedure can be updated properly

B. Use the shortcut whenever supervision is not watching

C. Teach the shortcut to new operators as the preferred method, since it saves time and the written procedure will eventually catch up on its own

D. Follow the procedure only for tasks that involve chemicals

Correct: A. SOPs are followed as written; improvements go through review and revision so everyone works the same safe, approved way.

16. When a wet well is pumped down low, a swirling funnel forms over the pump suction, the pump draws air, rattles, and its capacity drops sharply. What is happening?

A. The discharge check valve is leaking, which spins the surface of the wet well into a funnel shape whenever the pump is running at full speed

B. The motor cooling fan is blowing across the water surface and pushing the wastewater into a swirl

C. Vortexing is occurring because there is too little liquid depth over the suction inlet to keep air out

D. The influent sewer is entering the wet well too slowly, so the pump is starved of solids to pump

Correct: C. A vortex forms when liquid depth over a suction inlet is too shallow. The funnel reaches the inlet and air is drawn into the pump, causing noise, vibration, and a sharp drop in capacity.

17. An equalization basin has developed odor complaints and a thick layer of settled solids on its floor while its mixers were out of service awaiting parts. What is the best corrective action?

A. Drain the basin completely and manually remove all of the settled solids

B. Restore the mixers to service so solids stay suspended and basin contents stay uniform and aerobic

C. Lower the basin level so the settled solids can dry out on the floor

D. Add chlorine solution to the basin to suppress the odors for now

Correct: B. Equalization basin mixers keep solids from settling and keep the contents uniform and aerobic. With mixing restored, accumulated solids resuspend and septic, odor-producing conditions are corrected at their source.

18. A lab result recorded for the discharge monitoring report looks far out of line with the plant’s recent performance. What should the operator do before the report is submitted?

A. Change the number to match the recent average so the report looks consistent, since a single unusual value is almost certainly a lab mistake anyway

B. Verify the result through lab records and rechecks, and report the verified value accurately rather than adjusting it

C. Leave that parameter off the report for this period

D. Submit the report late without explanation so the value is forgotten

Correct: B. Compliance reporting is built on verified, accurate data; a questionable value is checked through proper channels, never altered to fit expectations.

19. A biological phosphorus removal plant’s effluent phosphorus climbs after an operator reroutes a nitrate-rich recycle stream into the anaerobic zone. What went wrong?

A. The anaerobic zone organisms used the extra nitrate to store too much phosphorus

B. The recycle stream cooled the anaerobic zone below its working temperature range

C. Nitrate entering the anaerobic zone destroys the oxygen-free conditions phosphorus release requires

D. The extra flow washed all of the phosphorus-accumulating organisms out of the plant entirely

Correct: C. Biological phosphorus removal depends on a truly anaerobic zone, with no oxygen or nitrate present, so organisms release phosphorus there and over-absorb it later. Feeding nitrate into that zone breaks the conditions the process needs.

20. Thick brown foam is building up on the aeration basin and is being trapped on the secondary clarifier, where trapped solids are starting to go over the weirs. A well-meaning suggestion is to hose the foam back into the mixed liquor. What is the better practice?

A. Remove the foam from the surface for disposal with the waste sludge instead of returning the foaming organisms to the basin

B. Hose the foam back in, because diluting the foaming organisms in the mixed liquor weakens them until they die off

C. Skim the foam off and spread it on the primary clarifier, where the scraper can push it into the primary sludge line for further treatment there

D. Spray the foam with basin effluent until it breaks apart, then let the pieces settle out again in the clarifier

Correct: A. The foam is concentrated with the very organisms causing the problem. Returning it reseeds the basin, while physically removing it with wasting steadily reduces their numbers.

Take the sample as a timed quiz in the full program: open the free sample quiz. The full program carries 500 questions with an explanation for every answer — enroll for $49 with 6 months of access. See also the Wastewater Treatment Class I exam guide.

Disclaimer

PassProfessor is an independent exam-preparation provider. This program is exam preparation only: it is not the real exam, it provides no education credit, and completing it does not by itself qualify you for any license or certification. The real exam is run by its own exam body — you register for it, pay its fees, and sit it through that body, not through PassProfessor. All practice questions in this program are original; they are not actual exam questions.