Wastewater Collection Class III Exam Prep FREE Sample Exam

Maintenance logs for one pump show repeated overload trips spread over months, each reset and returned to service, while the station’s other pump never trips. What does that logged pattern most directly indicate?

A recurring mechanical or load problem on that pump, not random events

Correct Incorrect Correct answer

Proof that the overload device itself should be removed from the circuit

Correct Incorrect Correct answer

A level sensor reading higher than the true wet well level

Correct Incorrect Correct answer

Normal operation that needs no program attention at any point

Correct Incorrect Correct answer

After a pump rehabilitation, a duty check measures flow in a force main section with a flow area of 1.45 square feet and a velocity of 3.7 feet per second. What is the flow through the section?

5.37 gpm

Correct Incorrect Correct answer

1,203.91 gpm

Correct Incorrect Correct answer

4,815.62 gpm

Correct Incorrect Correct answer

2,407.81 gpm

Correct Incorrect Correct answer

A manager is setting CCTV inspection frequencies for a new program covering both large trunk sewers and small residential lines. What principle should set the frequencies?

Residential lines are inspected most often because they are shortest, while trunk lines wait the longest

Correct Incorrect Correct answer

Every line in the system is inspected on the same fixed cycle, regardless of size, age, or consequence

Correct Incorrect Correct answer

Only lines that have already overflowed are inspected, and all other lines wait until a problem is reported

Correct Incorrect Correct answer

Trunk and high-consequence lines are inspected most often, with longer cycles for low-risk local lines

Correct Incorrect Correct answer

Why does a preventive program schedule periodic pigging of a force main that is still flowing without complaint?

To pressure-test the main to destruction so weak points reveal themselves during the run and can be marked for later repair

Correct Incorrect Correct answer

To flush the main backward toward the station wet well

Correct Incorrect Correct answer

To give a new crew practice inserting equipment into a live line

Correct Incorrect Correct answer

To wipe wall buildup away before it narrows the main and cuts its capacity

Correct Incorrect Correct answer

Before a reach is moved to a longer cleaning cycle, its supervisor verifies carrying velocity. The reach carries 7.6 cubic feet per second through a flow area of 2.0 square feet. What is the velocity?

15.2 ft/s

Correct Incorrect Correct answer

3.8 ft/s

Correct Incorrect Correct answer

0.26 ft/s

Correct Incorrect Correct answer

5.6 ft/s

Correct Incorrect Correct answer

What is the main program reason structure inspections use a standard set of defect codes rather than free-form descriptions?

Free-form descriptions are prohibited in the field because writing narrative notes during an inspection is unsafe

Correct Incorrect Correct answer

Standard codes make condition data comparable across crews, structures, and years, so trends and priorities can be built from it

Correct Incorrect Correct answer

Standard codes are shorter to type, and saving keystrokes is the primary reason the coding system was adopted

Correct Incorrect Correct answer

Standard codes allow the inspection to be completed without actually observing the defect being recorded

Correct Incorrect Correct answer

Discharge pressures at one station have crept upward at unchanged flow over several years, suggesting the force main’s interior is roughening or narrowing. Before funding a full cleaning program, what evidence should the manager require?

Vendor assurances that cleaning always restores at least half of lost capacity

Correct Incorrect Correct answer

A single pressure reading taken on the day the contractor visits

Correct Incorrect Correct answer

The age of the main alone, since old mains always benefit equally

Correct Incorrect Correct answer

A pilot cleaning judged by before-and-after measurements

Correct Incorrect Correct answer

Storage between control levels matters at a small neighborhood station. Its round wet well measures 5 feet across; how many gallons are stored in 7 feet of its depth?

About 1,027.6 gallons

Correct Incorrect Correct answer

About 822 gallons

Correct Incorrect Correct answer

About 1,336.5 gallons

Correct Incorrect Correct answer

About 1,542 gallons

Correct Incorrect Correct answer

In long-term defect analysis, a capacity defect is distinguished from a condition defect by which difference?

A capacity defect appears only in summer, while a condition defect appears only in winter, a distinction based on the season in which the defect was first noticed by a maintenance crew

Correct Incorrect Correct answer

A capacity defect means sound pipe is being asked to carry more flow than it can, while a condition defect means the pipe itself has deteriorated

Correct Incorrect Correct answer

A capacity defect is found by flow meters, while a condition defect can never be detected by any instrument

Correct Incorrect Correct answer

A capacity defect requires no action, while a condition defect always requires emergency repair

Correct Incorrect Correct answer

Evening solvent odors recur at one trunk junction, but routine daytime samples there are always clean. The program adds a conductivity-triggered automatic sampler at the junction. What does this design accomplish that the old program could not?

It guarantees the discharger will be identified by name from the sample alone, without any upstream tracing work by the field crews

Correct Incorrect Correct answer

It captures the discharge while it is passing, at whatever hour it occurs, instead of sampling the junction only when it runs clean

Correct Incorrect Correct answer

It prevents the discharge from occurring, because automatic samplers deter dischargers who learn that a sampler is present

Correct Incorrect Correct answer

It replaces the need for any field response to odor complaints at that junction for the rest of the program year

Correct Incorrect Correct answer

The utility buys its first units of a new type of inspection equipment. No maintenance procedure exists for it. What must the manager’s new procedure include to be complete at the program level?

Only the manufacturer's warranty terms, so crews know which repairs the vendor will pay for during the term of coverage

Correct Incorrect Correct answer

Only a cleaning schedule, because inspection electronics rarely need any other scheduled care or checking

Correct Incorrect Correct answer

Only the purchase price and delivery date, filed with the equipment record for future replacement planning

Correct Incorrect Correct answer

Scheduled tasks and intervals, required parts and calibration, safety precautions, and the records to be kept

Correct Incorrect Correct answer

Year-to-date reports show lift station power costs running well above budget while flows are near normal. What is the manager’s best response?

Ignore the variance until year end, since power bills are outside the program's control entirely

Correct Incorrect Correct answer

Order crews to run stations less often, even if wet-well levels rise above normal operating ranges

Correct Incorrect Correct answer

Transfer money from the training budget without documenting the change or its effect on the program or on staffing, schedules, or the service levels the program is expected to maintain

Correct Incorrect Correct answer

Investigate the cause, forecast the year-end impact, and adjust the budget plan through proper channels

Correct Incorrect Correct answer

Wastewater Collection Class III Exam Prep FREE Sample Exam — Fixed Set

Quiz Summary

Information

Results

Results

Categories

1. Question

2. Question

3. Question

4. Question

5. Question

6. Question

7. Question

8. Question

9. Question

10. Question

11. Question

12. Question

Programs

Company

Legal

Account