North Carolina Plumbing Contractor Class I (P-I) and Class II (P-II) Exam Guide: The Two-Part Sitting, the 2018 State Code, and the Contractor Route

North Carolina licenses plumbing at the contractor tier. The State Board of Examiners of Plumbing, Heating and Fire Sprinkler Contractors examines Plumbing Contractor Class I (P-I) and Plumbing Contractor Class II (P-II) candidates in two parts — a Technical part of 4.0 hours and a Business and Law part of 1.5 hours — tested on the 2018 North Carolina Plumbing Code, and its rule requires a grade of 70 of 100 on each part. This guide sets out the full route, from the experience filing to the December renewal.

This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.

The credential at a glance

ItemVerified position
ProgramNorth Carolina Plumbing Contractor Class I (P-I) and Class II (P-II): both contractor classes in one program
RegulatorState Board of Examiners of Plumbing, Heating and Fire Sprinkler Contractors (G.S. Chapter 87, Article 2; rules at 21 NCAC 50)
Examination vendorPSI Services LLC (PSI), under contract to the Board
Examination structureTwo parts, both required: a Technical part and a Business and Law part
Examination timeTechnical part 4.0 hours; Business and Law part 1.5 hours — the same for Class I and Class II
Passing standardA grade of 70 of 100, on each part, as the Board’s rule at 21 NCAC 50 .0305 provides
Book statusOpen book, with candidate-supplied references from the list for the candidate’s approved category
Tested code2018 North Carolina Plumbing Code (built on the 2015 International Plumbing Code, as amended by North Carolina)
Practical componentNone is published for these examinations
Administrator notePassProfessor is independent and is not affiliated with the State Board of Examiners of Plumbing, Heating and Fire Sprinkler Contractors

The companion program page is at /north-carolina-master-plumber-exam-prep/. This guide goes deeper: the Board, the two classes, the qualification gate, the book rules, and every branch after the sitting — pass, partial pass, failure, renewal, lapse, and reinstatement.

Start with the title: there is no master licence here

The most consequential fact about North Carolina plumbing licensure is a negative one. North Carolina has no credential titled Master Plumber, and no statewide journeyman plumber license or examination — the Board’s own examination categories contain no such category at all.

What the Board issues at the contracting tier is the Plumbing Contractor license, in two classes. Class I (P-I) covers potable water and drain, waste and vent piping systems in any building — residential, commercial, or industrial. Class II (P-II) covers the same systems in single-family detached dwellings only.

North Carolina also issues restricted contractor licenses within the same tier family and a separate set of technician licenses. A Plumbing Technician has passed the technical examination but not the business law examination, so a technician license is not a contracting license; this guide returns to that pathway in the consequences of a partial result. The Technician classes are not part of this program.

The Board and its legal frame

The regulator is the State Board of Examiners of Plumbing, Heating and Fire Sprinkler Contractors: seven members appointed by the Governor — drawn from engineering education, city inspection, the licensed plumbing, heating, air conditioning and fire sprinkler trades, and a public member with no tie to the construction industry — serving seven-year terms. Its statutory home is G.S. Chapter 87, Article 2 (§§ 87-16 through 87-27.1), and its rules sit at 21 NCAC 50.

That frame matters practically: operative examination facts live in the Board’s rules as much as in any vendor bulletin — the passing standard, set out below, is a rule figure — and candidates who look only at vendor material will miss facts the Board publishes in its own layer.

The two-part structure, in full

A contractor candidate sits two parts: a Technical part and a Business and Law part, and every contractor examinee must pass both. The durations come from the Board’s Examination Listing and Information: Class I (P-I): Technical 4.0 hours; Business and Law 1.5 hours. Class II (P-II): Technical 4.0 hours; Business and Law 1.5 hours.

The identity of those durations is itself information: Class II is not a shorter examination for a smaller license, but the same sitting pointed at a narrower scope. (Within the same tier family, the Restricted Limited Plumbing Contractor sits a Technical part of 2.0 hours with the same 1.5-hour Business and Law part.)

No content outlines are published in any source read for this guide: the Board and PSI publish the structure, durations, reference lists, and administration rules, but no weighted blueprint for the Technical part. Treat any source offering a precise topical split with suspicion, and prepare across the whole of the tested code.

The Business and Law part is recorded here for structure only. Its reference is Business & Project Management for Contractors, 6th or 7th edition (NASCLA), Board edition, and its content is a separate body of material from the technical code work this program teaches. One exemption is structural: the Business and Law part is not required if the applicant holds a currently active contractor license with this Board and passed the Board’s Business and Law examination after August 2003.

The passing standard, in the rule’s form

The passing standard is verified from the Board’s rule — not from the PSI bulletin, which publishes no pass score. 21 NCAC 50 .0305 provides that Board examinations are based on a maximum obtainable grade of 100 points, and a grade of 70 of 100 is required to pass. That requirement applies to each part of a multi-part examination.

Hold the standard in exactly that form. There is no averaging across the sitting: a candidate can clear the Technical part and still leave without a contractor license because the Business and Law part fell short — and that exact result has a defined consequence in this system, set out below. Scores at the sitting are reported immediately as PASS/FAIL.

The tested code: 2018, state-amended, and still governing

All plumbing, heating, fuel piping and fire sprinkler examinations are currently based on the 2018 editions of the North Carolina codes. For plumbing, the tested book is the 2018 North Carolina Plumbing Code (2018 NCPC), based on the 2015 International Plumbing Code, as amended by North Carolina, effective January 1, 2019. North Carolina maintains its own state plumbing code, so the examination reference is the state code book — not the national International Plumbing Code by itself. The North Carolina amendments are part of the tested text, and a provision that reads one way in the national model may read differently in the state book.

The adopted layer currently coincides with the tested layer: the 2018 North Carolina Building Code, including the plumbing code, is the enforced layer in the sources, from the same January 1, 2019 date.

The later edition requires the guide’s clearest statement. The 2024 North Carolina State Building Code is not in effect and must not be keyed. Its effective date has been postponed repeatedly, and the Board’s June 1, 2026 update states the position in substance: until the 2024 code takes effect, all plumbing, heating, fuel piping, and fire sprinkler examinations are based on the 2018 codes. This guide states no 2024 effective date as settled, because none is settled. A candidate who prepares from a 2024 edition is preparing from a book the examination does not use, on the strength of a date nobody has fixed.

The Board’s allowed-reference list works in lettered codes: A 2018 Administration Code and Policies, B 2018 Plumbing Code, C 2018 Fuel Gas Code, D 2018 Mechanical Code, E 2018 Energy Conservation Code, F 2018 Residential Code, G Board’s Laws & Rules (2025 or 2026 edition), H Business & Project Management for Contractors (6th or 7th edition). Both contractor classes are anchored to the 2018 codes, including the plumbing code; candidates take into the room only the books listed for their approved category.

Open book, strictly policed

The examinations are open book with candidate-supplied references: candidates must bring all of their own reference materials, manuals, and codebooks. What is provided at the site — pencils, scratch paper, calculators, and the North Carolina Heating and Plumbing Figures — must all be returned. The condition rules for the books are detailed, and every one is enforced at the door:

  • Only the books listed for the candidate’s approved license category are allowed.
  • Books must be hard-bound, spiral-bound, or ring-bound, in original published condition.
  • Highlighting is the only alteration allowed.
  • Commercially available permanent tabs are allowed; the only approved loose-leaf full-page inserts are ICC “Turbo Tabs.”
  • No writing, underlining, notes, or formulae may appear in the books, before or during the examination.
  • Printed PDF versions are not allowed.

The consequences of arriving wrong are stated in advance: a candidate who arrives with unauthorized materials or devices is not allowed to test, must wait 90 days before rescheduling, and the materials are confiscated and forwarded to the Board. Preparation therefore includes a physical audit of the book set — bindings, tabs, inserts, and a check that no stray notation has crept into a borrowed copy.

Inside the room, a pre-exam tutorial of up to 15 minutes does not count against examination time, and some questions are based on field experience and trade practice, not limited to the listed references. The figures booklet supports figure-based items within the written sitting; it does not convert any part of the examination into a drawing test. No practical component is published: no primary source publishes any hands-on practical, drawing, or isometric component for any North Carolina plumbing examination.

Qualifying to sit: experience, filing, and the background report

Plumbing Contractor Class I and Class II examination eligibility requires two years (4,000 hours) of on-site full-time experience in the installation, maintenance, service, or repair of plumbing systems related to the category sought, whether or not a license was required for the work. The statute caps what the Board may require at two years, with up to one-half permitted as academic or technical courses, and registration is not required at commencement.

The academic substitution is quantified: up to 2,000 hours may be directly related academic or technical training, stated as 45 quarter hours or 30 semester hours, with each approved semester hour converting to 66.66 hours of experience credit; the Board prorates part-time work and part-time academic work. A licensee who has continuously maintained a license in good standing for a minimum of 10 years is accepted as having the experience for Class II qualifications. An applicant may also be required to establish that they are at least 18 years old and of good moral character.

The application runs to a long list of components, including an experience description with hours and type, notarized employer experience verification, a signed criminal-background-check authorization, a signed SSA-89, and disclosure of criminal charges and convictions. Every contractor examination applicant must obtain a nationwide criminal background record report through CastleBranch.com, pay the provider, and include a printed copy; a report more than six months old must be updated for re-examination. Experience from other states may be submitted; Certified Code Enforcement Official experience does not meet the requirements, and neither do certificates in fields not directly related.

Fees, kept in their layers

Application layer. The application for license by examination is $150 in total — a $75 application fee plus a $75 examination fee — under the Board’s rule as amended effective June 1, 2026, and it is nonrefundable; the Board’s FAQ states the same $150 fee. The examination-fee component is collected through PSI and is part of the $150, not an addition to it. The license fee must then be paid within 45 days of notification of the examination result, or the candidate must retest; a person who obtains a license by passing an examination on or after October 1 may receive it for the remainder of that year by paying one-half the usual license fee.

Licensing and renewal layer. Annual license and renewal fees set by rule: plumbing, heating, and fuel piping contractor licenses are $150; a second or subsequent qualifier listed on a firm license is $75; a technician listed under a licensed contractor is $75; the Restricted Limited Plumbing Contractor license is $150; an inspector-status licensee is $25.

Smaller Board fees. License copy $20; abstract of a license record $25 per search; copy of the Board’s rules $10; license reissue or transfer $25; initial application for a license without Board examination $30; criminal-history predetermination petition $45; and a late renewal processing fee of $25, applying when renewal is not received correctly before January 31.

Sitting day and the result

The Board approves the application first; processing currently averages about six weeks. The candidate then registers with PSI and must take the examination within 90 days of the Board’s eligibility notification. Examinations are computer-based and delivered daily at seven North Carolina PSI centers: Asheville, Charlotte, Fayetteville, Greenville, Raleigh, Wilmington, and Winston-Salem. Out-of-state PSI testing may be allowed. Scores are reported immediately as PASS/FAIL.

Failing a part: the 90-day rule and the banked pass

A candidate who fails any part is not reexamined until after 90 days from the date last examined, and must submit a Re-Examination Application. The failed portion may be retaken within 6 months of the approval date without retaking the passed portion — the wait is 90 days, the banked pass lasts 6 months, and a candidate who lets the window close retakes more than the failed part. The Board may require an applicant who fails any part three times to receive additional education or wait one year before retaking. A failing candidate may, on written request, review the examination at a Board-set time and place.

The partial-result pathway is distinctive. An applicant who fails only the business portion of a Class I examination but passes the technical portion may request a Class I Technician license based on the technical pass; the parallel route runs from Class II to a Class II Technician license. In the other direction, a holder of an active Plumbing Technician license obtained by examination may obtain the Contractor license in the same category and class by meeting the contractor experience requirement and passing only the business portion. The two parts are therefore genuinely separable assets: a technical pass can be held as a technician license and later converted by completing the business portion alone.

Recognition from other states

North Carolina’s position is restrictive. North Carolina has no reciprocity agreements with any other state. The Board may in its discretion license an out-of-state contractor without written examination on satisfactory proof of substantially equivalent qualifications — a discretion, not an entitlement. One agreement operates on a defined slice: a South Carolina Technical Examination Waiver Agreement applies only to the technical section — its mappings include South Carolina Commercial Mechanical and Plumbing credentials toward Plumbing Class I, and South Carolina Residential Plumbing toward Plumbing Class II — and the North Carolina business section must still be taken and passed. Under the Neighbor State License Recognition Act, current permanent residents licensed in Georgia, South Carolina, Tennessee, Virginia, or West Virginia may be eligible for equivalent licensure.

Renewal, lapse, and the continuing education answer

All licenses expire on the last day of December each year following issuance or renewal. There is no grace period: all licensed activities must cease until the license is renewed. The renewal period begins 90 days before expiration, usually October 1, and the late renewal processing fee of $25 applies when renewal is not received correctly before January 31.

The continuing education answer is plain and frequently disbelieved: North Carolina has no continuing-education requirement for renewal. The requirement as a condition of renewal was eliminated December 31, 2012, and the former rules were repealed the same date; the statute still authorises the Board to adopt such rules, but none is in force. What replaced the mandate, from January 1, 2013, is disciplinary education — Board-ordered courses imposed on complaint. That is a sanction, not a renewal duty; the Board separately encourages voluntary continuing education.

Reinstatement has a hard outer edge. An expired license may be reinstated within three years of expiration on written request with payment of the current license fee, the fees for the unpaid prior years, and the processing fee. The Board requires reexamination when a licensee fails to renew within three years, and a license expired more than three years cannot be renewed at all. December discipline is therefore the difference between a renewal, a paid reinstatement, and starting again at the examination.

A study plan built on how this sitting is actually put together

Sequence the work by the sitting’s real structure. First, the tested book: work in the 2018 North Carolina Plumbing Code itself, and learn where the state amendments change the model text — those changes are exactly what a state-book examination can ask and model-code preparation cannot answer. Second, book craft: practise finding provisions fast, in the physical books that will pass the door check, with permanent tabs placed where the work recurs. Third, the experience items: revisit the judgement calls of your 4,000 hours rather than treating experience as a filing requirement only. Fourth, the second part’s structure: schedule Business and Law preparation as a separate block with its own reference book. Fifth, the calendar: work backwards from Board processing averaging about six weeks, 90 days to sit after eligibility notification, 90 days after any failure, and 6 months of life in a passed part.

The errors this examination is built to catch

Studying the wrong book is the largest: the national model code without the North Carolina amendments, or a 2024 edition for a sitting that remains on 2018. Misnaming the credential signals a candidate working from another state’s map. Treating the parts as averaged fails the each-part grade. Arriving with a non-compliant book — loose inserts, handwritten notes, a printed PDF, a removable tab — ends the day before it starts and adds a 90-day wait. Letting the 45-day license-fee deadline lapse after a pass converts success into a retest. Assuming a grace period exists after December risks unlicensed activity, because none does.

North Carolina in one view

North Carolina is a contractor-tier state with a two-part gate. There is no master title and no journeyman rung; there are two contractor classes divided by a single scope line — any building, against single-family detached dwellings only — examined identically at 4.0 hours technical and 1.5 hours business and law, graded at 70 of 100 on each part under the Board’s own rule, in an open-book room where the candidate’s own state code book is both the permitted tool and a compliance test in itself. Around the sitting sit the distinctive mechanics: a 4,000-hour experience gate with a quantified academic substitution, a 90-day wait after failure against a 6-month banked pass, a technician license that gives a lone technical pass somewhere to live, a December expiry with no grace period, and no continuing education owed at renewal at all.

The PassProfessor program page for this credential is at /north-carolina-master-plumber-exam-prep/, with the notify form for enrollment.

Frequently asked questions

Does North Carolina license Master Plumbers or Journeyman Plumbers?

No. North Carolina has no credential titled Master Plumber and no statewide journeyman plumber license or examination. The contractor tier is Plumbing Contractor Class I (P-I) and Plumbing Contractor Class II (P-II).

What distinguishes Class I from Class II?

Scope only. Class I covers potable water and drain, waste and vent systems in any building; Class II covers the same systems in single-family detached dwellings only. Durations and the passing standard are the same for both classes.

How is the examination structured?

Two parts, both required: a Technical part of 4.0 hours and a Business and Law part of 1.5 hours, for both classes, administered by computer through PSI after Board approval.

What is the passing standard, exactly?

A grade of 70 of 100, on each part — the form in which the Board’s rule at 21 NCAC 50 .0305 states it. The PSI bulletin publishes no pass score; the verified source is the Board’s rule.

Which code should I study?

The 2018 North Carolina Plumbing Code — the 2015 International Plumbing Code as amended by North Carolina. The state code book, not the national model alone, is the examination reference.

Has the examination moved to the 2024 code?

No. The 2024 North Carolina code is not in effect, and examinations remain on the 2018 codes. No effective date for a change is stated as settled in this guide, because none has been set.

What books may I bring, and in what condition?

Only the books listed for your approved category, supplied by you: bound in original published condition, highlighting the only alteration allowed, permanent tabs allowed, no writing or notes, and no printed PDF versions.

Is there a practical examination?

No practical, drawing, or isometric component is published for any North Carolina plumbing examination. The published format is a written, computer-based examination.

How much experience must I show?

Two years — 4,000 hours — of on-site full-time experience related to the category sought, with up to one-half permitted as directly related academic or technical training (45 quarter hours or 30 semester hours; 66.66 hours of credit per approved semester hour).

What does it cost to apply?

$150 in total — a $75 application fee plus a $75 examination fee — nonrefundable. The license fee must be paid within 45 days of notification of the result or the candidate must retest.

If I fail one part, what happens?

You are not reexamined until after 90 days, on a Re-Examination Application. The failed portion may be retaken within 6 months of the approval date without retaking the passed portion. After three failures of any part, the Board may require additional education or a one-year wait. Failing candidates may also request an examination review.

What is the technician pathway?

An applicant who passes the technical portion but fails only the business portion may request a Technician license in the same class based on the technical pass — not a contracting license, but one whose holder may later obtain the Contractor license in the same class by meeting the experience requirement and passing only the business portion. The Technician classes are not part of this program.

Can I transfer a licence from another state?

North Carolina has no reciprocity agreements with any other state. A South Carolina technical examination waiver applies only to the technical section, and the North Carolina business section must still be taken and passed.

When does the licence expire, and is there a grace period?

All licenses expire on the last day of December, with no grace period; licensed activities must cease until renewal. Reinstatement is available within three years; beyond three years the license cannot be renewed and reexamination is required.

How much continuing education does renewal require?

None. The requirement was eliminated December 31, 2012, and the former rules were repealed the same date. Board-ordered disciplinary education is a separate mechanism, not a renewal duty.

Is PassProfessor affiliated with the Board or PSI?

No. PassProfessor is an independent preparation provider, not affiliated with the Board or with PSI. The Board alone licenses, and candidates apply through the Board and register through PSI.

When does enrollment open for the PassProfessor program?

The program is in the works and enrollment is not yet open. Leave an email address on this page or on the program page at /north-carolina-master-plumber-exam-prep/ and PassProfessor will write to you when the program is ready — and only about this program.