Tennessee CMC-C HVAC, Refrigeration & Gas Piping Exam Guide: The Specialty, the Two Sittings, and the Dated Book Transition

Tennessee’s CMC-C classification — HVAC, Refrigeration, Gas Piping — is a specialty contractor license held by a business and earned by its Qualifying Agent through two Prov examinations: a 100-question trade paper in 300 minutes and a 50-question Business and Law paper, each open book and each published at 73% to pass. This guide works through the credential in the order a candidate actually meets it: what the specialty covers, who is examined, what each paper contains, which books govern which dates, and what the license then authorises.

This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.

The credential at a glance

ItemVerified position
ProgramTennessee CMC-C HVAC, Refrigeration & Gas Piping (Qualifying Agent examinations)
RegulatorTennessee Board for Licensing Contractors (Department of Commerce and Insurance), under T.C.A. Title 62, Chapter 6
Credential holderThe business; the Qualifying Agent is the examined individual
VendorProv, Inc., the Board’s examination provider since July 1, 2026; Candidate Information Bulletin v1.6, effective October 31, 2026
Trade examinationCMC-C: 100 questions / 300 minutes / open book, computer-administered
Business examinationTennessee Contractor Business and Law: 50 questions / 150 minutes, required of every first-time contractor licensee
Tested editionInternational Mechanical Code 2021 on the permanent reference list; a limited-time reference block runs through December 31, 2026
Passing standard73% to pass — the only published form; no raw count is published
Fees, by layerProv: $53.00 per examination. Board: application and initial license $250; renewal $200 per 2 years
DeliveryComputer-based at six Tennessee Prov centres or any Prov centre, or remote via Examroom.ai; no Board pre-approval for CMC-C
Administrator notePassProfessor is independent and is not affiliated with the Tennessee Board for Licensing Contractors

The companion program page is at /tennessee-cmc-c-hvac-refrigeration-gas-piping-exam-prep/. This guide is the deeper document: it separates the layers Tennessee candidates most often merge — business and individual, specialty and full mechanical license, trade paper and business paper, permanent books and dated books, tested code and adopted code, vendor fee and Board fee — and treats each on its own terms.

Reading Tennessee correctly: five separations

Business and individual. The license belongs to the business entity; the examination belongs to its Qualifying Agent. Most Tennessee errors begin by collapsing those into one person holding one personal title.

Specialty and major. A major classification carries its specialties with it automatically. A specialty license, standing alone, authorises only that specialty. CMC-C is complete inside heating, cooling, refrigeration, and HVAC-related gas piping — and silent outside them.

Vendor eras. Prov has administered the Board’s examinations since July 1, 2026, and the current Prov bulletin controls every mechanic on this page. Material describing the prior vendor’s era describes a superseded examination, except where the current bulletin itself carries a reference forward inside its dated limited-time block.

Permanent and dated books. The reference list is two lists with two different lifespans, and a candidate who treats them as one list will prepare with books that expire mid-route.

Tested and adopted. The examination’s code edition and the state’s adopted code edition are separate layers that happen to agree at 2021 in this cycle. Agreement is not identity: the bulletin governs the sitting, the adoption rule governs the field.

What CMC-C covers — and what it leaves to other classifications

The rule names the classification HVAC, Refrigeration, Gas Piping, specialty C under MC (CMC) — Mechanical Contracting. The bulletin’s scope sentence covers the installation, alteration, repair, replacement, and servicing of heating, ventilation, air conditioning, refrigeration, gas piping related to HVAC equipment, and associated mechanical systems, including comfort heating and cooling systems, refrigeration equipment, ventilation systems, ductwork, exhaust systems, controls, heat pumps, geothermal and solar thermal HVAC systems, and related refrigeration piping.

Three boundary readings matter. First, the gas piping inside CMC-C is gas piping related to HVAC equipment — not a general gas-fitting licence standing alone. Second, the refrigeration inside CMC-C is the equipment-and-piping refrigeration of the heating and cooling trade. Third, the full CMC is a different and wider credential: its Appendix A range runs A through J across plumbing, process piping, sprinklers, boilers, fuel gas, pollution control, and temperature controls. A candidate who needs that range needs the full mechanical route, with its own pre-approval and examination. Nothing in this guide borrows the full CMC’s content.

Two structural rules complete the scope picture. The CMC notation on licenses issued after 1992 represents that the licensee passed the Board licensing examination, and no county or municipality may require such a licensee or its employees to pass a county or municipal test. And the license itself is thresholded: a contractor license is required before bidding or offering a price for projects of $25,000 and up including materials and labour, and subcontractors performing mechanical or HVAC work must be licensed as contractors when their portion reaches $25,000.

The Qualifying Agent: who sits, and what the role demands afterwards

The Qualifying Agent is the person who must obtain a successful score in the classification and meet the Board’s Qualifying Agent requirements. The permitted relationships are defined by business form: a sole proprietorship’s owner, or a full-time employee holding written power of attorney; a partnership’s general partner, or such an employee; a corporation’s major stockholder — owning at least 20 percent of the stock — or such an employee; a limited liability company’s manager or member, or such an employee. The pattern is consistent: the examined mind must genuinely belong to the business.

The role is policed after licensure. If the person who took the examination leaves the firm, the firm must designate an individual to take the examination within three months; the Board must be notified within ten days of a Qualifying Agent’s death, resignation, termination, or incapacity; and if no replacement is appointed within three months, the license becomes inactive — potentially mid-contract. A Qualifying Agent for a first-time applicant must pass the trade examination within 90 days.

One gate CMC-C candidates do not face deserves equal emphasis: Board pre-approval is not required for CMC-C. Pre-approval attaches to mechanical plumbing — the full CMC and CMC-A. The CMC-C candidate schedules directly with Prov under the certifying body “TN — Tennessee Board for Licensing Contractors,” at provexam.com.

On experience, the Board’s own application material must be quoted at its own strength. The Board records that it looks at experience — it prefers 3 years — and at equipment and financial information when granting a classification. Its classification decisions primarily consider adequate experience in the classifications requested, an established plant, and the necessary equipment and experience to operate it. That is a preference weighed with other factors. No provision retrieved states a fixed minimum-years rule for CMC-C, and this guide states none: not as a hurdle to clear, and not as a hurdle that does not exist in some other form. Expect experience to be weighed; do not convert the preference into a statute.

The application package itself runs through CORE, the state’s online licensing system, with a Board-stated processing time of four to six weeks. It carries a written application with affidavit, evidence of current workers’ compensation insurance — an applicant is ineligible until it is provided — an affidavit affirming general liability and workers’ compensation insurance with amounts, a letter of reference from a past client, employer, or codes administration official, and a financial statement.

The trade examination, block by block

The CMC-C trade examination is a single computer-administered, open-book sitting: 100 questions, 300 minutes, 73% to pass, $53.00 to Prov. Its published outline, which sums exactly to 100, rewards close reading:

  • Air Distribution and Venting — 23. The dominant block. Duct systems, air movement, and venting reasoning carry nearly a quarter of the paper, reflecting a specialty in which moving conditioned air correctly is the daily work.
  • Piping — 14. The second block: the piping work that connects equipment, including refrigeration piping within the specialty’s scope.
  • Fuel Gas Systems — 10. A tenth of the paper, matching the gas piping element in the classification’s name.
  • HVAC Equipment — 10. The equipment itself: selection, installation, and servicing knowledge across the comfort systems the scope sentence lists, heat pumps and geothermal and solar thermal systems among them.
  • Refrigerants and Oils — 10. The refrigeration tenth: refrigerant behaviour, oils, and the handling knowledge the refrigeration element demands.
  • General Knowledge — 9. The trade’s shared foundation.
  • OSHA Safety — 6. Construction safety as its own scored block.
  • HVAC Controls — 5 and Load Calculations — 5. Control reasoning and sizing arithmetic, each a twentieth of the paper.
  • Code Requirements — 4. Direct code application, beyond the code knowledge embedded in every other block.
  • Electrical Concepts — 2 and Fire and Smoke Protection — 2. Small blocks, still scored.

The study implication is mechanical: allocate time roughly as the bulletin allocates questions. A preparation plan that spends equal weeks on all twelve blocks underprepares the 23-question block by design. Equally, the small blocks are cheap questions to lose through neglect — two questions on fire and smoke protection are two questions.

The companion Tennessee Contractor Business and Law examination is a separate sitting: 50 questions, 150 minutes, 73% to pass, open book, $53.00, required of every first-time contractor licensee. Its outline: Estimating and Bidding 7; Contracts 6; Business Organization 4; Project Management 4; Risk Management 4; Licensing 5; OSHA Safety 5; Labor Law 5; Tax Law 5; Financial Management 3; Lien Law 2 — summing to 50. Its sole reference is the NASCLA Contractors Guide to Business, Law and Project Management — Tennessee, 4th edition, 2024. A candidate taking both examinations sits 150 scored questions across two separate Prov registrations; no combined price is published by either the bulletin or the rules, and none is printed here.

The passing standard, stated once and correctly

Both examinations publish the same standard in the same short form: 73% to pass. No longer verbatim sentence is quoted for CMC-C in the sources, and no raw number of correct questions is published for either sitting. This guide manufactures neither. A candidate pacing a practice sitting should pace against time and coverage, not against an invented raw threshold.

Books, editions, and the December 31 line

The permanent CMC-C reference list — the books permitted on and after January 1, 2027 — is: the International Mechanical Code 2021; Modern Refrigeration and Air Conditioning, 21st edition; Refrigeration and Air Conditioning Technology, 9th edition; the Residential Comfort System Installation Standards Manual, 8th edition (SMACNA); OSHA 29 CFR 1926; and HVAC Basics for Contractors, 4th edition. Note what the permanent list does not contain: no standalone electrical reference, no candidate-supplied ACCA manual set, no duct-construction standard of its own. The list is the list.

The limited-time block — headed in the bulletin as open book usable for a limited time — holds the Manual J Workbook (2016), printed as available at the testing site and distributed by the proctor before the examination starts; the International Fuel Gas Code, 2021; the Pipefitters Handbook, 3rd edition; the HVAC Duct Construction Standards (SMACNA); Ugly’s Electrical References; and the Carrier System Design Manual Part 3 — Piping Design. The general grace note runs with it: from July 1, 2026 through December 31, 2026, a candidate may use any reference manual the prior vendor recommended for that specific examination; on January 1, 2027 and thereafter, only books recommended by Prov will be permitted. What changes on that date is therefore complete: the six limited-time titles cease to be permitted, any other prior-vendor reference used under the grace note ceases with them, and the permanent list alone remains.

This guide records one feature of that arrangement without resolving it, because the sources do not resolve it: for CMC-C, the fuel gas code appears inside the limited-time block, while Fuel Gas Systems is a published 10-question block of the examination. Nothing here states that the fuel gas code remains available to CMC-C candidates after 2026, and nothing states that it is removed from the examination’s life after 2026. Candidates testing across the turn of the year should confirm their book list against the Prov bulletin current at their sitting, and should build their fuel gas knowledge on the International Fuel Gas Code 2021 substance either way — knowledge does not expire with a book list.

In the adopted layer, kept separate as it must be: effective August 17, 2025, Tennessee adopted the 2021 editions of the International Mechanical Code and the International Fuel Gas Code, among other state codes, while the residential code remains an earlier edition. The examination’s 2021 mechanical edition therefore matches current state adoption — no edition gap — but local editions vary, since a locally adopted model code generally may be no more than seven years older than the latest published edition, and this guide asserts no single local edition statewide. Federal EPA Section 608 technician certification, finally, is a separate federal credential and a separate PassProfessor program; no source retrieved makes it a condition of this Tennessee license, and it plays no part in this route.

Money, stated by layer

Vendor layer. Prov charges $53.00 per examination — the trade sitting and the Business and Law sitting are separate registrations at that fee. The rule frame is that the examination fee is the fee charged by the administering entity, subject to Board approval.

Board layer. The application and initial license fee is $250, non-refundable, paid with the online application. The renewal fee is $200. Smaller Board charges exist at the same layer — transfer and duplicate-certificate fees among them — and belong to the Board’s fee rule, not to the examination. Vendor dollars and Board dollars are never one sum, and any single “cost of getting licensed” figure that merges them misstates both.

Financial layer. The initial financial statement discipline is tiered: a requested limit of $3,000,000 or less requires a reviewed or audited CPA statement prepared under generally accepted accounting principles; above $3,000,000, an audited statement; compiled and income-tax-basis statements are not acceptable. At renewal, a limit of $1,500,000 or less may rest on a self-prepared balance sheet with a notarised statement, while above that a CPA compilation is the minimum. Since July 1, 2026, a qualifying surety bond of at least 50 percent of the requested monetary limitation may be submitted in lieu of a financial statement, on the Board-approved form, continuous in form — $250,000 of bond behind a $500,000 limit, $750,000 behind $1,500,000, $1,500,000 behind $3,000,000 or an unlimited limit — and if the bond ceases to be in effect, the license becomes invalid. That instrument is distinct from the older Contractor’s License Bond, which is supplemental indemnity only; the Board’s financial guidance stresses the two forms are not interchangeable.

The monetary limitation: the license’s second number

Every Tennessee contractor license carries a monetary limitation per classification, stated on the certificate, and exceeding it is unlicensed activity as to the excess. It is a per-project cap, not an aggregate-volume cap. The general rule is the lesser of 10 times net worth or 10 times working capital; an unlimited license is discretionary where the applicant demonstrates minimum working capital and net worth of $300,000 or more; a 10 percent tolerance over the limit applies; limits for different classifications on one license may not be combined; and a project may not be split to avoid the limit.

The bidding rules interact with it. A contractor may bid a contract requiring work in another classification only if it holds a commercial building contractor’s license, or its license permits it to perform at least 60 percent of the bid amount; and it may not actually perform more than $25,000 of work in any classification it is not licensed in. General liability minimums at renewal are keyed to the limit the business carries: $100,000 of coverage at a limit up to $500,000; $500,000 up to $1,500,000; $1,000,000 above $1,500,000 — with the certificate naming the Tennessee Board for Licensing Contractors as certificate holder. The monetary limitation is not back-office detail: it decides which work the business may lawfully take, and it is set by the same financial record the application assembles.

Holding the license: renewal, lateness, and the education absence

The license expires on the last day of the twenty-fourth month following issuance or renewal — a two-year cycle. Renewal notices are mailed 90 days before expiration; renewal must be received 30 days before expiration, with the financial statement, a bankruptcy report, the renewal fee, and evidence of current workers’ compensation coverage. Lateness is priced by formula: the renewal fee increases 10 percent for each month or fraction of a month of delay, capped at twice the normal fee. A contractor in default for one year must make a fresh application. A licensee may also retire the license on the Board’s form — $25 to retire, $25 yearly to maintain retired status, reinstatement without examination, and no more than seven years retired.

On continuing education, this guide states an absence exactly as an absence: no continuing education is required to renew a mechanical contractor license in any provision of the Contractors Licensing Act part, the Board’s rules, the Prov bulletin, or the Board’s renewal form as retrieved. The only contractor continuing education in the Tennessee scheme is the eight hours of Residential Continuing Education owed by the listed residential classifications, attained by the Qualifying Agent and reported at renewal. A CMC-C licensee who also holds a residential classification owes those hours for the residential classification — the duty attaches there, not to CMC-C. Out-of-state licensure, finally, confers no right to work in Tennessee: Tennessee’s reciprocal agreements provide a trade examination waiver only; the applicant must still obtain the Tennessee license, file the full application, and pass the Tennessee Business and Law examination.

Sitting day and after: delivery, results, retakes

Prov delivers the examinations by computer at six Tennessee centres — Chattanooga, Greeneville, Knoxville, Memphis, Murfreesboro, and Nashville — at any other Prov centre in the United States, and remotely at home through Examroom.ai. Registration runs through the Prov scheduler under the certifying body “TN — Tennessee Board for Licensing Contractors.” Prov grades the examination immediately upon completion and forwards results to the licensing authority. Rescheduling or cancelling is free at least 3 days before the date; missing that deadline, or the appointment itself, forfeits the fee.

The retake discipline is short and permissive: no limit on the number of attempts; a candidate who does not pass must wait 1 day before retesting; and a candidate cannot retake an examination once passed unless the licensing authority requires it. No waiting period or attempt cap from any earlier era applies to these sittings, whatever older preparation material may say. The sourced examination is a written examination administered by computer; no hands-on, practical, or drawing component is stated in any source retrieved, and this guide claims neither its presence nor a verified absence beyond that record. As of September 17, 2026, the Department no longer mails physical license certificates; licensees access and print their license within CORE.

Errors this guide exists to prevent

Preparing from the prior vendor’s era. Its fees, formats, and book lists are void for these sittings; the Prov bulletin controls. Treating the dated book block as permanent — or discarding fuel gas study because a book’s listing is dated: the 10-question Fuel Gas Systems block is published. Reading “prefers 3 years” as a gate and self-excluding. Skipping the Business and Law sitting because the trade paper felt like the whole route. Waiting for pre-approval that CMC-C does not require, while missing the 90-day pass window. Merging the dollars — vendor fee, Board fee, bond, and financial statement are four different instruments. Ignoring the monetary limitation until a bid exceeds it.

Tennessee CMC-C in one view

Tennessee CMC-C in one view is a specialty examined at business scale: a business holds the license, a Qualifying Agent earns it, two Prov sittings at 73% to pass stand in the way, air distribution carries nearly a quarter of the trade paper, the book list turns on a December 31 date, and the license that results is sized by a monetary limitation computed from the business’s own financial record. The candidate who internalises that design — specialty first, two sittings, permanent books, layered dollars — is studying the credential Tennessee actually issues. The companion program page at /tennessee-cmc-c-hvac-refrigeration-gas-piping-exam-prep/ describes the PassProfessor program built on that design.

Tell me when enrollment opens. This program is in the works and enrollment is not yet open. Leave an email address and PassProfessor will write to you when it is ready — and only about this program.

Frequently asked questions

Is CMC-C the same as the full CMC?

No. CMC-C is the specialty classification HVAC, Refrigeration, Gas Piping. The full CMC is the major mechanical classification whose range runs A through J; holding the major includes the specialties, while holding the specialty alone authorises that specialty only.

How many examinations, and what are their mechanics?

Two for a first-time licensee: the CMC-C trade examination (100 questions, 300 minutes, open book) and the Tennessee Contractor Business and Law examination (50 questions, 150 minutes, open book), each a separate Prov registration at $53.00.

What is the passing standard, exactly as published?

73% to pass, for both examinations. No raw number of correct questions is published, and this guide manufactures none.

Which code edition is tested?

The International Mechanical Code 2021 sits on the permanent reference list. In the adopted layer, Tennessee adopted the 2021 mechanical and fuel gas editions effective August 17, 2025; local editions vary.

What happens to the limited-time books?

They are usable only through December 31, 2026. On January 1, 2027 and thereafter, only books recommended by Prov are permitted, and the permanent list alone remains.

Does the fuel gas code stay in the examination after 2026?

This guide states neither outcome. The bulletin places the International Fuel Gas Code 2021 in the CMC-C limited-time block, and Fuel Gas Systems is a published 10-question block. Confirm the current bulletin at your sitting and study the 2021 fuel gas substance either way.

Do I need Board pre-approval, or three years of experience?

Neither as a gate. Pre-approval attaches to the full CMC and CMC-A, not CMC-C. The Board states a preference for 3 years of experience, weighed with equipment and financial information — a preference, not a fixed minimum.

What does it cost, layer by layer?

Prov charges $53.00 per examination. The Board’s application and initial license fee is $250 and renewal is $200 per 2 years. The layers are separate and are never published as one combined examination price.

If I fail, how soon can I sit again?

Attempts are unlimited, with a 1-day wait after a failure. An examination once passed cannot be retaken unless the licensing authority requires it. Rescheduling is free at least 3 days ahead.

Does CMC-C renewal require continuing education?

Tennessee requires Residential Continuing Education only for the listed residential classifications. No continuing education duty attaches to this mechanical specialty in the provisions retrieved.

Is PassProfessor affiliated with the Board or Prov?

No. PassProfessor is an independent preparation provider. The Board alone licenses, and Prov administers the examinations.

When does enrollment open for the PassProfessor program?

The program is in the works and enrollment is not yet open. Leave an email address on this page and PassProfessor will write to you when the program is ready — and only about this program.