North Carolina Heating Group H3 Exam Guide: The Statutory Sentence, the Unpublished Counts, and the Route to the License

North Carolina licenses Heating Group No. 3 Contractor work through the State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors. Heating, group number three is a direct heating or cooling system that raises or lowers the temperature of a space for comfort, with a mechanical refrigeration capacity of 15 tons or less — and it includes systems in single-family residences regardless of size. This guide works through the credential in the order the Board built it: definition first, then the examination as published, then the license in use.

This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.

The credential at a glance

ItemVerified position
ProgramNorth Carolina Heating Group H3 — the Heating Group No. 3 Contractor license, Class I and Class II
RegulatorState Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors, 1109 Dresser Court, Raleigh, NC 27609
Statutory scopeG.S. 87-21(a)(4): a direct heating or cooling system with mechanical refrigeration capacity of 15 tons or less
Examination structureTwo parts, both required: a technical part and a Business and Law part (structure only in this guide)
Examination timeTechnical part: 4.0 hours. Business and Law part: 1.5 hours
Book statusOpen book — candidate-supplied approved references only
Passing standardA grade of 70 of 100, on each part (21 NCAC 50 .0305)
Tested codes2018 North Carolina codes, built on a 2015 International Code basis
Administrator notePassProfessor is independent and is not affiliated with the State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors

The companion program page is at /north-carolina-heating-group-h3-exam-prep/. Where that page summarises, this guide slows down: the full statutory sentence is taken apart element by element, the examination is described only in the terms the Board and PSI actually publish, and the operating rules that will govern an H3 contractor’s residential work are stated from the Board’s own rules.

The definition, element by element

“Heating” is the umbrella: heating group number one, heating group number two, heating group number three, or any combination thereof (G.S. 87-21(a)(7)). The third group’s own definition, at G.S. 87-21(a)(4), is a direct heating or cooling system of a building that raises or lowers the temperature of the space within the building for comfort, in which electric heating elements or products of combustion exchange heat either directly with the building supply air or indirectly through a heat exchanger using an air distribution system of ducts, and having a mechanical refrigeration capacity of 15 tons or less.

Direct. The system’s defining act is an exchange of heat with the building supply air. That exchange may be direct — the air itself passes over the heating element or through the combustion heat source’s immediate path as the statute phrases it — or indirect, through a heat exchanger, provided the delivery into the space runs through an air distribution system of ducts. Either way, air is the delivery medium into the occupied space. A system whose delivery medium into the space is water or steam is a different statutory animal.

The single-family inclusion. Standing outside the sentence but attached to it in the Board’s record: systems installed in single-family residences are included under heating group number three, regardless of size (G.S. 87-21(a)(3)). The inclusion overrides the ceiling for one building type only. It is the reason a candidate cannot classify by tonnage alone, and it is treated in its own section below.

Classes: one license, two territories

The Board establishes two classes for its licenses (G.S. 87-21(b)(1)): Class I, covering plumbing, heating, and fire sprinkler systems for all structures, and Class II, covering plumbing and heating systems in single-family detached residential dwellings. For this group the Board’s plain language gives the working pair: H3-I is a forced-air heating and cooling system with cooling capacity of 15 tons or less in any building; H3-II is the same in single-family detached dwellings only.

Class I and Class II do not change the examination’s time, its passing standard, or its book status. They change scope — where the holder may work — and, for some groups, the reference set. An applicant’s class decision is therefore a business decision made before the examination, not an examination decision: the contractor who will serve only detached houses can hold the narrower territory honestly, and the contractor whose work will cross into other buildings needs the wider one. Holding the narrower class and contracting beyond it is contracting outside the license held, which the Board’s rules prohibit.

The residence rule and the rule that states the reach

21 NCAC 50 .0501(b) is the rule a working H3 contractor will cite most often, because it states the license’s reach in work terms: the installation of heating and air conditioning systems or components located in single-family dwellings, and systems of 15 tons or less capacity in non-residential structures, require a Heating Group 3 license — except where heat is provided by hot water or steam in a Heating Group 1 system, or cooling is provided by a unitary appliance such as a window unit, in which case a license is not required on that point.

The equipment rule in full

21 NCAC 50 .0508(a) requires a license in heating, group No. 3 for the installation or replacement of a furnace, air handler, heat pump, package unit, ductwork, or condenser in a heating, group No. 3 system. Paragraphs (b) and (c) add two installations candidates frequently underestimate. An H3 license is required to install or replace a self-contained fireplace unit if the unit utilises ducts or a blower to distribute air to areas not immediately adjacent to the fireplace itself — the distribution, not the hearth, is what brings the job into the rule. And an H3 license is required when air conditioning of 15 tons or less is added to an already installed Heating Group 3 system — the retrofit job, not only the original installation.

The neighbours, held distinct

Group 1 is wet heat. Heating, group number one is the heating system of a building which requires the use of high or low pressure steam, vapor or hot water, including all piping, ducts, and mechanical equipment appurtenant thereto, within, adjacent to or connected with a building, for comfort heating (G.S. 87-21(a)(2)). The Board’s own plain language calls it the “wet,” water-based group: H1-I in any building, H1-II in single-family detached dwellings only. A license in heating, group No. 1 is required for the installation or replacement of a boiler in a Heating Group 1 system (21 NCAC 50 .0507). The wet/dry contrast is the Board’s own outline language, and it is the only form in which this guide uses it: Group 1 carries heat in water and steam; Groups 2 and 3 move conditioned air.

Group 2 is the same air side, above the line. Heating, group number two is an integral system for heating or cooling a building, an assemblage of interacting components producing conditioned air, having a mechanical refrigeration capacity in excess of 15 tons, and which circulates air (G.S. 87-21(a)(3)). Multiple units serving interconnected space and aggregating more than 15 tons are included in Group 2 systems, whether or not separately ducted or controlled (21 NCAC 50 .0501(a)), and a Group 2 license is required for installation or replacement of equipment or ductwork in such a system, unless exempted by the single-family provision (.0508(d)). The air-side groups are divided solely by that capacity line, plus the single-family inclusion that routes residences to Group 3 at any size. No other distinction between them is stated in the sources, and this guide invents none.

Eligibility: experience, age, character, and the application package

The experience gate is Rule .0306(b): an applicant for a heating examination shall present evidence, when submitting the application, of two years of full-time experience in the installation, maintenance, service, or repair of plumbing or heating systems related to the category for which a license is sought, whether or not a license was required for the work performed. Up to one-half may be academic or technical training related to the field. The Board’s outline states the working form: 2 years — 4,000 hours — of on-site full-time experience in the category sought, with up to one-half, stated as 45 quarter hours or 30 semester hours, as directly related academic or technical training, and with experience hours from other states submittable. The statute caps the whole requirement: experience required may not exceed two years, up to one-half may be academic or technical courses, and registration is not required at the commencement of the experience period (G.S. 87-21(b)(3)). Certified Code Enforcement Official experience does not meet the requirement, and neither do certificates in engineering or any other field not directly related to the license applied for.

The examination, described only as published

The examinations are administered by PSI, computer-based at seven PSI sites: Asheville, Charlotte, Winston-Salem, Raleigh, Fayetteville, Greenville, and Wilmington. The score — pass or fail — is given immediately at the centre. The bulletin of record is the PSI Candidate Information Bulletin for these contractor examinations, updated August 25, 2026.

Each person examined for a contractor license must pass both the business and law part and the technical part of the examination required by G.S. 87-21(b) (21 NCAC 50 .0301(b)). The three Heating Groups share one format; only the technical content and references differ by group. This guide treats the Business and Law part as structure only: a required part of 1.5 hours, carrying the same passing standard, with one exemption — it is not required if the applicant holds a currently active contractor license with this Board and passed the Board’s Business and Law examination after August 2003. No Business and Law subject content is built in this package.

The technical part runs 4.0 hours. The statute describes the examination’s design: it ascertains the applicant’s technical and practical knowledge concerning analysis of plans and specifications, estimating costs, fundamentals of installation and design, codes, fire hazards, and related subjects as they pertain to the system category (G.S. 87-21(b)(3)). That is knowledge language describing a written examination’s subjects. No hands-on practical, drawing, or performance component for this examination is stated in the sources behind this guide, and no verified statement that none exists is stated either; the sitting as sourced is the two-part computer-based examination described in this section, and this guide presents it in exactly those terms.

The unpublished counts: a discipline, not a gap to fill

This guide now states, deliberately and in full, what it will not state. A count of items for the H3 Technical examination is not published. A count of items for the Business and Law examination is not published. No pretest, experimental, or unscored count for either examination is published. Those negatives rest on the whole primary record pulled for this license: the current PSI bulletin states no per-examination count and says nothing about pretest or unscored items for these examinations; 21 NCAC 50 section .0300 states none; the Board’s examination information and applicant information state none.

That discipline protects candidates twice over. First, pacing: a candidate who has rehearsed against a duration — 4.0 hours, book in hand — has rehearsed against something real, while a candidate pacing against an invented count has built a plan on air. Second, trust: preparation material that prints a count the Board never published is telling the candidate, on its first factual page, that it will decorate where it does not know. This program’s position is the Board’s position: the counts are unpublished, full stop. If the Board or PSI publishes them in a future primary document, this guide’s successor will print them with that citation; until then the honest sentence is the one in this section.

Book status: the open-book room

Both parts are open book, restricted to candidate-supplied approved references. Only the books for the approved license category are allowed in the room. References must be original editions in hard, spiral, or ring binding; printed PDFs are not allowed. Commercially available permanent tabs are allowed. Highlighting is the only permitted alteration — notes, formulae, and underlining may not be added. Pencils, scratch paper, calculators, and the North Carolina Heating and Plumbing Figures are provided at the site and must be returned. A candidate who arrives with unauthorised materials or devices is not allowed to test and must wait 90 days before rescheduling.

The passing standard, in the rule’s words

21 NCAC 50 .0305, Passing Grade, provides: “Examinations provided by the Board are based upon a maximum obtainable grade of 100 points, and a grade of 70 is required to pass.” With Rule .0301(b), the standard is a grade of 70 of 100, on each part: the technical part and the Business and Law part are passed separately, and neither compensates for the other.

Codes and references: the 2018 layer in detail

The Board’s Book Reference List and Requirements, effective July 1, 2025, keys the examinations as follows. A — North Carolina Administration Code and Policies, 2018 Edition. C — North Carolina Fuel Gas Code, 2018 Edition. D — North Carolina Mechanical Code, 2018 Edition. E — North Carolina Energy Conservation Code, 2018 Edition. F — North Carolina Residential Code, 2018 Edition. G — the Board’s Laws and Rules, 2025 or 2026 Edition, comprising G.S. 87 Article 2 and 21 NCAC 50. H — Business and Project Management for Contractors, 6th or 7th Edition in the NASCLA North Carolina plumbing, heating, and sprinkler edition, recorded here as the Business and Law part’s listed reference, as structure only. I — ACCA Manual CS (1993). J — Manual J, 8th Edition version 2. K — Manual N, 5th Edition. L — Manual Q (1990). M — Manual D, 3rd Edition, Volume 1. O — Modern Refrigeration and Air Conditioning, 22nd Edition; the 21st Edition was allowed only until June 30, 2025. R — the ACCA Duct Calculator slide rule, which each heating and cooling candidate furnishes themselves. One plumbing-code letter sits in the Board’s list for plumbing classes; it is not part of this license’s set and is noted here only so the lettering reads whole.

Per the reference matrix, this group’s Class I set carries the Manual J, Manual N, and Manual D references together with Modern Refrigeration and Air Conditioning; the Class II set is reduced. Preparation material must key each item’s citation to the matrix row for the exact group and class, because the sets genuinely differ across groups and classes.

The Board’s update of June 1, 2026 confirms the basis in one sentence: until further codes become effective, all examinations for plumbing, heating, fuel piping, and fire sprinkler licensing will be based on the 2018 edition of the codes.

The field layer is separate and is stated separately. The 2018 North Carolina Mechanical Code is based on the 2015 International Mechanical Code, effective January 1, 2019, with Building Code Council amendments from December 2017 through December 2022, including identified North Carolina errata, that revise, delete, or add to it. The 2018 North Carolina Codes, effective January 1, 2019, include the 2018 North Carolina Ad-Hoc Committee amendments along with the 2015 International Codes, following availability during a transition period from July 1, 2018 through December 31, 2018. The 2018 North Carolina Fuel Gas Code carries that title as adopted by the North Carolina Building Code Council on June 13, 2017, effective January 1, 2019; in that code, references to the International Codes mean the North Carolina Codes, and North Carolina amendments are underlined in the published text, and its scope sections cover fuel-gas piping systems, fuel gas appliances, gaseous hydrogen systems, and related accessories on the terms stated there. In the field, the North Carolina Building Code as adopted by the Building Code Council is the minimum standard of competence for Board licensees, who shall design and install systems meeting or exceeding the minimum standards of the State Building Code, manufacturer’s specifications and installation instructions, and prevailing industry standards (21 NCAC 50 .0505(b)).

Fees, in three separate layers

Board layer. The application for a license by examination requires a fee of $150, consisting of a $75 application fee and a $75 examination fee, which is nonrefundable (21 NCAC 50 .1101(c)). Application fees are not refunded (Rule .0307).

Vendor layer. The PSI examination fee is $75, charged through PSI and valid for one year from payment. It is a different fee from the Board’s $150 above. The fact base behind this guide directs that the two never be conflated, and this guide never presents them as one charge, a combined total for the route, or interchangeable names for the same instrument.

License layer. The annual license fee for a plumbing, heating, and fuel piping contractor license is $150 (21 NCAC 50 .1102(a); G.S. 87-22 provides that the annual license fee for such contracting shall not exceed $150). On passing, that fee, with the License Activation Form, is due within 45 days of notification of the result (Rule .1101(c)); a passing applicant who does not complete activation within 45 days will have to retest. A person who passes on or after October 1 may elect a license for the following year, and by statute a license for the remainder of the year costs one-half of the usual license fee.

Renewal, late renewal, reinstatement

All licenses expire on the last day of December in each year following issuance or renewal (G.S. 87-22); the license is renewed annually, and every Board license expires December 31. Renewal notice must be sent at least one month in advance of expiration; invoices are mailed in early October, email notices are also sent, and a licensee who does not receive an invoice or notice is still responsible for renewing. The renewal period begins 90 days before expiration, usually October 1.

Retakes and rescheduling

A person who fails any examination shall not be reexamined until after 90 days from the date last examined; an applicant who fails may take the failed portion within six months of the date approved to take the examination without retaking the portion passed; and the Board may require applicants who fail any part three times to receive additional education before retaking, or to wait one year before retaking any portion (G.S. 87-21(b)(6)). In Board process, failing applicants wait 90 days and submit a Re-Examination Application; retest paperwork in the same classification is that application and the examination fee, with an updated criminal background report required if the report on file is more than six months old. A failing applicant may attend an examination review in Raleigh before retesting and may, on written request, review the examination at a time and place determined by the Board (21 NCAC 50 .0308). Rescheduling runs on a shorter, separate clock: if PSI is contacted at least three days in advance, the examination may be rescheduled at no additional charge; otherwise the examination fee is forfeited. The Board’s 90-day retake rule governs reexamination; no shorter vendor scheduling line displaces it, and none is stated as governing anywhere in this guide.

Reciprocity, stated in its layers

The Board’s applicant information states that there are no license reciprocity agreements with any other state, and that all persons desiring licensure with this Board must meet the Board’s requirements and satisfactorily complete the applicable examinations. Alongside that statement sit a rule providing reciprocity only pursuant to agreements worked out after mutual review (21 NCAC 50 .0310), a statute giving the Board discretion to grant an equivalent license without written examination on satisfactory proof of substantially equivalent qualifications (G.S. 87-21(g)), a Technical Examination Waiver Agreement with South Carolina — whose applicants must still pass the North Carolina business law examination — and the Neighbor State License Recognition Act for current permanent North Carolina residents licensed in Georgia, South Carolina, Tennessee, Virginia, or West Virginia. The layers are not merged here; the prudent applicant plans on this Board’s requirements unless a specific published route clearly applies.

Operating the license: locations, supervision, design duties

The design and installation duties are written close to this group’s work. Every newly installed residential heating and air conditioning system shall be designed and installed to maintain a maximum temperature differential of 4 degrees Fahrenheit room-to-room and floor-to-floor, with a separate system per floor or automatically controlled zoning per level on multilevel structures (Rule .0505(d)). All licensed contractors and technicians in this field shall perform a room-by-room load calculation for all newly installed residential structures before installing, with the written record provided on request and kept in the job file a minimum of six years (Rule .0505(e)). For replacement of a furnace, condenser, package unit, or air handler in an existing residential system, a minimum of a whole-house block load calculation is required, on the same record and retention terms (Rule .0505(f)). Those three paragraphs are, in effect, the H3 contractor’s daily standard of practice, and they explain why the load-calculation references sit on this license’s book list.

Refrigeration contractor licensing sits outside this Board entirely, with a separate state board under 21 NCAC 60; no refrigeration-contractor figure or rule belongs in preparation for this license beyond that boundary sentence.

A study plan that follows the guide’s order

Frequently asked questions

What are Class I and Class II for this license?

Class I covers heating systems for all structures; Class II covers heating systems in single-family detached residential dwellings. The class changes scope, not examination time, passing standard, or book status.

Why does the single-family inclusion matter so much?

Because it removes the size limit for one building type: systems in single-family residences are included under this group regardless of size, while non-residential systems are included at 15 tons or less.

What installations require the H3 license?

Installation or replacement of a furnace, air handler, heat pump, package unit, ductwork, or condenser in a Group 3 system; ducted or blower-distributing self-contained fireplace units; and added cooling of 15 tons or less to an installed Group 3 system (21 NCAC 50 .0508).

What must be passed, and to what standard?

Both parts — technical and Business and Law — each to a grade of 70 of 100 (21 NCAC 50 .0305), subject to the Business and Law exemption for a qualifying active Board contractor licensee.

How long does each part run?

The technical part runs 4.0 hours; the Business and Law part runs 1.5 hours. Both are open book with approved references only.

Which references govern the sitting?

The Board’s Book Reference List effective July 1, 2025: the 2018 North Carolina codes, the Board’s Laws and Rules 2025 or 2026 edition, and the ACCA, refrigeration, and duct-calculator references listed in this guide, per the matrix row for the candidate’s group and class.

Are the 2024 North Carolina codes tested?

No. The 2024 North Carolina code is not in effect and is not the examination basis. All examinations for this Board remain based on the 2018 editions until further codes become effective.

Is PassProfessor part of the Board?

No. PassProfessor is an independent preparation provider, not affiliated with the State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors or with PSI. The companion program page is at /north-carolina-heating-group-h3-exam-prep/.

When does enrollment open?

The program is in the works and enrollment is not yet open. Leave an email address on this page and PassProfessor will write to you when the program is ready — and only about this program.