Massachusetts Journeyperson Sheet Metal Exam Guide: The Class Family, Three Outlines, One Open-Book Standard

Massachusetts journeyperson sheet metal licensure is governed by the Board of Examiners of Sheet Metal Workers under Massachusetts General Laws Chapter 112, Sections 237 through 251, and 271 CMR. The tier comprises Class J-1 Unrestricted β€” examined in a general form and a Metal Roofing form, each 80 questions in 150 minutes β€” and Class J-2 Restricted, at 60 questions in 120 minutes, all open book under the Board’s PSI candidate bulletin updated May 1, 2024, and all passed at a minimum of 70% correct. The program page is at /massachusetts-journeyperson-sheet-metal-exam-prep/.

This program is part of the expanding PassProfessor catalog β€” join the notify list and we’ll email you when enrollment opens.

The credential at a glance

ItemVerified position
ProgramMassachusetts Journeyperson Sheet Metal: Class J-1 (Unrestricted) and Class J-2 (Restricted), 271 CMR 3.01(2)
RegulatorBoard of Examiners of Sheet Metal Workers, Division of Occupational Licensure (M.G.L. c. 112, Β§Β§ 237–251)
ExaminationsThree: J-1 Unrestricted (80 questions, 150 minutes); J-1 Metal Roofing (80, 150); J-2 Restricted (60, 120) β€” all open book, administered by PSI
Passing standardBulletin: “A passing score is a MINIMUM of 70% correct” (271 CMR requires a passing score and prints no percentage)
PretestFive to ten pretest questions may be added; unscored, their time excluded from examination time
EligibilityJ-1: 8,000 apprentice hours over no less than five years plus a 750-hour Board-approved course. J-2: 4,800 hours plus 450 hours over no less than three years
Fees$155 to the Commonwealth with the application; $180 to PSI upon approval; renewal $80 β€” never merged
Term and CETwo-year term expiring on the 28th day of the birth month; no continuing education currently required

This guide is built as a matrix and read as one. The journeyperson tier is not a single license with a single examination but a small family β€” two classes, three examinations, three outlines, two shelves and two gates β€” administered under one bulletin and one passing standard. Nearly every error available here is a blending error: J-2 figures carried into a J-1 application, the Roofing shelf carried into the general sitting, the field code carried into the examination room, or the Commonwealth’s fee carried into the vendor’s. The guide’s method is therefore separation. PassProfessor is independent and is not affiliated with the Board of Examiners of Sheet Metal Workers or PSI.

The framework: Board, statute and regulation

The Board of Examiners of Sheet Metal Workers sits within the Division of Occupational Licensure. It determines eligibility for admission to examinations, conducts examinations, and licenses qualified individuals at the journeyperson and master levels, on a restricted and unrestricted basis β€” with administration contracted to PSI Exams, which schedules and conducts the sittings for approved applicants. The Board was established by M.G.L. c. 13, Β§ 101, under the Acts of 2008, Chapter 232. Its substantive statute is M.G.L. c. 112, Β§Β§ 237 through 251: Β§ 237 supplies the definitions; Β§ 240 directs the Board to examine each applicant as to his practical knowledge of sheet metal work; and Β§ 244 empowers the Board to adopt continuing education rules. The regulation family, 271 CMR, runs from 1.00 to 9.00: definitions at 2.00, licensure at 3.00, continuing education at 4.00, practice at 5.00, installation at 6.00, business licensure at 7.00, training at 8.00, and permits at 9.00.

The class map places this program precisely. Above the journeyperson tier stand the Master classes, M-1 and M-2: a Master is authorised to operate a regular place of sheet metal business and to perform sheet metal work and supervise apprentices. Below it stands the Apprentice, Class A, authorised to perform sheet metal work under the direct supervision of a Master or Journeyperson in the employ of a Master. The journeyperson definition sits between them: a holder of a valid Class J-1 or J-2 license, authorised to perform sheet metal work and supervise, but not employ, apprentices. Every word is load-bearing β€” perform, supervise, not employ β€” and the practice rules add two constraints: two or more journeypersons shall not associate as partners, and journeypersons shall engage in sheet metal work only in the name printed on their licenses. Since the grandfathering period ended on February 18, 2011, licenses may only be obtained by examination.

The trade itself: what sheet metal work includes β€” and excludes

Sheet metal work is the manufacturing, fabrication, assembling, handling, erection, installation, dismantling, alteration and repairing of all commercial duct or air exhaust systems, except for refrigeration and combustion units; the installation of commercial fans, sheaves, belt guards, dampers, louvers, screens, registers, grilles, diffusers, sound traps, attenuators, mixing boxes and access doors in connection with duct or air exhaust systems; commercial and industrial architectural sheet metal watershed roof systems, except for roof coverings and associated metal flashing; the testing, adjusting and air-balancing of all air-handling equipment and ductwork; and the installation of commercial and industrial kitchen hoods, kitchen vents, bathroom exhaust vents and fans. The definition is generous inside its field and fenced at its edges: sheet metal work shall not include the work conducted by a licensed pipe fitter, oil burning technician, refrigeration technician, plumber or gasfitter. Field practice runs through the Board’s own instruments: the practice rules at 271 CMR 5.02, the installation rules at 271 CMR 6.00, and the permits regime at 271 CMR 9.00, under which a permit must be issued before any erection, installation or dismantling of sheet metal work, and permits are issued only to licensed Journeyperson and Master Sheet Metal Workers.

Within the trade, the two classes divide by reach. A Class J-1 holder may independently perform any task, function or service included within the practice of sheet metal work. A Class J-2 holder may independently perform sheet metal work on residential jobs and non-residential jobs which are under three stories and up to and including 10,000 square feet β€” printed here, as throughout, in the regulation’s own terms.

The examination arrangement: Board approval, vendor administration

The route to a sitting has two stages. The Board receives, reviews and approves or denies all applications. The applicant applies online through eLIPSE, attested under the pains and penalties of perjury, with the Commonwealth’s fee submitted with the application; incomplete applications are retained for 180 days. Once an application is approved, the Board notifies the vendor, and PSI Exams notifies the approved applicant, who schedules the examination and pays the examination fee directly through the vendor. A candidate who has not been approved has no sitting to schedule.

At the centre, the bulletin’s administration rules apply to all three examinations alike. Candidates arrive at least 30 minutes early. Identification requires two forms: one valid government-issued identification with photograph and signature, and a second with signature and the preprinted legal name. Calculators are limited to non-programmable, non-printing, silent, battery-operated models without alphabet keys. The pass standard’s source discipline belongs here too: the regulation requires a passing score and prints no percentage, while the bulletin states the operative figure in full β€” “A passing score is a MINIMUM of 70% correct” β€” and each outline heading repeats it as the percentage required to pass. Every candidate leaves with a printed score report; a failing candidate’s report shows the overall score and per-section correct counts, making it a study document for a retake, while a passing candidate’s report does not carry the section detail. A failing candidate is additionally given 30 minutes at the end of the examination to review the items missed, at no charge.

A word on the examination’s form, because the statute invites a misreading. Section 240 says the Board shall examine applicants as to their practical knowledge of sheet metal work. That phrase describes the examination’s subject, and the examination the bulletin administers is a computer-administered, open-book, multiple-choice examination. No hands-on station or practical demonstration is stated anywhere in the sources.

Examination one: J-1 Unrestricted β€” the layout-led paper

The general J-1 examination is 80 questions in 150 minutes, open book, at the common passing standard. Its outline, stated in full because the weights are the study plan: General Knowledge, 8; Safety, 8; Duct Sizing, Design, Hangers and Supports, 8; Duct Fabrication and Installation, 5; Layout, 12; Ventilation System Accessories and Devices, 7; Commercial Kitchen Exhaust Systems, 6; Life Safety Ventilation Systems and Accessories, 6; Blue Print Reading, 4; Air Balancing, 4; Metal Roofing Systems and Accessories, 4; Plenums and Casing, 3; Welding, 5 β€” eighty items in all. Three readings follow. First, Layout is the paper’s centre of gravity: at 12 questions it outweighs every other area by half again, and pattern development fluency is the highest-yield skill in this sitting. Second, the ventilation-and-life-safety cluster β€” accessories and devices, kitchen exhaust, life safety systems β€” totals 19 questions, a quarter of the paper, and it is code-dense: this is where the listed NFPA editions earn their shelf space. Third, the paper is broad at its tail: blueprint reading, air balancing, metal roofing systems and plenums contribute 15 questions across four crafts, so no candidate passes on ductwork alone. Welding’s 5 questions are examined through a reference that may not enter the room.

Examination two: J-1 Metal Roofing β€” the parallel paper

The Metal Roofing examination matches the general J-1 in size, time and standard β€” 80 questions, 150 minutes, open book β€” and differs in almost everything else. Its outline is: General Safety, 4; General Trade Knowledge, 12; Custom Metal Roofing β€” Layout, Fabrication and Installation, 25; Pre-fabricated Engineered Metal Roofing Systems, 25; Soldering, 2; Massachusetts 8th Edition Building Code, 4; Massachusetts Sheet Metal Regulations 271 CMR, 4; Blue Print Reading, 4 β€” eighty items, half of them roofing systems proper, split evenly between custom work and pre-fabricated engineered systems. Its allowed references are the roofing shelf: the Massachusetts 8th Edition Building Code; the SMACNA Architectural Sheet Metal Manual, 7th Edition (2012); the Metal Roofing Systems Design Manual, First Edition; and 271 CMR. Neither the mechanical code nor the NFPA set appears on it.

One strict boundary governs this examination’s treatment. The bulletin lists it among the categories of licensure offered, as a separate examination within the J-1 class, with its own outline and books. The sources do not state how it relates to J-1 licensure in practice β€” as an endorsement, an alternative route, or a standalone category β€” and this guide states no relationship. What a candidate’s particular roofing practice requires should be confirmed with the Board.

Examination three: J-2 Restricted β€” the bounded paper

The J-2 examination is 60 questions in 120 minutes, open book, at the same passing standard, on the general J-1’s reference shelf. Its outline is: General Knowledge, 8; Safety, 7; Duct Sizing, Design, Hangers and Supports, 8; Duct Fabrication and Installation, 6; Layout, 8; Ventilation System Accessories and Devices, 7; Commercial Kitchen Exhaust Systems, 4; Life Safety Ventilation Systems and Accessories, 3; Blue Print Reading, 4; Air Balancing, 3; Plenums and Casing, 2 β€” sixty items. Set beside the J-1 outline, the restricted paper’s character is exact: the Metal Roofing and Welding areas are absent altogether; Layout keeps its full weight of 8 within a smaller paper, making it proportionally heavier here than anywhere else in the family; and the remaining areas compress roughly in proportion to the license’s bounded reach. Candidates should resist treating J-2 as the J-1 paper with questions removed β€” its weights are its own β€” or its 60-and-120 figures as the family’s general figures.

Pretest questions and the review of missed items

First, pretest: in addition to the number of questions per examination, a small number of five to ten pretest questions may be administered during the examinations; these questions will not be scored, and the time taken to answer them will not count against examination time. A candidate therefore cannot infer the paper’s length from the questions encountered. Second, review: a candidate who fails is given 30 minutes at the end of the examination to review the items missed, at no charge β€” used well, the first study session of the retake, read against the section counts on the failing score report.

The reference shelves: allowed, not allowed, and the edition rule

The bulletin’s general reference rule governs every shelf in this family: all the reference materials listed were used to prepare the questions; except for codebooks, later editions may be used as they become available; and for code questions, the examination will be based only on the edition of the codebook that is listed. For the J-1 and J-2 examinations, the allowed shelf is: the 2009 International Mechanical Code; NFPA 96, 2008; NFPA 90A, 2009; NFPA 90B, 2009; NFPA 92A, 2009; NFPA 92B, 2009; the SMACNA HVAC Duct Construction Standards, Metal and Flexible, 2005, 3rd edition; the SMACNA Architectural Sheet Metal Manual, 7th Edition, 2012; and 271 CMR. Not allowed in the examination centre, though used to prepare questions, are: 29 CFR Part 1926, the OSHA construction standards; Modern Welding, 11th Edition, 2014; and the NCCER Sheet Metal texts, Levels 1 through 4, 3rd Edition, 2008. The practical meaning of the not-allowed list is that three bodies of content β€” construction safety regulation, welding, and the NCCER curriculum’s ground β€” must be carried into the room in the candidate’s head, as closed-book material inside an open-book sitting.

The handling rules are part of the examination’s discipline. Candidates bring their own references; nothing on the shelf is supplied. References may be highlighted, underlined, annotated and indexed before the session, but may not be written in during it. No additional papers are permitted. Tabs must be permanent; temporary tabs, such as sticky notes, are not allowed. A shelf prepared beforehand is a legitimate part of preparation; a shelf annotated in the room violates the sitting’s rules. The Metal Roofing shelf is the four-item roofing list from its own section, and it does not merge with this one.

Tested against field: a gap of multiple code cycles

No fact in this program needs more emphasis than the distance between the bulletin’s editions and the Commonwealth’s current code. The tested layer is fixed by the bulletin updated May 1, 2024: code questions are keyed to the International Mechanical Code of 2009, with the NFPA set at its 2008 and 2009 editions, the SMACNA duct standards at 2005, and β€” for the Roofing examination β€” the Massachusetts 8th Edition Building Code. The field layer is the State Building Code in its Tenth Edition, first effective October 11, 2024 and based on modified versions of the 2021 International Codes, including the International Mechanical Code of 2021. The gap is three code cycles.

Massachusetts then refines the field layer in a way that matters specifically to this trade. The building code’s mechanical adoption expressly shall not be deemed to apply to work governed by the specialised codes under M.G.L. c. 143, Β§ 96, including sheet metal work as defined in M.G.L. c. 112, Β§ 237. Sheet metal work in the field is therefore governed in the first instance by the Board’s own regime β€” the practice, installation and permits rules of 271 CMR β€” inside the Tenth Edition environment. The working rule is symmetrical: answer the examination from the bulletin’s editions, because code questions are based only on the listed editions; and build, install and permit work under the current code and the Board’s rules. A source that tells candidates this examination tests the 2021 mechanical code has merged layers this program exists to keep apart.

Eligibility in full: the J-1 gate, the J-2 gate, and the shared elements

For Class J-1, 271 CMR 3.01(2) sets six elements, all required: application in the Board’s prescribed manner, attested under the pains and penalties of perjury; good moral character and a high school diploma or equivalency; documented experience as a licensed apprentice totalling 8,000 hours of sheet metal work over no less than five years, within the ten years preceding application, under the direct supervision of a holder of a Class J-1 or Class M-1 license; documented completion of a Board-approved 750-hour Journeyperson’s Course within ten years of application; a passing score on the Board’s examination; and the non-refundable fee set under M.G.L. c. 7, Β§ 3B.

For Class J-2, the Board’s application pages and consumer fact sheet state the restricted scale in the same structure: documentary proof, within the ten years preceding application, of 4,800 hours of licensed apprentice training and 450 hours of Board-approved training classes over no less than three years. The shared elements β€” application, character, schooling, a passing score and the Β§ 3B fee β€” apply across the classes. The application file runs through eLIPSE and comprises the current Apprentice license, a two-by-two colour passport photograph, the high school diploma, transcripts or equivalency record, training certificates, the Statement of Experience Form, the CORI Authorisation Form and the class Education Verification. Over both gates stands the credit fence: no credit will be given for any work experience in Massachusetts after February 19, 2011 without being a licensed apprentice employed by a master sheet metal worker. A candidate short of hours has exactly one remedy: more licensed apprentice time.

Finally, the absence that defines the contrast with the companion Massachusetts program: no EPA certification, refrigeration credential or other-trade license is named as a prerequisite for either class. Sheet metal licensure gates on apprenticeship, coursework and examination alone.

Fees, retakes and appeals: two payees and three clocks

The fee structure separates cleanly once the payees are named. The Commonwealth instrument is the license processing and issuance fee of $155 β€” the bulletin’s fee table calls it the application processing and initial license fee, at $155 for all three examinations alike, non-refundable, payable to the Commonwealth of Massachusetts and submitted online with the application. The vendor instrument is the PSI examination administration fee of $180 for each examination, submitted to the vendor upon approval, payable by card, cashier’s check or money order. The re-examination fee is $180 to PSI, non-refundable, and failing to appear forfeits all fees paid in connection with that examination. This guide nowhere adds the two instruments into a combined figure, because no such combined fee exists: the sums are paid to different payees, at different stages, for different functions.

Three clocks govern failure and rescheduling. The rescheduling clock: a candidate may cancel or reschedule without forfeiting the fee if notice is received two days before the scheduled date, and a voice mail message is not an acceptable form of cancellation. The retake clock: a candidate who fails has six months from the application approval date to successfully retake the examination; beyond that window, a new Board application is required. The improvement clock: a candidate who has not passed after three attempts shall provide satisfactory proof to the Board of having successfully completed self-designed learning objectives or an examination preparation course. Beside them, an appeal clock: a failing candidate may appeal in writing to the Board within 30 days of the date on the vendor’s rejection notice.

Term, renewal and the continuing-education negative

The license term is two years, individually anchored. Under 271 CMR 3.02(1), each license originally issued is valid for a minimum of twelve months and expires on the 28th day of the licensee’s birth month, and each renewal falls on the anniversary of that date. Renewal requires the completed application and fees before expiration, and runs online through eLIPSE; the renewal fee is $80, distinct from both application-stage fees. An expired license is not in good standing. Reinstatement within two years requires the renewal fee for the current period plus one late fee; a license expired for two years or more may require retesting; and working on an expired license is a violation.

Continuing education is the program’s verified negative. The full current text of 271 CMR 4.00 provides that licensed sheet metal workers are encouraged to continue to expand knowledge by attending educational programmes; however, no continuing education is currently required by the Board. The chapter anticipates that the Board will add such a requirement at some future date, through a separately promulgated regulation change. The statute matches: Β§ 244 says the Board may adopt continuing education rules as a renewal condition β€” the authority is permissive and unexercised in the current chapter. Two consequences follow. Renewal planning is a matter of date and fee, not of accumulated hours. And any source quoting a specific continuing-education hour figure, or an annual renewal cycle, for Massachusetts sheet metal licensees is contradicted by the primary text on both points.

A study plan built on the matrix

Preparation succeeds by keeping the matrix intact throughout. First, fix the class. Every subsequent decision β€” outline, shelf, pacing β€” follows from the target examination. Second, weight by the outline. For the general J-1, Layout leads and the ventilation cluster follows; for the J-2, Layout’s proportional weight is higher still; for Roofing, the two 25-question areas dominate. Study hours should follow the outline’s proportions, not the candidate’s comfort proportions. Third, build the shelf early. The allowed references should be acquired in the listed editions, tabbed, indexed and highlighted during study, so the book carried into the room is the book used for months; the not-allowed references should be studied as memorised content. Fourth, practise retrieval, not recognition. Open-book examinations are lost on search time: timed drills should measure how fast a provision can be found in the tabbed shelf, with the layers labelled β€” tested or field β€” until the distinction is automatic.

The errors this program is built to catch

Blending the classes β€” quoting 60 questions as the journeyperson figure, or the J-1’s 8,000 hours as the restricted gate β€” fails the family’s first discipline. Attributing the 70% to 271 CMR misstates its source: the regulation requires a passing score; the percentage is the bulletin’s. Updating the tested editions β€” preparing code answers from the 2021 mechanical code because it is current in the field β€” contradicts the rule that code questions are based only on the listed edition. Merging the fees erases the two-payee structure. Claiming a continuing-education requirement, or an annual term, imports inventions the primary text refutes. Importing an EPA prerequisite blends two sovereign Massachusetts frameworks. Describing Β§ 240’s practical knowledge as a hands-on practical prepares for a bench test the bulletin does not administer. And stating how the Metal Roofing examination converts into licensure claims a relationship no source states.

The companion program page for this guide is at /massachusetts-journeyperson-sheet-metal-exam-prep/.

Frequently asked questions

What fees are payable, and to whom?

$155 to the Commonwealth with the application, for license processing and issuance, non-refundable. $180 to PSI upon approval, for examination administration; a re-examination is another $180 to PSI. Renewal is $80. No combined single fee exists.

What happens after failing?

The candidate reviews missed items for 30 minutes at the end of the sitting at no charge, receives a score report showing overall and per-section results, and has six months from the application approval date to retake successfully before a new Board application is needed. After three unsuccessful attempts, the candidate must show completion of self-designed learning objectives or an examination preparation course.

How long does the license last, and is continuing education required?

Two years, expiring on the 28th day of the licensee’s birth month, renewed online through eLIPSE at $80. No continuing education is currently required by the Board under 271 CMR 4.00.

Is PassProfessor affiliated with the Board or PSI?

No. PassProfessor is an independent preparation provider. The Board alone determines eligibility and licenses; PSI schedules and conducts the examinations.

When does enrollment open for the PassProfessor program?

The program is in the works and enrollment is not yet open. Leave an email address and PassProfessor will write to you when it is ready β€” and only about this program.