Iowa’s Master HVAC/Refrigeration license is issued by the Plumbing and Mechanical Systems Board within the Department of Inspections, Appeals, and Licensing, under Iowa Code chapter 105. The examination, through Kirkwood Community College, is an open-book sitting of 100 questions in four hours, keyed to the 2024 International Mechanical Code and the 2024 edition of NFPA 54. This guide works through the credential, the outline, and the route in full.
This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.
The credential at a glance
| Item | Verified position |
|---|---|
| Program | Iowa Master HVAC/Refrigeration: the master examination in the HVAC-refrigeration discipline, titled by the provider as Master HVAC/Refrigeration with Gas |
| Regulator | Plumbing and Mechanical Systems Board (PMSB), within the Department of Inspections, Appeals, and Licensing (DIAL) |
| Law and rules | Iowa Code chapter 105; 481 IAC chapters 425–435 (licensing chapters repromulgated effective June 19, 2024, and renumbered to 481 on April 2, 2025) |
| Examination provider | Kirkwood Community College, the Board’s approved examination provider |
| Examination format | Written, proctored, in person or online; 100 questions; four hours; open book with approved references only |
| Passing standard | A score of 75 percent or better is considered passing |
| Tested references | International Mechanical Code, 2024 edition; NFPA 54 National Fuel Gas Code, 2024 edition; Modern Refrigeration and Air Conditioning, 21st edition |
| Field code | State Mechanical Code: International Mechanical Code, 2024 edition, effective March 26, 2025 |
| Credential term | Three-year cycle, expiring June 30 in the renewal year; eight hours of continuing education per period for a single license |
| Administrator note | PassProfessor is independent and is not affiliated with the Plumbing and Mechanical Systems Board, DIAL, or Kirkwood Community College |
This guide is the companion to the Iowa Master HVAC/Refrigeration program page at /iowa-master-hvac-refrigeration-exam-prep/. The program page states the position briefly; this guide states it in full.
Reading the Iowa facts: three layers that must not be merged
Iowa preparation goes wrong most often at the level of layers. The statute layer, Iowa Code chapter 105, creates the license system: the disciplines, the master and journeyperson tiers, the contractor license and the master of record, and the scope definitions in section 105.2. The rule layer, 481 IAC chapters 425–435, carries the operating detail: chapter 426 is the State Mechanical Code, chapter 428 carries licensure fees, chapter 429 carries application, licensure, and examination, chapter 430 carries alternative pathways, chapter 431 carries licensee practice, chapter 432 carries continuing education, and chapter 434 carries discipline. The provider layer, Kirkwood Community College’s published examination material, carries the sitting itself: the outline percentages, the allowed references as listed for the examination, and the examination-day rules. A fact that lives in one layer should not be quoted as if it lived in another. The pass standard, for example, is a rule sentence, quoted in this guide exactly as the rule prints it. The outline is a provider document. The code edition is both a rule fact, through the State Mechanical Code adoption, and a provider fact, through the reference list — and in Iowa, unusually, the two agree.
Two currency warnings belong at the front of any Iowa study plan. First, the licensing chapters were repromulgated effective June 19, 2024 and editorially renumbered from 641 to 481 on April 2, 2025. Material citing the chapters under their former number, or naming the former department that once housed this board, is stale and should be set aside wherever it conflicts with the current 481 citations. Second, older Iowa code material points at the prior mechanical code edition. The State Mechanical Code moved directly from that prior edition to the 2024 edition effective March 26, 2025. There was no intervening adoption of the edition between them, and no part of current Iowa preparation — examination or field — should be built on the assumption that there was.
The code position in depth: one edition, two books
For this license, the tested edition and the adopted edition are the same edition. The State Mechanical Code adopts Sections 101–102 and Chapters 2–15 of the International Mechanical Code, 2024 edition, by reference. The examination’s listed mechanical reference is that same 2024 edition. The Board is required to adopt the current version of the mechanical code within six months of its release, which is the mechanism that produced the direct jump: when Iowa moved, it moved to the current edition, past the edition it had never adopted. Candidates should understand what that means for their bookshelf. Material written to the prior edition is not a close approximation of the current Iowa position; it is a description of a code Iowa no longer uses in the field and no longer keys in the room. Material written to the middle edition describes a code Iowa never used at all. Only 2024-edition material describes the Iowa sitting.
Fuel gas is the deliberate exception to the single-family picture, and it is an exception of book family, not of currency. Iowa does not adopt the International Fuel Gas Code. Iowa amendments replace references to that code with NFPA 54, NFPA 58, chapter 226 of the Iowa administrative material, and the state plumbing code. In the field, fuel gas work runs through NFPA 54 and NFPA 58. In the room, the listed fuel gas reference is NFPA 54, 2024 edition. The discipline’s own definitions explain why gas occupies this position: HVAC, as Iowa defines it, includes all natural, propane, liquid propane, or other gas lines associated with any component of an HVAC system, and refrigeration carries the same inclusion for its associated gas lines. Gas piping is therefore inside the master’s scope and inside the examination, but it is examined from the NFPA book. A study plan that treats the gas piping area as a chapter of the mechanical code misfiles 8 percent of the sitting and, more importantly, mistrains the habit the field requires, which is reaching for NFPA 54 when the question is a gas question.
The local layer needs one sentence of care. The state codes apply to state-owned buildings and in each local jurisdiction, but a local jurisdiction is not required to adopt them by ordinance, and a jurisdiction that does adopt may be more restrictive. Chapter 105 preempts local licensing, so the license travels, while permit and inspection fees remain local. None of that changes the examination: the sitting keys to the state position, and local variation is field knowledge, not examination material.
Who the master is: scope, responsibility, and the contractor connection
Iowa’s master is defined by function: a person who works in the planning or superintending of the design, installation, or repair of the systems in the discipline and is otherwise lawfully qualified to conduct the business of those systems. The HVAC-refrigeration license allows the individual to perform the work defined as HVAC and refrigeration, and a qualified master may also work at all journeyperson roles in the discipline. Read together, the master tier is both a working tier and a responsibility tier, and the examination is built for a candidate who will plan and answer for work, not only perform it.
The contractor connection gives that responsibility its business form. A contractor license requires an application and Board fees, proof relating to workers’ compensation and unemployment insurance, a permanent place of business, registration under Iowa Code chapter 91C in the same application, and holding or employing at least one master licensee. The master of record holds an active master license, is responsible for proper designing, installing, and repairing, and is actively in charge. A contractor may not do business in a discipline without a master of record for each discipline at all times, and a master may serve only one contractor per discipline absent prior Board approval. When the master of record is lost, the contractor may continue for up to six months if it notifies the Board within 30 days; the departing master must likewise notify within 30 days. A sole proprietor who performs the work must personally be a licensed master in the discipline.
Scope boundaries complete the picture. The broader Mechanical license combines HVAC, refrigeration, sheet metal, and hydronic work and is a separate license; there is no master sheet metal license. The electrical boundary is narrow: a master or journeyperson in these disciplines is exempt from a special electrician’s license only to disconnect and reconnect existing air conditioning and refrigeration systems. Fuel gas piping also appears in the plumbing definition, so a described job can sit at an overlap the candidate must sort by definition rather than by habit.
The route, step by step
Step one — establish the gate. The applicant for the master examination must establish one of two bases: previous licensure as a master in the applicable discipline, or previous licensure as a journeyperson in the applicable discipline with at least two years of journeyperson experience in that discipline. The statute mirrors the same structure, and the rule quantifies the journeyperson route at at least two years. The general floor for any license in this system is at least 18 years of age. Candidates whose background is out-of-state master licensure should note that this route still leads to the Iowa examination; it is an eligibility basis, not a waiver.
Step two — obtain Board approval. Submit the State of Iowa Examination Candidate Application, online or on paper, with the candidate fee of $35 per trade examination, at least 15 business days before the intended examination. Staff verify eligibility and issue an Exam Approval Letter with the provider’s scheduling instructions. Approval is valid for one year. Within that year the candidate may test as many times as necessary, paying the provider’s fee for each attempt; no maximum number of attempts inside the approval year is published, and this guide states none. After the year, a candidate application and fee are required again. Published figures for the provider’s per-attempt fee do not agree across the provider’s own published figure and the differing figures on the Department’s own pages, so this guide prints no single examination dollar; the amount charged at registration should be confirmed with the provider at scheduling.
Step three — sit the examination. The sitting is written and proctored, in person or online, offered periodically during the year at rotating Iowa sites: 100 questions, four hours, open book with approved references only. The score is shown on screen at the end, as the percent of correct answers.
Step four — meet the standard. The rule states it in one sentence, and this guide prints it in that sentence: “A score of 75 percent or better is considered passing.”
Step five — apply for the license. Passing does not itself issue a license. Licensure after the examination is a separate required step, the initial fee is prorated for a partial period, and the clock matters: a passing score expires if the applicant does not apply for licensure within two years of notification of passing, after which the examination must be retaken and passed. The master license fee for the three-year period is $240, a Board license-layer figure, kept separate in this guide from the $35 candidate fee and from any provider examination charge, because the three amounts buy three different things from two different instruments.
Step six — hold the license on its cycle. The license runs to June 30 of the third year, with renewal and continuing education as described in the renewal section of this guide. A candidate who fails at any sitting may retake at a future scheduled time inside the approval year, registering and paying for the attempt through the provider.
The outline in full
Kirkwood’s outline states the approximate percentage of the 100 questions in each area, and states that each outline lists all topics covered. For the Master HVAC/Refrigeration examination the distribution is as follows, and a serious study plan should be built in its proportions.
Refrigeration Term System, Operation — 20 percent
The largest single area, at one question in five, covers refrigeration terminology, systems, and operation. Its listed companion reference, Modern Refrigeration and Air Conditioning in its 21st edition, carries much of this area’s textbook content, and candidates should expect the area to test the operating reasoning of the trade — cycles, components, and system behaviour — at master level, where the question is often what the system is doing and what the responsible licensee does next, rather than what a part is called.
Venting, Duct, Combustion Air — 18 percent
Venting, duct work, and combustion air together form the second-largest area. This is mechanical-code territory in the main: how air, exhaust, and combustion products move, and the provisions that govern the pathways they move through. At 18 percent it outweighs installation and electrical content alike, and candidates who allocate study time by habit rather than by the published distribution reliably underweight it.
HVAC Terms, Principles, Administration — 16 percent
Terminology, principles, and administration open the distribution. The administration element is the Iowa layer inside the trade sitting: licensing structure, scope definitions, responsibilities, and Board rule. Candidates who are strong tradespeople and weak on the Iowa framework lose ground here first, and the loss is avoidable, because the material is short, published, and stable inside a licensing cycle.
HVAC Installation — 14 percent
Installation content tests the discipline’s core work as the code and trade references govern it: placing, connecting, and completing systems so that they satisfy the provisions the other areas state in the abstract. Installation questions reward candidates who can move between the mechanical code’s requirements and the described job without losing either.
HVAC Electrical — 13 percent
Electrical content sits inside the discipline’s scope: motors, controls, and the electrical work the HVAC-refrigeration licensee actually performs, bounded by the narrow disconnect-and-reconnect position described in the scope section. Candidates should resist studying general electrical material beyond that boundary; the sitting examines the discipline’s electrical content, not another trade’s.
Boilers, Exhaust, and Fire Protection — 11 percent
Boilers, exhaust, and fire protection form a combined area of just over one question in ten. Its combination is itself a study instruction: the sitting treats these subjects as one neighbourhood of provisions, and candidates should prepare them together rather than as three unrelated fragments drawn from different corners of their books.
Gas Piping — 8 percent
The smallest area by percentage and the most distinctive by source. Gas piping is examined from NFPA 54, 2024 edition — the only area of the sitting keyed to that book — and it tests the discipline’s statutory gas-line scope. Eight percent of a master sitting is eight questions at this examination’s size, and they are the questions most directly lost by candidates who studied gas from the wrong book family. No separate scored and unscored division of the 100 questions is published for this examination, and candidates should plan pacing on the published figures alone: 100 questions, four hours, the standard stated above.
Examination day in full
The open-book rules reward work done before the sitting and penalise improvisation during it. References must be the approved references; code references may be bound or loose-leaf; photocopies may not be used. Books may not contain handwritten or additional notes, and anything written in a book during the examination is confiscated. Highlighting done before arrival is acceptable, and permanent tabbing is acceptable; removable sticky notes are not. Books are checked before and after the examination and may not be shared. Scratch paper is provided and confiscated at completion. The allowed equipment is specific: a battery-operated, nonprogrammable calculator without storage or printing capability, an architect’s scale or rule, magnifying glasses or eyeglasses, and a foreign language and English translation dictionary if needed. Phones and electronic devices are not allowed in the testing area. Candidates should arrive at least 30 minutes early, with government-issued photo identification bearing a signature, in a name exactly matching the registration name. Disability accommodations are provided at no additional charge on documentation submitted at least two weeks before the examination date.
One rule deserves emphasis, because it interacts directly with the 2024 jump. Questions are based on the listed editions, but a reference book physically brought to the examination may be from any edition. The permission is about what may be carried in, not about what the questions key to. In this cycle Iowa skipped an edition, so a candidate carrying the prior edition is carrying a book two editions behind the key. The rational preparation is unambiguous: study, tab, and carry the 2024 editions. Results are handled narrowly: the score appears on screen at the end, results are confidential to the applicant and the Board, the examination is not subject to review by applicants, and the provider will identify failed sections on request, without access to questions or answers. There is no practical or drawing component; the examination is written and proctored throughout.
A study plan built on the published distribution
First, rebuild the bookshelf. Shelve every item keyed to the prior mechanical code edition, to the middle edition Iowa never adopted, or to a fuel gas code Iowa does not adopt. What remains should organise under three spines: the 2024 mechanical code, NFPA 54 in its 2024 edition, and the 21st edition refrigeration text. Second, allocate time by the outline. Refrigeration operation and venting, duct, and combustion air together carry 38 percent of the sitting; gas piping carries 8 percent of the questions and a larger share of the risk, because it is the only area requiring a book change. Third, learn the Iowa layer as a short, closed syllabus — chapter 105’s definitions and tiers, the candidate-approval route, master-of-record duties, and the renewal rules. Fourth, practise the open-book skill itself: timed practice with the actual references, under the actual prohibitions, is the only rehearsal that transfers. Fifth, finish with mixed sittings, scored area by area, while there is still time to move the remaining losses.
The errors this examination is built to catch
Studying the wrong mechanical edition is the defining Iowa error of this cycle, in either of its two forms: the prior edition, which Iowa has left behind, or the middle edition, which Iowa never adopted. Studying gas from the wrong family is its companion: fuel gas in Iowa keys to NFPA 54, in the field and in the room. Treating Master and Contractor as one license confuses both the eligibility analysis and the responsibility analysis the administration content examines. Assuming a published division of the 100 questions into scored and unscored groups invents a fact no Iowa source publishes. Assuming reciprocity for an HVAC-refrigeration license from another state mistakes a plumbing-only published agreement for a general policy. Carrying an older book because carriage is permitted confuses the desk rule with the keying rule. And stopping at the pass — treating the examination as the end of the route — risks the two-year application fuse on the passing score itself. Each of these errors is a layer error before it is a knowledge error, which is why this guide began with the layers.
After the sitting: renewal, education, and standing
Licenses in this system expire June 30 every three years regardless of issue date; the current period runs July 1, 2026 through June 30, 2029. Renewal opens May 1 of the third year and renewal applications are due at least 30 days before expiration. The grace structure is forgiving in sequence and unforgiving at its end: one month after expiration runs without a late fee and practice continues without fines or penalties; August renewal carries a $60 late fee; renewal after August through the following June carries a $100 late fee; the license remains valid for practice for up to two months past expiration and then lapses; and after a lapse of more than one year, reinstatement requires either retaking and passing the examination or completing all continuing education for each missed period, at the full license fee with no proration.
Continuing education for a single license is eight hours per period — two of safety, two of code, and four in the discipline — with an hour defined as at least 50 minutes, Board-approved courses and instructors, no double-counting of a repeated course, and up to one-half of the hours permitted online. The duty applies to active and inactive licensees alike. Inactive status must still be renewed, is not valid for practice until reactivated, and cannot support service as a master of record. On alternative pathways, hold the sourced positions and no others: licensure by verification still requires proof of passing the applicable Iowa examination, and the work-experience pathway requires three or more years of full-time work in the four years before application, with full time defined as at least 1,700 hours in a one-year period, plus passing any necessary examinations. Federal refrigerant certification is not a condition of this license in any source relied on for this guide.
Frequently asked questions
Which documents govern this license?
Iowa Code chapter 105 creates the system, and 481 IAC chapters 425–435 carry its operation — chapter 426 for the State Mechanical Code, chapter 429 for application and examination, chapter 432 for continuing education, among them.
Why do older Iowa citations look different?
The licensing chapters were repromulgated effective June 19, 2024 and renumbered to 481 on April 2, 2025. Citations under the former chapter number, and references to the department that formerly housed the board, are stale.
What exactly did Iowa adopt on March 26, 2025?
The State Mechanical Code adopted the International Mechanical Code, 2024 edition, effective that date — a direct move from the prior 2018 edition, with no intervening adoption of the edition between them.
Is the field code the same as the examination code?
Yes, for this license. The adopted field edition and the examination’s listed mechanical edition are both the 2024 edition. Fuel gas is the exception of family, not edition: both field and examination key fuel gas to NFPA 54 rather than to a fuel gas code Iowa does not adopt.
What are the seven outline areas?
Refrigeration Term System, Operation at 20 percent; Venting, Duct, Combustion Air at 18 percent; HVAC Terms, Principles, Administration at 16 percent; HVAC Installation at 14 percent; HVAC Electrical at 13 percent; Boilers, Exhaust, and Fire Protection at 11 percent; and Gas Piping at 8 percent.
What happens after passing?
Licensure is a separate step. The applicant applies for the license, with the initial fee prorated for a partial period, within two years of notification of passing; after two years the passing score expires and the examination must be retaken and passed.
How long is the license good for, and what does renewal require?
The cycle is three years, expiring June 30 of the third year. Renewal requires the renewal application and fee and, for a single license, eight hours of continuing education in the period in the 2–2–4 split of safety, code, and discipline hours.
What does a master of record do?
The master of record holds an active master license, is responsible for proper designing, installing, and repairing, and is actively in charge of the contractor’s work in that discipline. A contractor must have one for each discipline at all times, and a master may serve only one contractor per discipline without prior Board approval.
When does enrollment open for the PassProfessor program?
The program is in the works and enrollment is not yet open. Leave an email address on this page and PassProfessor will write to you when the program is ready — and only about this program.
