Iowa Journeyperson Mechanical Exam Guide: The Combined License, Its Two Routes, and the Systems Outline

Iowa’s Journeyperson Mechanical license is issued by the Plumbing and Mechanical Systems Board within the Department of Inspections, Appeals, and Licensing, under Iowa Code chapter 105. It is the broad journeyperson license — HVAC, refrigeration, sheet metal, and hydronic work in a single credential — reached either by its own open-book Kirkwood examination of 75 questions in two hours or by a statutory combination route. The PassProfessor Iowa Journeyperson Mechanical program prepares candidates for that examination and the licensing structure around both routes.

This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.

The credential at a glance

ItemVerified position
ProgramIowa Journeyperson Mechanical: the journeyperson examination in the mechanical discipline, titled by the examination provider as Journeyperson Mechanical with Gas
RegulatorPlumbing and Mechanical Systems Board (PMSB), within the Department of Inspections, Appeals, and Licensing (DIAL), under Iowa Code chapter 105 and 481 IAC chapters 425–435
Examination providerKirkwood Community College, the Board’s approved examination provider
Examination formatWritten and proctored, in person or online; 75 questions; two hours; open book with approved references only
Passing standardA score of 75 percent or better is considered passing — the Board’s general examination rule, at 481 IAC 429.6(2)(d)
Tested referencesInternational Mechanical Code, 2024 edition; NFPA 54 National Fuel Gas Code, 2024 edition — two references only
Field codeState Mechanical Code: International Mechanical Code, 2024 edition, effective March 26, 2025
Fees, as separate instrumentsBoard examination-candidate fee $35 per trade examination; Kirkwood examination fee $119 per attempt; Board journeyperson license fee $180 for the three-year period
Credential termThree-year cycle, expiring June 30 in the renewal year
Administrator notePassProfessor is independent and is not affiliated with the Plumbing and Mechanical Systems Board, DIAL, or Kirkwood Community College

This guide follows the license’s own logic: breadth first, then routes, then the paper. Iowa Code chapter 105 creates the system, and the Board’s rules at 481 IAC chapters 425–435 operate it — chapter 426 for the State Mechanical Code, chapter 428 for fees, chapter 429 for application, licensure, and examination, chapter 430 for alternative pathways, chapter 431 for practice, chapter 432 for continuing education, and chapter 434 for discipline. The licensing chapters were repromulgated effective June 19, 2024 and editorially renumbered from the Public Health title to the Inspections and Appeals title on April 2, 2025, so citations carrying the older title number belong to a superseded layer. The Board sits within DIAL and includes journeyperson and master mechanical professionals among its twelve voting members.

One license, four disciplines

The Board issues master licenses for plumbing, mechanical, HVAC-refrigeration, and hydronic professionals, and journeyperson licenses for plumbing, mechanical, HVAC-refrigeration, sheet metal, and hydronic professionals. The Mechanical license is the combining entry in that list. Its scope sentence in the statute is short: a mechanical license allows an individual to perform work defined as HVAC, refrigeration, sheet metal, and hydronic. Each of those four terms is separately defined, and the definitions — not the label — decide what a holder may do on a given job.

HVAC means heating, ventilation, air conditioning, ducted systems, or any type of refrigeration used for food processing or preservation, including all associated gas lines. Refrigeration means a system of refrigeration, regardless of power level, if intended for food processing and product preservation, including associated gas lines. Sheet metal means heating, ventilation, air conditioning, pollution control, fume hood systems and related ducted systems, and equipment installation associated with such a system, and it expressly excludes refrigeration and electrical lines and all gas lines associated with a sheet metal system — so the sheet metal component contributes ducted and ventilation work, not gas work. Hydronic means a heating or cooling system transferring heat by circulating fluid through a closed system — boilers, pressure vessels, refrigeration equipment in connection with chilled water systems, all steam piping, and hot or chilled water piping with controls and accessories — as part of a system whose primary purpose is comfort, meaning at least 51 percent of capacity on an annual average dedicated to comfort; low- and high-pressure systems and associated gas lines are included. The 51 percent line is the kind of definitional edge the general-requirements portion of the examination exists to test.

The journeyperson frame applies to the whole breadth at once. The holder works under the supervision of a master licensed in the discipline of the work being performed — for mechanical-scope work, a master mechanical licensee — supervises apprentices only within the disciplines the journeyperson holds and only for the same licensed contractor, and must not knowingly work for an unlicensed contractor. The business prohibitions are unchanged by breadth: no engaging in the business without a master actively in charge, no sole-proprietor practice without personally holding a master license, no service as master of record, and no contractor role. The electrical boundary is equally unchanged: exemption from a chapter 103 special electrician’s license only to disconnect and reconnect existing air conditioning and refrigeration systems. Chapter 105 preempts local licensing, with local permit and inspection fees preserved. Two specialty sublicenses — Service Technician HVAC and Hearth Systems — sit under a mechanical or HVAC-refrigeration license, and the parent license holder need not obtain a sublicense of it.

The two routes, compared honestly

The direct route is examination: Board candidate approval, the Journeyperson Mechanical with Gas sitting at Kirkwood, a passing score under the Board’s general rule, and the separate post-examination licensure application. It suits the candidate whose record is a single broad apprenticeship and who holds no component journeyperson license.

The combination route is qualification by components. Iowa Code section 105.18(2)(b)(3) provides that a person who has passed both the HVAC-refrigeration and the hydronic journeyperson examinations is qualified for the mechanical license without taking the mechanical examination. The master tier carries an analogue of the same provision. For a licensee already holding both component licenses, the election mechanics run at renewal: the holder of HVAC-refrigeration and hydronic licenses at the same level may combine them into a single Mechanical license during the renewal window, May 1 through June 30 of the period’s final year, meeting a 14-hour continuing education requirement to combine and following the single-license eight-hour requirement thereafter, with no combining charge at renewal.

Three consequences follow. First, the Mechanical examination is the direct route, not the only route — no accurate account of this license says every holder passed it. Second, the routes are not interchangeable mid-stream: the combination rests on two passed component examinations at the same level, so a candidate holding only one component license faces a genuine choice between the second component examination and the Mechanical sitting, judged against the outlines of each. Third, the combined holder’s ongoing burden is lighter: one license at the eight-hour education level, in place of two licenses whose uncombined total is 14 hours. This guide prepares candidates for the direct route while keeping the combination route visible throughout, because the administration content assumes candidates understand the system they are entering, not merely the paper in front of them.

The route, step by step — direct route

Step one — build the apprenticeship record. Licensure in this discipline requires at least four years of practical experience as an apprentice, which since January 1, 2010 must be a registered apprenticeship training program. No Mechanical-specific variation of that gate appears in the sources: the journeyperson gate is discipline-general, and no separate Mechanical year-count exists to be found. The apprentice is Board-licensed and enrolled in a registered program, eligible from 18 with a high school diploma or equivalent; the registered ratio is one apprentice to one journeyperson absent a collective bargaining agreement; helper experience is not practical experience.

Step two — clear the examination gate. A candidate may sit on completion of a minimum of 36 months in a registered apprenticeship program, or on at least four years of pre-2010 experience, with a notarized Affidavit of Employment for that basis.

Step three — obtain Board approval. Submit the State of Iowa Examination Candidate Application, online or on paper, with the $35 candidate fee per trade examination, at least 15 business days ahead. Board staff verify and issue an Exam Approval Letter with Kirkwood scheduling instructions. Approval lasts one year, with as many attempts as necessary inside it at a further examination fee each; after the year, a fresh application and fee. Criminal-history documentation duties attach to applications, and an eligibility determination may be petitioned for in advance.

Step four — sit and pass. The sitting is described in full below; the score appears on screen at the end.

Step five — apply for the license. Passing issues nothing by itself. The separate post-examination application follows, unprocessed for an apprenticeship-route applicant until the Office of Apprenticeship certificate of completion has issued and the program has been completed, with the initial fee prorated for a partial period — and a passing score expires if licensure is not applied for within two years of notification.

The outline in full

Kirkwood prints one outline for the Mechanical examinations, shared between the journeyperson and master levels, listing all topics covered, the approximate percentage per topic, the total number of questions, and the maximum time allowed. The totals differ by level — this license’s sitting is 75 questions in two hours. The seven areas follow.

General Requirements, Definitions, Testing — 22 percent

The largest block is the discipline’s frame: the mechanical code’s general requirements, its definitions, and its testing provisions. For a license whose scope is assembled from four statutory definitions and a code adopted in a specific, amended form, this block is where breadth is examined as knowledge — what the terms mean, where the requirements attach, and how systems are tested. It rewards candidates who read definitions as operative text.

Heating, Refrigeration, and Hydronic Systems — 20 percent

The systems block gathers the equipment heart of three of the four disciplines into one area. Its examination source is the mechanical code alone: this sitting lists no refrigeration textbook, so refrigeration systems are examined as the code treats them, alongside heating and hydronic systems. Candidates arriving from HVAC/Refrigeration preparation will feel the shift most here — the same subject matter, a different source book, and hydronic content at full weight rather than at the edges.

Exhaust and Ventilation Systems — 15 percent

Ventilation is core mechanical work under this license — it sits inside the sheet metal definition itself — and the outline weights it accordingly. Together with the duct and chimney areas, the air-side provisions account for more of this paper than the systems block does.

Chimneys and Vents — 14 percent

A standalone block with no counterpart of this size on the HVAC/Refrigeration outline, covering the venting of appliances through chimneys and vent systems under the mechanical code — a clear signal that this paper examines the whole mechanical installation, including parts a refrigeration-focused candidate rarely touches.

Duct Systems — 12 percent

The duct block examines the distribution systems the sheet metal component of the license exists to build: construction, sizing concepts, and installation requirements under the code, as their own area rather than folded into a general installation category.

Fuel Supply System — 10 percent

The fuel block keys to NFPA 54, 2024 edition, the second of this examination’s two references. At one question in ten it is a smaller share than the gas content on the HVAC/Refrigeration paper, but it is examined from a separate book, and the candidate must move between the code and the fuel gas standard fluently.

Combustion Air — 7 percent

The smallest block is a precise one: the air supply provisions combustion depends on. Small blocks are where weighted papers are quietly decided — seven percent of 75 questions is a handful of items a prepared candidate collects and an unprepared one donates.

Two books: the reference discipline

The examination allows two references: the 2024 International Mechanical Code and the 2024 edition of NFPA 54. That is the complete list for both Mechanical levels, and it is the most consequential factual difference between this program and its HVAC/Refrigeration sibling: Modern Refrigeration and Air Conditioning is not a reference for this examination, in any edition, although it is a listed reference for both HVAC/Refrigeration levels. Study built on that text does not build familiarity with the book the candidate will actually open in the room, and in an open-book sitting, familiarity with the physical reference — its chapter order, its index, its tables — is a measurable part of performance. Kirkwood’s allowance that a book physically brought may be from another edition applies to the listed titles; the questions remain based on the listed editions.

Tested and adopted: two layers, one edition

The tested layer is the two-book reference set above. The adopted layer is the State Mechanical Code, adopting Sections 101–102 and Chapters 2–15 of the 2024 International Mechanical Code, effective March 26, 2025. The layers agree — tested equals adopted — and the agreement was reached by a jump: the prior state code rested on the 2018 edition, and no 2021 edition was ever adopted in Iowa. Material built on the intervening edition describes a code Iowa skipped. On fuel gas the position is categorical: Iowa does not adopt the International Fuel Gas Code. Iowa amendments replace references to it with NFPA 54 in its current edition, NFPA 58, chapter 226 of Title 661, and the state plumbing code — the same NFPA 54 family the examination lists, consistent with its “with Gas” title. The Board must adopt the current code version within six months of release. Local jurisdictions need not adopt the state codes by ordinance and may be more restrictive where they do, so field obligations can exceed the state floor even though the examination keys to the state position.

The sitting itself

The examination is written and proctored, in person or online, offered periodically at rotating Iowa sites, and administered by Kirkwood Community College, the Board’s approved examination provider. Registration runs through Kirkwood by telephone, payable by major card; the candidate receives a receipt and a confirmation email with test-site contact information, selects a site and contacts it directly to schedule, and receives login credentials by email within the hour. The examination fee is $119 per attempt, paid to Kirkwood, non-refundable and non-transferable. A candidate who does not pass registers and pays again within the Board’s one-year approval window; no maximum-attempts cap is published, and the statute provides that an applicant who fails shall be allowed to retake at a future scheduled time.

Room rules are the standard Iowa discipline. Approved references only, bound or loose-leaf; photocopies barred; no handwritten or additional notes in the books, with anything written in during the sitting confiscated; pre-arrival highlighting and permanent tabbing allowed, removable sticky notes barred; references checked before and after and never shared; scratch paper provided and confiscated. A battery-operated, nonprogrammable calculator without storage or printing capability is allowed, with an architect’s scale or rule, magnifying glasses, and a translation dictionary if needed. Electronic devices stay out of the testing area; leaving the room means signing out and in, with time lost. Arrival is at least 30 minutes early, with photo identification bearing a signature and exactly matching the registration name. The score displays on screen at the end; results are confidential; the examination is not subject to review, although failed sections are identified on request; appeals go to Kirkwood in writing, with faxed appeals not accepted; disability accommodations carry no additional charge, with documentation due at least two weeks before the date. No practical, drawing, or performance component forms part of this examination.

The pass standard requires one precise statement, because this examination carries no Mechanical-specific pass printing of its own. The standard is the Board’s general examination rule at 481 IAC 429.6(2)(d) — “A score of 75 percent or better is considered passing” — which by its terms governs each Board examination, with Kirkwood stating that a score of 75 percent or above is required to pass each exam. Recorded in that form, the standard is this examination’s own, not a figure borrowed from any other license’s materials.

Fees in full, kept apart

Approval, attempt, license: three instruments, three moments, never one sum. The Board candidate fee is $35 per trade examination, paid with the candidate application. The Kirkwood examination fee is $119 per attempt, paid to Kirkwood at registration, applying to the direct route’s sittings; a candidate who qualifies by combination takes no Mechanical sitting and pays no Mechanical examination fee. The Board license fee is $180 for the three-year period, initial and renewal the same, nonrefundable, with initial proration at one-sixth per six-month period. Smaller Board charges attach to other transactions, and multiple active licenses bought in a single transaction receive the fee rule’s combined reduction, with waivers for qualifying low-income first-time applicants and qualifying discharged service members. The combining election itself carries no charge at renewal; its cost condition is educational, the 14-hour combining requirement, not financial.

After the sitting: the credential and its clock

The triennial clock is fixed: three-year periods expiring June 30 every three years regardless of issue date, the current period running July 1, 2026 through June 30, 2029. Renewal opens May 1 of the third year, due at least 30 days before expiration. The lapse ladder runs: a one-month grace period without a late fee; August renewal at a $60 late fee; renewal after August through the following June 30 at a $100 late fee; the renewal fee itself due in each case, without examination. The license remains valid for practice up to two months past expiration, then lapses. Reinstatement after a lapse of more than one year requires retaking and passing the applicable examination, or completing all continuing education for each missed period, at the full fee with no proration — the rule states the requirement in those general terms, and no source pulled specifies a combination-route gloss for a holder who never took the Mechanical examination, so none is offered here. Inactive status must be renewed, is not valid for practice, reactivates on written request with the active fee, and remains subject to continuing education.

Continuing education for this single combined license is eight hours per period: two of safety, two of code on the Iowa mechanical code, and four in the discipline. An hour is at least 50 minutes; courses and instructors are Board-approved; a course counts once per period however often attended; at most half the hours may be online; records are produced within 30 calendar days of a compliance request, with a 120-day cure for a good-faith deficiency. The 14-hour figure belongs to two other situations only — multiple mechanical licenses held uncombined, and the combining period — and a plumbing license held alongside raises the total to 16 hours. Alternative pathways hold their discipline: licensure without examination runs only under a reciprocity agreement, and the Board’s only published agreement, from May 2016, covers plumbing licenses — no Mechanical reciprocity is published. Licensure by verification still requires proof of passing the applicable Iowa examination; licensure by work experience requires at least three years of full-time work, at least 1,700 hours in a year, within the prior four years, plus any necessary examinations. A date-bound military waiver covering deployment inside a specific 2008–2009 window exists in the statute and is not generalised. Federal refrigerant-handling certification is not a condition of this license in any source pulled.

A study plan built on how this examination is actually put together

Plan for breadth under a clock. First, the mechanical code as one instrument — its general requirements, definitions, and testing provisions are both the largest outline block and the lens for every other block, so code navigation drills come before content drills. Second, the systems block in the code’s own terms, re-sourcing refrigeration knowledge away from textbook habits toward code provisions, with hydronic systems at full weight. Third, the air side as a unit — exhaust and ventilation, duct systems, and chimneys and vents together outweigh the systems block, and they are where single-trade candidates are thinnest. Fourth, NFPA 54 fuel supply and the combustion air provisions, small blocks studied to precision. Fifth, the route itself — the combination comparison, the approval window, the separate licensure step — because choosing the wrong route costs more than any single question. Timed mixed practice across all seven areas, in outline proportion, closes the plan.

The errors this examination is built to catch

Importing the HVAC/Refrigeration outline — different percentages, different architecture, a different paper. Importing its reference list — three books where this sitting allows two, and the missing one is the refrigeration text. Importing plumbing examination figures, which describe no Mechanical sitting. Assuming every Mechanical licensee passed this examination — the combination route is statutory. Studying the skipped code edition, or fuel gas from a code Iowa has never adopted. Reading breadth as permission — the license spans four disciplines and still stops at the electrical boundary, the supervision line, and the business line. Merging the fees, or skipping the licensure step after a pass, with its two-year expiry. Each error is a layer error: the right fact, filed under the wrong license, book, edition, or step.

Iowa in one view

Iowa in one view is a state that licenses breadth deliberately. The Mechanical journeyperson license gathers four defined disciplines into one credential, offers two honest routes into it — a broad systems examination in two books, or two narrower examinations combined by statute — and then holds the combined holder to the same supervision discipline, the same triennial clock, and the same eight-hour education measure as any single-discipline journeyperson. Its traps are all acts of transfer: from the sibling license, from the skipped code edition, from the unadopted fuel gas code, from the textbook that is not on the list. The candidate who resists transfer is studying the license Iowa actually issues. The companion program page at /iowa-journeyperson-mechanical-exam-prep/ summarises the credential and both routes; this guide is the full account.

Frequently asked questions

Does this guide’s examination have its own pass line in the provider’s outline?

No Mechanical-specific pass printing appears in the outline material. The standard is the Board’s general examination rule at 481 IAC 429.6(2)(d) — “A score of 75 percent or better is considered passing” — which governs each Board examination by its own terms, with Kirkwood stating the same standard for each exam.

Why is there no refrigeration textbook on the reference list?

Because Kirkwood’s Mechanical reference list contains two titles only: the 2024 International Mechanical Code and the 2024 edition of NFPA 54. The refrigeration textbook is a reference for the HVAC/Refrigeration examinations, not for either Mechanical level.

Can a candidate qualify without this examination?

Yes. Passing both the HVAC-refrigeration and hydronic journeyperson examinations qualifies a person for the mechanical license without the mechanical examination, under Iowa Code section 105.18(2)(b)(3).

Which examination does a lapsed combination-route holder retake?

The rule requires retaking and passing the applicable licensing examination after a lapse of more than one year, or completing all missed continuing education. No source pulled specifies a combination-route answer, and this guide offers none.

Is there a practical component?

No. The examination is written and proctored, in person or online, with no hands-on, drawing, or performance component in the rule, the Board’s pages, or the provider’s documentation.

When does enrollment open for the PassProfessor program?

The program is in the works and enrollment is not yet open. Leave an email address on this page and PassProfessor will write to you when the program is ready — and only about this program.