Florida’s Class B Air-Conditioning Contractor is a certified Division II category under section 489.105(3)(g), Florida Statutes, issued through the Construction Industry Licensing Board within the Department of Business and Professional Regulation. Its services are limited to 25 tons of cooling and 500,000 Btu of heating in any one system, and its Trade Knowledge examination — Air Conditioning “B” — carries 80 scored questions in 5 hours of Daily CBT, with the published passing standard stated in the Candidate Information Booklet’s own form: Passing score: 70%. This guide works through the credential, the examination, and the route between them; the companion program page at /florida-class-b-air-conditioning-contractor-exam-prep/ carries the program itself.
This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.
The credential at a glance
| Item | Verified position |
|---|---|
| Program | Florida Class B Air-Conditioning Contractor — the Air Conditioning “B” Trade Knowledge examination |
| Regulator | Construction Industry Licensing Board (CILB), Department of Business and Professional Regulation (DBPR) |
| Statutory category | Section 489.105(3)(g), Florida Statutes — Division II, certified |
| Scope cap | Limited to 25 tons of cooling and 500,000 Btu of heating in any one system |
| Scope delta | No boiler and unfired pressure vessel systems; no pressure and process piping; no pneumatic control piping |
| Examination structure | Two examinations: Trade Knowledge and Business and Finance (Business and Finance is structure only in this guide) |
| Trade Knowledge examination | 80 scored questions / 5 hours, Daily CBT; multiple choice, four alternatives, equally weighted |
| Passing standard | Passing score: 70% — percentage scores, not rounded |
| Book status | Open book, controlled references from the approved list; Architect’s Scale (including 1/4″ and 1/8″) required in the center |
| Code layers | Tested and adopted coincide for 2026: 2023 Florida Building Code (8th Edition) |
| Score validity | A passing grade is valid for four years from Board approval of the successful-candidates list |
| Administrator note | PassProfessor is independent and is not affiliated with the Construction Industry Licensing Board or DBPR |
Florida certification is a statewide instrument: a certified contractor holds a certificate of competency issued by the department and may contract in any jurisdiction in the state without fulfilling that jurisdiction’s competency requirements. Class B is the capped member of the certified air-conditioning pair. This guide is organised around the cap and its consequences, because nearly everything distinctive about this credential — its scope sentence, its examination’s size and weights, its place on the ladder — follows from licensing a limited class alongside an unlimited one.
The cap, read carefully
Class B services are limited to 25 tons of cooling and 500,000 Btu of heating in any one system. Three features of that sentence carry weight. First, the measure is per system — “in any one system” — so the question on any job is the size of the system being installed, maintained, repaired, fabricated, altered, extended, or designed, not the size of the building, the contract, or the contractor’s year. Second, the cap runs on both sides of the work: cooling capacity in tons and heating capacity in Btu, and a system beyond either measure is beyond this classification. Third, the cap is a scope limit, not an examination topic: it defines the license the examination certifies, and the Class A form’s experience areas — which ask about systems in excess of exactly these figures — show the Board treating the same line from the other side.
Within the cap, the work verbs and the systems language track Class A: install, maintain, repair, fabricate, alter, extend, or design, if not prohibited by law, central air-conditioning, refrigeration, heating, and ventilating systems, including duct work in connection with a complete system only to the extent such duct work is performed by the contractor as necessary to complete an air-distribution system being installed under this classification, and any duct cleaning and equipment sanitizing that requires at least a partial disassembling of the system. The duct sentence is slightly narrower than the Class A sentence — it ties the duct work to a system being installed under this classification — and candidates should notice the qualifier rather than read the two definitions as interchangeable.
The piping delta: three absences
The Class B scope covers piping and insulation of pipes, vessels, and ducts only. Set beside the Class A and Mechanical definitions, three elements are absent, and each absence is a scope boundary a holder must be able to draw:
Boiler and unfired pressure vessel systems. Present in the Class A definition and in the Mechanical definition; absent here. Boiler work is outside this classification regardless of the size of the air-conditioning system on the same project.
Pressure and process piping. Present in both other definitions; absent here. The Class B piping sentence grants piping generally and insulation, and stops there.
Pneumatic control piping. Present in both other definitions; absent here. Control work within this classification runs through the electrical allowances — low-voltage HVAC control wiring — not through a pneumatic piping grant.
Everything else in the scope paragraph is verified as the same as Class A, and this guide states it as shared ground: the electrical allowances (replace, disconnect, or reconnect power wiring on the line or load side of the dedicated existing electrical disconnect switch on single-phase systems; repair or replace power wiring, disconnects, breakers, or fuses for dedicated HVAC circuits with proper use of a circuit breaker lock; install, disconnect, and reconnect low-voltage HVAC control wiring); the condensate-drain allowance to an existing safe waste or other approved disposal other than a direct connection to a sanitary system; excavation work incidental to the scope; the exclusions (liquefied petroleum or natural gas fuel lines within buildings except disconnecting and reconnecting changeouts of appliances within buildings, potable water lines or connections thereto, sanitary sewer lines, swimming pool piping and filters, and electrical power wiring); and the permission to test and evaluate systems including duct work, for which no mandatory licensing requirement is established. Section 489.113(3) applies: a contractor shall subcontract all electrical, mechanical, plumbing, roofing, sheet metal, swimming pool, and air-conditioning work unless the contractor holds a state certificate or registration in the respective trade category.
The content weights, and the five differences
Rule 61G4-16.001(6)(b) publishes the Class B weights across nine areas. Installation of Refrigeration and HVAC Systems leads at 22 percent. Installation of Refrigeration and HVAC Equipment and Components and Maintenance Service of Refrigeration and HVAC Systems each carry 14 percent. Pre-installation carries 12 percent. Maintenance Analysis of Refrigeration and HVAC Systems and Safety and Equipment each carry 10 percent. Sheet Metal Ducts carries 9 percent, Energy Management 5 percent, and Indoor Air Quality 4 percent. The areas sum to 100 percent.
Against the Class A paper, five areas differ. Pre-installation is 12 percent here against 14 percent there. Installation of Refrigeration and HVAC Systems is 22 against 23. Maintenance Analysis is 10 against 9. Safety and Equipment is 10 against 9. Indoor Air Quality is 4 against 3. The remaining four areas — Sheet Metal Ducts, Equipment and Components installation, Maintenance Service, and Energy Management — are weighted identically on both papers. The redistribution is small in each area and consistent in direction: the capped class’s paper gives a point or two less to pre-installation and systems installation, and a point or two more to maintenance analysis, safety, and indoor air quality. Neither air-conditioning paper carries an Excavating area or separate mechanical systems and equipment areas; those are Mechanical-examination features. A study plan imported from Class A without adjustment would be wrong in five areas, which is why this guide treats the Class B weights as a distinct document rather than a footnote to the unlimited class.
The route, step by step
Step one — qualify under section 489.111. The applicant applies to the department in writing, is 18 years of age, is of good moral character — with refusal on that ground permitted only where there is a substantial connection to the professional responsibilities of a certified contractor, supported by clear and convincing evidence — submits electronic fingerprints, and meets one of the experience and education criteria: a baccalaureate degree from an accredited four-year college in the appropriate field of engineering, architecture, or building construction plus one year of proven experience in the category sought; or at least four years of active experience as a skilled worker able to command the rate of a mechanic in the trade, or as a foreman in charge of a group of workers, provided at least one year is as a foreman; or one of the three combination routes, each requiring the foreman year — one year as foreman plus three years of accredited college-level credits; one year as skilled worker plus one year as foreman plus two years of credits; or two years as skilled worker plus one year as foreman plus one year of credits — with full-time equivalency at a minimum of 2,000 person-hours per year, and junior and community college courses counting as accredited college-level courses.
Step two — or arrive by the ladder. An active certified Class C contractor with a minimum of three years of proven experience in the Class C classification is eligible to take the Class B examination under section 489.111(2)(c)5. Class C, as context only, is limited to servicing of air-conditioning, heating, and refrigeration systems and is grandfathered to persons registered or certified as Class C on October 1, 1988. The degree provision offers a different kind of shortcut: an applicant with a baccalaureate degree in building construction, or a board-approved related degree, and a grade point average of 3.0 or higher is only required to take and pass the Business and Finance portion of the examination.
Step three — register with Professional Testing, Inc. PTI registers candidates and develops and scores the CILB professional examinations; candidates apply directly with PTI.
Step four — schedule and sit with Pearson VUE. After PTI approval, Pearson VUE schedules, administers, scores, and reports the sitting: 80 scored questions, 5 hours, Daily CBT. Appointments are changed or cancelled through Pearson VUE two days prior to the scheduled appointment; cancelling later or missing the examination may result in forfeiting examination fees.
Step five — pass both examinations, then complete issuance. Passing the examination alone does not qualify a person for licensure. The application for initial issuance follows passing, with the financial-responsibility gates described below. A passing grade remains valid for four years from the date the list of successful candidates is approved by the Board.
After a failed sitting. A failing candidate may review only the questions answered incorrectly on the most recent examination, on request within 21 days of the examination date, under examination security conditions at a Pearson VUE testing center.
The ladder in both directions
Class B is the middle rung of the air-conditioning ladder, and both of its steps are statutory. Inbound: Class C to Class B at three years of proven experience in the Class C classification. Outbound: Class B to Class A at one year of proven experience in the Class B classification — the same provision, section 489.111(2)(c)5, also lets a Class C contractor reach Class A directly at four years. The one-year outbound step is the shortest upgrade in the family, and it is coherent with the verified sameness of the two trade papers’ foundations: identical reference lists, identical code layers, identical passing standard and reference discipline. What the upgrade candidate faces is not a different library but a larger paper — 130 scored questions in 7.5 hours against 80 in 5 — examining an uncapped scope that adds the boiler, pressure and process piping, and pneumatic control piping ground this classification does not carry. Planning for Class B with the upgrade in view is legitimate strategy; treating Class B scope as if it already included the Class A ground is not, and the distinction is exactly the kind the scope items on both papers are built to test.
The sitting itself: format and reference discipline
All construction examinations except the Plumbing Contractor examination are administered in CBT format, and the Air B paper runs as Daily CBT. All questions are multiple choice with four alternative answers, equally weighted, and knowledge of basic mathematics is required for each part. Scores are reported as percentage scores; the minimum percentage needed to pass is seventy percent, and scores are not rounded to the nearest percent. The passing standard and its published form are identical for Class A and Class B. An examination may contain a small number of pilot questions; they are not counted in computing scores, additional time is given for them, and they are not identified to the candidate. No fixed pilot count for this examination exists in the sourced record, and this guide prints none.
The reference discipline matches Class A in every particular. Only materials and books on the approved reference list for the candidate’s examination may be brought to the test center. Books must remain as published; underlining with pen or highlighter is permitted. Only original-edition materials may be used, except references indicated as PDF files, whose printed copies must be bound without staples and remain bound during the examination. Permanently attached tabs with only normal chapter or page headings are permitted; removable tabs and sticky notes are prohibited. Handwritten and typewritten notes are not allowed, and candidates may not make marks in references during the examination. Photocopies are not allowed without prior written authorization. Answers are based on the editions listed; earlier or later editions may be brought at the candidate’s own risk, and only one copy of each reference is permitted. Class B candidates must bring an Architect’s Scale, including 1/4″ and 1/8″ — the same requirement as Class A, and a supply rule rather than a practical component; no hands-on practical for this examination appears in the sourced record.
Tested and adopted: two layers that coincide
The tested layer is verified in full: the DBPR Reference List for the Air B CBT examination, valid January 2026 through December 2026, is identical in titles and editions to the Air A list — headed by Florida Building Code – Mechanical, 2023 and Florida Building Code – Energy Conservation, 2023, and carrying the same NFPA, SMACNA, textbook, Contractors Manual, and OSHA titles in the same editions. The reference layer does not differ between the classes; the differences are the count, the duration, the weights, and the scope. The adopted layer is the field standard: the 8th Edition (2023) Florida Building Code, Mechanical, effective December 31, 2023, in force until the 9th Edition takes effect, built on the 2021 International Mechanical Code with Florida-specific amendments, over the 7th Edition (2020) Florida Building Code, Mechanical as its base code. The layers coincide at the 2023 Florida Building Code for the 2026 window, and this guide states them as separate layers that coincide. Answers key to the Florida Building Code text, not to bare IMC 2021, wherever the two differ. No claim is made here about a 2027 reference list or an examination re-key date; the sourced record states neither.
The second examination, as a boundary only
Certification requires the Business and Finance examination alongside the Trade Knowledge examination: 120 scored questions, 6.5 hours, Daily CBT, within the same PTI and Pearson VUE system. This guide records that structure and builds no content for it, because the Business and Finance bank is a shared asset across Florida’s Division II categories. The Business and Finance relationship does not differ between Class A and Class B — same examination, same structure, same rules. Its two boundary mechanics apply here in full: a passing candidate applying for examination in an additional category may be exempt from retaking the Business and Finance portion, and the degree provision waives the trade examination while leaving the Business and Finance examination required.
Financial responsibility, insurance, renewal — and an honest note on fees
The issuance gates match the family pattern. Section 489.115(5) requires the affidavit of workers’ compensation, public liability, and property damage insurance in board-rule amounts, and a credit report from a nationally recognized agency at initial issuance. Rule 61G4-15.006 names the denial grounds: failure to provide a current consumer credit report disclosing no unsatisfied judgments or liens, and failure to provide proof of a FICO-derived credit score of 660 or higher, with completion of a 14-hour board-approved financial responsibility course as the only cure below 660 under the current rule. The insurance table at Rule 61G4-15.003 lists the air-conditioning classification at liability coverage of 100,000 dollars and property damage coverage of 25,000 dollars — a single air-conditioning row covering the classification family as printed — and insurance must at all times be carried in the name of the licensee. Workers’ compensation coverage is a condition precedent to issuance or renewal under section 489.114.
One fee position must be stated plainly, because secondary sources blur it: no fee figure for this credential is verified in the sourced record. No examination fee, no initial application fee, and no renewal fee dollar for the Class B classification is stated in this guide, and the application schedule verified for the Class A form must not be carried onto this credential — it belongs to that form only. Candidates budgeting the route should hold the fee layers as unstated here and verify them on the current Class B application form rather than borrow figures across the family.
Continuing education is 14 hours per biennium — at least 14 classroom hours of at least 50 minutes each, or interactive distance learning hours, from a Board-approved provider — with one hour required in each of a specialized or advanced module course, workplace safety, business practices, workers’ compensation, and laws and rules regulating the construction industry, and the remaining nine hours in listed or general topics. The wind-mitigation hour does not apply to this classification. No hours are required for the year of initial issuance; a certificate obtained more than 12 months before the end of a biennial period carries seven hours at the first renewal; a person holding more than one certificate completes the requirement once per period; no continuing education is required while a license is inactive, and reactivation requires proof of 14 hours for the previous biennium. Renewal is biennial, on August 31 of every even-numbered year.
A study plan for the capped class
First, learn the definition as a boundary, not a summary. The cap per system, the duct-work qualifier, and the three piping absences are the credential. Be able to sort described work into inside and outside this classification, stating which line of section 489.105(3)(g) decides it.
Second, weight the paper as published. Installation of Refrigeration and HVAC Systems at 22 percent leads; equipment and components installation and maintenance service at 14 percent each follow; maintenance analysis and safety and equipment at 10 percent each outrank their Class A weights and deserve the extra time the rule gives them.
Third, study the same books differently. The reference list is identical to Class A’s, so the library is not the work — the pacing is. Eighty scored questions in 5 hours is a different sitting rhythm from the unlimited paper, and timed practice should be built to this paper’s count and clock.
Fourth, rehearse the room. Published-condition references, permanent tabs only, no notes, no marking during the sitting, one copy of each reference, Architect’s Scale in hand: practise locating answers under those rules, because the center enforces them exactly.
Fifth, keep the ladder in view without borrowing its scope. The one-year step to Class A rewards a Class B holder who documents experience carefully from the start. It confers nothing until the Class A examination is passed, and work beyond the cap or inside the three absent piping areas belongs, until then, to holders of the classifications that carry it.
The companion program page for this credential is the Florida Class B Air-Conditioning Contractor program page at /florida-class-b-air-conditioning-contractor-exam-prep/.
Frequently asked questions
What exactly does the Class B cap measure?
The system. Class B services are limited to 25 tons of cooling and 500,000 Btu of heating in any one system; a system beyond either measure is beyond this classification, whatever the size of the building or the contract.
Which scope elements does Class B lack?
Boiler and unfired pressure vessel systems, pressure and process piping, and pneumatic control piping — all present in the Class A and Mechanical definitions, all absent from the Class B definition, which covers piping and insulation of pipes, vessels, and ducts only.
How is the Class B examination weighted?
Installation of Refrigeration and HVAC Systems 22 percent; Installation of Refrigeration and HVAC Equipment and Components and Maintenance Service at 14 percent each; Pre-installation 12 percent; Maintenance Analysis and Safety and Equipment at 10 percent each; Sheet Metal Ducts 9 percent; Energy Management 5 percent; Indoor Air Quality 4 percent — under Rule 61G4-16.001(6)(b).
What is the passing standard, exactly as published?
Passing score: 70%. Scores are reported as percentage scores and are not rounded. The form is identical for Class A and Class B.
Are pilot questions part of the 80?
The 80 are the scored questions. A small number of pilot questions may also appear; they are not counted in computing scores, additional time is given for them, and they are not identified to the candidate. No fixed pilot count exists in the sourced record for this examination.
Do Class A and Class B use the same reference list?
Yes. The Air A and Air B Trade Knowledge reference lists are identical in titles and editions for the January through December 2026 window, headed by the two 2023 Florida Building Code volumes. The examinations differ in count, duration, and weights — not in their books.
How does the ladder run through Class B?
Inbound, an active certified Class C contractor with three years of proven experience in the classification may take the Class B examination. Outbound, an active certified Class B contractor with one year of proven experience may take the Class A examination.
What fees does this guide state for Class B?
None, deliberately. No examination, application, or renewal fee figure for this credential is verified in the sourced record, and the application schedule verified for the Class A form belongs to that form only.
What financial gates stand between passing and issuance?
An insurance affidavit, a credit report from a nationally recognized agency, proof of a FICO-derived credit score of 660 or higher — or, below 660, completion of a 14-hour board-approved financial responsibility course — and workers’ compensation coverage as a condition precedent. The insurance table lists the air-conditioning classification at liability coverage of 100,000 dollars and property damage coverage of 25,000 dollars, carried in the licensee’s name.
How much continuing education does the credential require?
Fourteen hours per biennium from a Board-approved provider, with one hour each in a specialized or advanced module, workplace safety, business practices, workers’ compensation, and laws and rules, and nine further hours in listed or general topics. Renewal falls on August 31 of every even-numbered year.
Is there a hands-on practical on this examination?
No practical component appears in the sourced record. The Architect’s Scale requirement is a bring-to-the-center supply rule, not a practical component.
Is PassProfessor affiliated with the Construction Industry Licensing Board?
No. PassProfessor is an independent preparation provider, not affiliated with the Board or with DBPR. The Board alone certifies; candidates register through Professional Testing, Inc. and schedule with Pearson VUE.
When does enrollment open for the PassProfessor program?
The program is in the works and enrollment is not yet open. Leave an email address on this page and PassProfessor will write to you when the program is ready — and only about this program.
