The D-2 Limited Warm Air, Air Conditioning and Refrigeration Journeyperson license is Connecticut’s limited journeyperson credential for warm air, air conditioning and refrigeration systems — including the piping that conveys their heating or cooling media — issued by the Department of Consumer Protection under Chapter 393 and exercised while in the employ of a licensed contractor. Its gas work is included; its oil-burner work is excluded at any size. This guide works through the boundary in both directions, the ladder beneath the license, and the route to it. The companion program page is at /connecticut-d-2-limited-warm-air-air-conditioning-and-refrigeration-journeyperson-exam-prep/.
This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.
How to use this guide, and what it deliberately does
Connecticut publishes a great deal about this credential: its scope sentence, its inclusions, its exclusion, its ladder, its qualification route, and its fees at the Department layer. This guide is built entirely from that published substance, organised the way this license is actually used — boundary first, because a limited license is a boundary with a workforce inside it, then the ladder and qualification, then the application, then the license held over time. Where the Department’s published materials end, this guide ends with them. A candidate who needs a position the Department has not published for this license should take the question to the Department — not to a secondary summary, and not to an assumption carried over from the unlimited license, from another limited license with a different fuel posture, or from another state.
That restraint matters doubly for a limited license. Every error this credential invites is an act of borrowing: borrowing the unlimited scope’s breadth, borrowing a neighbouring license’s gas rule, borrowing another trade’s renewal habits. The guide’s method is the opposite: it states this license’s own published terms, in this license’s own words, and flags each place where a sibling license’s terms differ.
Inside the boundary: systems, verbs, and connective work
The scope sentence grants the installation, repair, replacement, maintenance or alteration of any warm air, air conditioning and refrigeration system. Break it into its working parts, because candidates prepare better against parts than against a blur.
The systems first. Warm air systems — the forced-air heating side of the trade. Air conditioning systems — the comfort-cooling side. Refrigeration systems — the refrigeration side of the limited field. The three together are the license’s territory, and each is granted in full working form: the verbs that follow apply to all three.
The verbs next: installation, repair, replacement, maintenance, alteration. The set is complete across a system’s life. A D-2 holder installs the system, maintains it, repairs it, alters it, and replaces it. No verb in the ordinary working life of these systems is held back for another tier, which is why this license, though limited in territory, is a full working license inside its territory.
The connective work completes the grant: including necessary piping for the conveyance of heating or cooling media and associated pumping equipment. Systems do not heat or cool buildings by existing; media must move between equipment and the spaces served, and pumps must move it. Connecticut writes that movement into the license expressly. When you sort a task, ask first whether it is work on one of the three system families, and then whether connective piping or pumping work is part of making that system work — the scope answers the second question yes within the first one’s territory.
Finally, the sheet metal inclusion, quoted with its qualifier intact: the license includes sheet metal work as it pertains to the credential’s limitations. Ductwork and sheet metal work belonging to the systems this license covers ride inside the boundary; sheet metal work that does not pertain to those limitations does not ride in on this clause. The qualifier is not fine print; it is the inclusion’s actual shape.
The gas inclusion, stated plainly
LP gas supplied by gas containers and natural gas piping are included in this license. Approved gas appliances, gas utilization equipment and accessories are included as well. That is the whole posture, and it deserves to be learned as a posture rather than as a footnote, because it decides real dispatches: the gas-fired warm-air installation, the gas appliance set within this license’s systems, the utilization equipment that completes them — inside the boundary, piping and appliances together.
Now set the posture beside its contrast, because Connecticut drew this line deliberately and in opposite directions within one family. The state’s limited cooling journeyperson license excludes gas work from its scope altogether — LP gas, natural gas and oil-burner servicing are all outside that license. Two limited licenses, one trade family, opposite gas postures. There is no family rule about gas to learn; the task is to learn each license’s own rule and never let one answer for the other. For the D-2 the answer is inclusion, and confusing the two postures is the single easiest boundary error this family offers.
Note also where the gas inclusion lives in the Department’s materials: on the Department’s current scope pages for this license family, which are where this guide keys the limited licenses’ boundary items. Scope questions should be answered from the Department’s current published scope for the credential itself, rather than from older compilations of the family’s regulations, which do not carry the current boundary statements in full.
The oil-burner exclusion, at any size
The exclusion is one sentence and it is total: this license does not include the installation or servicing of oil burners of any size.
Unpack its three closures, because each closes a door candidates test. Installation is outside — a D-2 holder does not put an oil burner in. Servicing is outside — a D-2 holder does not maintain, repair or attend one in service, either; the exclusion is not an installation-only rule that leaves the service van lawful. And the size phrase closes the scale argument entirely: of any size. The smallest residential burner and the largest commercial unit are equally outside; there is no rating at which the exclusion thins.
Practise the exclusion as a dispatch reflex. An oil-fired warm-air system is, in its air side, squarely the kind of system this license covers — and its burner is squarely outside it. Both halves of that sentence are true at once, and holding them together is the competence: the job gets planned so the burner portion is performed by a licensee whose scope includes it. A candidate who resolves the tension by shrinking the exclusion — surely a small burner, surely just a service call — has invented a license Connecticut did not publish.
The rest of the outside
Beyond the oil line, the outside of this license has three further regions, and a complete boundary map names all of them.
The first region is the wider trade itself. Heating, piping and cooling work, as the statutes define the wider term, reaches work this limited license does not claim: boiler and steam-generation apparatus in its breadth, process piping reaching to the machines of a manufacturing process, the full defined span of the unlimited licenses. The unlimited formulation — all heating, piping and cooling work as the statute defines it — belongs to the unlimited tiers of this family. The D-2’s grant is its own sentence, and tasks are sorted by that sentence, not by trade adjacency.
The second region is the family’s shared exclusions. The defined work of this trade family does not include solar thermal work performed under the separate statutory certificate for that work, medical gas and vacuum systems work, or the passive monitoring of heating, air conditioning or refrigeration systems. Those tasks are outside the family’s grants generally, and nothing in the D-2’s scope restores them.
The third region is sideways: electrical work and plumbing and piping work are separately defined occupations under the same chapter, with their own boards and their own licenses. A D-2 holder’s installation that touches those occupations’ work needs those occupations’ licensees for those portions, exactly as their installations need a heating licensee for this trade’s portions. Boundary competence runs in every direction at once.
The employ condition and the rungs around the license
Everything inside the boundary is exercised under one condition: the holder works while in the employ of a licensed contractor. The fact base states no D-2 authority to contract with the public or to perform the work independently, and the condition should be learned as part of the scope rather than as an administrative footnote — it is in the scope sentence itself. The journeyperson performs a full working trade, inside a contractor’s licence.
The ladder gives that condition its context. Below the D-2, the apprentice: a person registered with the Labor Department for the purpose of learning a skilled trade, working under a permit that allows the work only under the supervision of a licensed contractor or journeyman. Above the D-2, named as ladder context only, the D-1 Limited Warm Air, Air Conditioning and Refrigeration Contractor license — this limited line’s own contractor tier. The pattern the sources show is limited-to-limited: the limited journeyperson line runs to its own limited contractor, and no source states that this license feeds an unlimited tier. Plan a career on the rungs as published.
While the ladder is climbed, crews are ratioed. For heating, piping and cooling work, the allowable apprentice-to-licensee ratios run one apprentice to one licensee, two to two, three to three, four to six, five to nine, six to twelve, seven to fifteen, eight to eighteen, nine to twenty-one, and ten to twenty-four; thereafter the ratio continues at three journeypersons to one apprentice. The sequence governs how much licensed oversight a training crew must contain, and a candidate’s formation record is built inside it.
Two timing rules govern the apprentice rung’s exit. A person completing the required apprentice training programme for a journeyman’s license shall, within thirty days following completion, apply for a licensure examination given by the Department. And the apprentice’s permit expires upon the holder’s failure to apply for the first licensure examination following completion of the programme. Completion, application, examination: Connecticut arranges them as one movement.
Qualifying for the examination
The Department states this license’s examination qualification as completion of a registered apprenticeship program or equivalent experience and training. The statute supplies the limited-journeyman frame that sentence operates in: a limited journeyman’s license covers a specific area or areas within the trade, and the required experience for it may be less than four years. That frame is this license’s own. The unlimited journeyman’s statutory terms belong to the unlimited license, and candidates for the D-2 should not measure their route by a sibling license’s frame in either direction — neither assuming the heavier frame applies to them, nor assuming their lighter frame lightens any other license.
For the equivalent experience and training route, the Department’s journeyperson application-path chart lists the D-2 at 4,000 hours of on-the-job training. State the figure the way this guide states it: as the chart’s figure for this license, the documented on-the-job measure an equivalent-route candidate builds a file against. Build that file the way an evaluator reads it — chronologically, employer by employer, with the work placed inside this license’s scope. Hours spent on work outside the boundary do not describe formation for this credential, and a file that sorts its own periods honestly is stronger than a larger file that does not.
Behind the trade route stands the general floor for any Chapter 393 license: the eighteenth birthday attained; evidence of competency as the appropriate board or the Commissioner of Consumer Protection shall require; a diploma or other evidence of graduation from the eighth grade of grammar school, or equivalent education; and the requisite skill to perform the work in the trade applied for. These are statutory conditions of the application, not formalities after it.
Applying, and the out-of-state route
Every individual applicant must take an examination, and separate fees will be due to the exam vendor at time of exam registration. Only individuals can apply; company applications are not accepted, because the license is a person’s credential. The Department does not pre-approve or review applications before submission, so completeness and qualification are the applicant’s responsibility at filing. Examination services for the Department’s occupational trades are provided by PSI, its contracted testing vendor, reached through the Department’s licensing and testing channels.
For candidates licensed elsewhere, the route is equivalency, and the Department’s statement is flat: Connecticut does not have reciprocal agreements with any other jurisdiction. The out-of-state license is evaluated against the Connecticut license type — it must have required the same classroom hours, an equivalent classroom curriculum, and the same on-the-job training hours as the Connecticut type — and the applicant submits one out-of-state license only for that evaluation, with application fees non-refundable. No candidate should plan around reciprocity, and no state should be named as a reciprocal state; the documented route is the evaluation, license by license.
The felony posture belongs in early planning. The Commissioner may deny a license, or issue one under a consent order with conditions, where the applicant reports having been found guilty or convicted of an act constituting a felony of the kind the statute describes. Any individual convicted of a criminal offence may request at any time that the Department determine whether the conviction disqualifies them, and the Department must respond not later than thirty days after receiving a complete request.
When a sitting does not result in a licence, the statute directs that the commissioner provide each failed applicant with information on how to retake the examination and a report describing the applicant’s strengths and weaknesses. Build the next preparation cycle on that report; it is the system’s own account of where the boundary knowledge failed.
Department fees and the annual clock
At the Department layer, this license’s instruments are stated separately, as they are charged. The application fee is $90, non-refundable, for a journeyperson license. The initial license fee is $120, the figure the statute sets for any license other than a contractor’s license. The renewal fee is $120 for a journeyperson. No combined figure is presented anywhere in this guide, because each instrument is paid at its own step — and the vendor layer is separate again, due at exam registration to the vendor and not stated here.
The license runs on an annual clock with a fixed date: all Chapter 393 licenses expire annually, and all heating, cooling and sheet metal work licenses expire annually on August 31st. Renewal notices are sent approximately thirty to forty-five days before expiration, to the email address on file or by regular mail where none is held. After expiration, no licensed work may be performed until a renewal application has been filed. Diarise by the family’s date, not by an issuance anniversary, and treat the notice window as the working window.
Continuing education, for this license, is a verified absence. The continuing-education statute and regulation in this field impose requirements on electricians and plumbers; the Department’s continuing-education index lists no heating, piping and cooling category; and no D-2 hours or cycle appear in the primary sources. Do not schedule another trade’s hours against this license, and check the Department’s own index at renewal time for the current position.
The held license is personal and statewide. Its holder may perform the licensed work in any town or municipality without further examination or licensing. The licensee shall carry the license on their person while engaging in the work and show it to any properly interested person on request. The license is not transferable and may not be used by any other person. And no person shall engage in, practise or offer to perform this work — including offering it in advertising or listings — unless licensed or holding an apprentice registration card under the chapter’s rules.
The field code layer
Work under this license is performed to the Connecticut State Building Code. For permit applications filed from October 1, 2022, that is the 2022 Connecticut State Building Code, based on the 2021 International Codes with Connecticut amendments. Its adopted list carries the 2021 International Mechanical Code with Connecticut amendments as the mechanical volume, the companion plumbing, residential, energy conservation, building and existing building volumes it names, the accessibility standard it adopts, and the 2020 National Electrical Code. The adopted-model-code list contains no International Fuel Gas Code — fuel-gas provisions are carried in the adopted mechanical and plumbing framework and referenced standards. Hold this layer in its proper role: it is the field and permit standard the work is inspected against, with Connecticut’s own amendments, and fluency in the adopted-with-amendments text is the field competence the license presumes. This guide presents the code in exactly that role.
One federal boundary completes the landscape. Federal refrigerant-handling certification under Section 608 of the federal clean-air framework is a separate federal credential, administered on its own terms. No primary source for this license makes that federal certification a condition of the D-2, and this guide does not present it as one. Candidates whose work involves refrigerant handling will meet the federal requirement in the field, under federal law — a separate lane from the state license this guide covers.
A study method fitted to this credential
Sort tasks at the boundary, out loud. Take described work — a gas-fired warm-air changeout with its piping and appliance, an oil burner service call, ductwork for a covered system, a boiler-room task from the wider trade, a medical gas rough-in — and place each inside the boundary, inside an express exclusion, or inside another occupation, naming the clause of the scope that decides it. Boundary fluency is this license’s core skill, and it is trainable as sorting speed with reasons attached.
Learn the two fuel rules as a pair, then separate them. Gas in, oil out — for this license. Then state the neighbouring limited cooling license’s posture and feel the difference: gas out there. The pair drill protects against the family’s easiest confusion precisely because it rehearses both postures in one sitting and assigns each to its own license.
Quote inclusions with their qualifiers. Media piping that is necessary, pumping equipment that is associated, sheet metal work as it pertains to the limitations. Practise the scope sentence with every qualifier in place; a scope quoted loosely will be applied loosely.
Rehearse the route as a file. Write your qualification — apprenticeship completion, or the equivalent route against the Department chart’s on-the-job measure for this license — document by document, before deepening trade study. The Department does not pre-approve applications; the file is judged as filed.
Close with the held license. The August 31 family clock, the Department’s separate fee instruments, the employ condition, and the field code with its Connecticut amendments: the final study pass should be the working year of a D-2 holder, not only the candidate’s month.
Errors this credential’s system is built to catch
Shrinking the oil-burner exclusion by size, by setting, or by calling the work mere servicing. Exporting this license’s gas inclusion to the neighbouring limited cooling license, whose posture runs the other way. Quoting the sheet metal inclusion without its qualifier. Reading limited as a smaller version of unlimited rather than as a different, self-contained scope. Measuring this license’s qualification by the unlimited journeyman’s frame. Calling the out-of-state route reciprocity when the Department states there are no reciprocal agreements. Renewing by an issuance anniversary instead of August 31. Importing another trade’s continuing-education hours into a license for which none are published. Each error adds to Connecticut’s published terms something Connecticut did not publish for this license — and a limited license, being nothing but its published terms, catches the addition every time.
Frequently asked questions
What is the D-2, in one sentence?
Connecticut’s limited journeyperson license for warm air, air conditioning and refrigeration systems, including their media-conveyance piping and associated pumping equipment, issued by the Department of Consumer Protection under Chapter 393 and exercised while in the employ of a licensed contractor.
Is gas work inside this license?
Yes. LP gas supplied by gas containers and natural gas piping are included, and approved gas appliances, gas utilization equipment and accessories are included with them. The neighbouring limited cooling license draws this line the opposite way; the posture belongs to each license separately.
Is oil-burner work inside this license?
No. The license does not include the installation or servicing of oil burners of any size — installation and servicing alike, with no size exception.
What sheet metal work does the license include?
Sheet metal work as it pertains to the credential’s limitations — the qualifier is part of the scope.
What qualifies a candidate for the examination?
Completion of a registered apprenticeship program or equivalent experience and training, within the statute’s limited-journeyman frame. The Department’s journeyperson application-path chart lists this license at 4,000 hours of on-the-job training for the equivalent route.
Which contractor tier sits above the D-2?
The D-1 Limited Warm Air, Air Conditioning and Refrigeration Contractor license — this limited line’s own contractor tier. No source states that the D-2 feeds an unlimited tier, and this guide claims no such feeder.
What does the Department charge?
Stated as separate instruments: an application fee of $90, non-refundable; an initial license fee of $120; and a renewal fee of $120. The exam vendor’s fee is separate, due at exam registration, and is not stated in this guide.
Does Connecticut accept my out-of-state license?
Not by reciprocity — Connecticut states it has no reciprocal agreements with any jurisdiction. One out-of-state license may be submitted for equivalency evaluation against the Connecticut type’s requirements.
When must the license be renewed?
Annually, on the trade family’s fixed date: all heating, cooling and sheet metal work licenses expire annually on August 31st. No licensed work may be done after expiration until a renewal application has been filed.
What continuing education must a D-2 holder complete?
None is published for this license in the primary sources. Continuing-education requirements in this field cover electricians and plumbers; the Department’s index lists no heating, piping and cooling category.
May a D-2 holder do the electrical or plumbing portions of an installation?
The D-2 grants no electrical or plumbing scope. Those are separately defined occupations with their own boards and licenses; their portions of a job belong to their licensees.
What happens after an unsuccessful sitting?
The commissioner provides information on how to retake the examination and a report describing the applicant’s strengths and weaknesses — the starting document for the next preparation cycle.
Is PassProfessor part of the Department or its testing vendor?
No. PassProfessor is an independent preparation provider, not affiliated with the Department of Consumer Protection, the Heating, Piping, Cooling and Sheet Metal Work Examining Board, or PSI. The Department alone licenses and alone determines equivalency. The companion program page is at /connecticut-d-2-limited-warm-air-air-conditioning-and-refrigeration-journeyperson-exam-prep/.
When does enrollment open?
The program is in the works and enrollment is not yet open. Leave an email address on this page and PassProfessor will write to you when the program is ready — and only about this program.
