Arkansas HVACR Contractor Class A/B Exam Guide: Choosing the Class, Reading the Two Outlines, and Sitting the Right Examination

Arkansas licenses HVACR contractors by class through the HVACR Licensing Board. Class A carries no capacity limit; Class B, under Act 746 effective September 1, 2025, reaches 25 tons per unit, 1,000,000 BTUH per unit, and 15 h.p. per unit. Each class sits its own Prov examination — Class A with 100 questions, Class B with 50 — and each table prints the same standard: 70% to pass. The companion program page is at /arkansas-hvacr-contractor-class-a-b-exam-prep/.

This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.

Start with the decision the application forces

Every Arkansas HVACR application begins with a class decision, and the examination follows from it. The applicant must specify the class desired, and Prov — the examination vendor — is not authorised to determine which examination a candidate must take. That allocation of responsibility matters. A candidate who drifts into the wrong sitting has not been misdirected by the test center; the class choice was theirs, made at application, before Board pre-approval. This guide therefore treats class selection as the first examination skill: read the scopes, measure the work you actually intend to perform against the per-unit lines, and only then study an outline.

The two scopes, restated for the decision: Class A performs HVACR work without limitation to BTUH or horsepower capacities. Class B performs HVACR work on air conditioning systems of not more than 25 tons of cooling capacity per unit, or one million (1,000,000) BTUH heating input per unit, and refrigeration systems of fifteen horsepower (15 h.p.) or less per unit. Both classes carry appliance installation and the defined electrical and fuel gas work. HVACR work itself spans design, installation, construction, maintenance, service, repair, alteration, and modification across heating, air conditioning, refrigeration, ventilation, and process cooling or heating. One ton is 12,000 BTUH; horsepower is 746 watts. A contractor whose foreseeable work stays inside all three Class B measures, per unit, has a genuine choice. A contractor whose work crosses any one of them does not: Class A is the license the work requires.

Boundary classes — D, E, and L — exist in the family and are not this guide’s subject. Class C is not a boundary class; it is a repealed one, treated in its own section below because old material keeps presenting it as live.

The legal frame the examinations sit inside

The HVACR Licensing Act is Arkansas Code Title 17, Chapter 33; the rules are Title 17, Part 261 of the Code of Arkansas Rules. The HVACR Licensing Board, inside the Arkansas Department of Labor and Licensing, adopts the mechanical code and work standards, establishes fees and continuing education, and approves candidates for examination. Understanding that frame prevents the most common Arkansas error of the current period: treating an examination bulletin as the law. The bulletin supplies the mechanics of the sittings. Where the bulletin and the current statute and rules describe scope differently, scope follows the statute and rules — a point that is not academic in Arkansas right now, for reasons the Act 746 section explains.

Act 746 and the discipline of current law

Act 746 of 2025 is the hinge of current Arkansas HVACR licensing. Its Class B amendment replaced the earlier cooling ceiling with the current 25-ton per-unit line, effective in the form this guide states throughout: 25 tons, 1,000,000 BTUH, 15 h.p. Its Class C provision struck that class from the statute, with an express transition rule: as of September 1, 2025, all active and current Class C license holders will be Class B license holders, with the work rights of both their former class and Class B. Its working-reach amendments lengthened the gas-fitting connection reach and the electrical-connection reach to seventy-five feet in each case, under the applicable codes. And it restated continuing education as eight hours per International Mechanical Code cycle.

The candidate’s practical problem is that print moves slower than law. Study material, bulletin scope lines, and second-hand summaries prepared before the Act still circulate with the earlier Class B ceiling, a live Class C, the shorter working reaches, and the older education posture. Every one of those positions is repealed law. This guide’s rule is simple and is applied on every page: where a source describes Arkansas scope, class structure, working reach, or renewal education in a form Act 746 replaced, the source is describing history. Preparation keyed to history fails twice — once in the sitting, where law and administration items test current duties, and again in the field, where the license’s actual reach is the current one.

No general effective date for the Act beyond the dated provisions relied on here is asserted in this guide; the Class B line and the Class C transfer are stated with the September 1, 2025 date the sources give them.

Class C, handled once and correctly

Because candidates will encounter Class C in older material, its former shape is worth one precise paragraph — as history. Class C was a service-only license inside the former Class B envelope: its holders could service, repair, and replace components, but could not install original or replace existing HVACR equipment. That description explains old documents and nothing else. There is no Class C application to file, no Class C sitting to book, and no Class C preparation track in the PassProfessor program. The holders who once carried it now carry Class B. Any source that offers Class C as a current Arkansas option is out of date, and the correct response is not to debate it but to set it aside.

The workforce structure: registration instead of a journeyman rung

Arkansas has no journeyman HVACR license, no journeyman examination, and no master license. Below the class licenses stands registration: a registrant holds no Class A, B, D, or E license, performs work only for an HVACR licensee, and holds current registration — with no examination imposed at that tier. Annual registration is the license holder’s responsibility, and licensees must ensure every HVACR employee holds a current registration or license.

For examination planning, the consequence is directness. Qualifying experience is accumulated working for a licensee as a registrant (or through the other routes the rules recognise), and the first Arkansas examination a worker ever takes is the class examination itself. There is no preliminary paper to use as a rehearsal and no intermediate credential to collect on the way. Candidates should plan their readiness accordingly: the Class A or Class B sitting is the gate, whole and entire.

Eligibility, in the order the Board sees it

The statute asks that the applicant be an individual at least 18 years of age, apply on Board-prescribed forms, specify the class desired, meet all Board-rule requirements, pay the appropriate fees, and pass the appropriate examination. The experience rule addresses applicants with no licensing background: satisfactory evidence of at least two years of experience as an HVACR contractor or as an employee of an HVACR contractor. Board-approved HVACR-related educational training may be substituted for experience, with transcripts presented before Board consideration. Proof is taken on the least-restrictive basis — records, affidavits, or bona fide evidence will be considered. Twice over, the rule states that apprenticeship, education, or training shall in no case be a prerequisite or condition for licensure; the substitution route is an option the Board may allow, never a toll the applicant must pay.

Board pre-approval is required before sitting. Criminal background checks are not required, and the Board is not authorised to conduct them, though conviction inquiries and the eligibility and waiver provisions attached to them remain part of the statute. A separate earn-and-learn apprenticeship pathway exists in the rules; it is a route into experience, not an alternative examination. Examinations must be offered at least four times per year or as often as the Board determines.

The Class A examination in full

The Class A examination is delivered by computer through Prov, at testing centers — ten Arkansas locations, plus Prov centers elsewhere in the United States — and remotely at home through Examroom.ai. It presents 100 questions in 240 minutes, open book, with immediate scoring on completion, no penalty for a wrong answer, and the table standard of 70% to pass.

Its outline deserves reading as a portrait of the unlimited license. Systems and Sizing carries 19 questions, the largest single area — appropriate for the class with no ceiling, where sizing judgment is the scope. General Knowledge, Equipment, Maintenance, and Fuel Gas Systems carry 12 each: a broad trade core in which fuel gas stands at full weight, reflecting the gas authorisation both classes hold. Piping carries 10. Plan Reading, Estimating and Math carries 8 — present only in this class, and one of the clearest signals that Class A examines the contractor as an estimator and plan reader, not only as an installer. Refrigeration Systems carries 6, Electrical 5, and Law and Administration 4. The law area is small in count and absolute in effect: it is Arkansas statute and rule, current Act 746 law included, and it cannot be compensated for by strength elsewhere in a candidate’s habits — only prepared for directly.

The Class B examination in full

The Class B examination is its own sitting, not a shortened Class A paper: 50 questions in 180 minutes, open book, immediate scoring, no penalty for a wrong answer, and the same table standard — 70% to pass. It is listed in English and in Spanish (Español); Class A is listed in English.

The Class B outline redistributes weight in a way that tells the candidate what the limited class is examined as. Fuel Gas Systems and Maintenance lead at 8 each. Systems and Sizing carries 7. Piping, Refrigeration Systems, and Electrical carry 5 each. General Knowledge, Equipment, and Law and Administration carry 4 each. There is no Plan Reading, Estimating and Math area at all. A candidate moving between the two outlines should notice the shift in centre of gravity: Class B examines service, maintenance, and fuel gas proportionally harder, and sizing within a bounded envelope, while Class A adds the estimating and plan-reading layer and scales sizing to unlimited work. Study plans that treat Class B as half of Class A misread both papers.

Neither bulletin table publishes a pretest count, and this guide states none for either sitting.

References and the two code layers

Both sittings are open book, and the reference discipline is part of the examination. References must match the printed titles; permanent tabs only, with repositionable tabs and sticky notes barred; highlighting and underlining in pen, done beforehand; no marking during the sitting; no handwritten notes or formulas in any book; no added documents or formula sheets. Results are forwarded automatically to the licensing authority.

The code election is the Arkansas peculiarity candidates must internalise. The examination permits the International Mechanical Code 2018 or 2021 and the International Fuel Gas Code 2018 or 2021 — or the Arkansas Fuel Gas Code, 2018 or 2021, in substitution for the fuel gas code — at the candidate’s election. No single edition is designated as keyed. Sound preparation therefore works the common ground of the two editions confidently and treats edition-divergent provisions as election-dependent: know which edition you will carry, and know the provision in that edition.

The adopted layer is different, and later. The Board has adopted the International Mechanical Code, 2021 edition, as the standard for the conduct of HVACR work. Gas fitting work is performed under the Arkansas Fuel Gas Code; electrical work under the state-adopted electrical code, while the examination’s electrical reference is NEC 2020. A candidate can thus legitimately sit with a 2018 mechanical code and then work to a 2021 field standard. Confusing the examination election with the field adoption — in either direction — is the edition error this state is built to catch.

Class-level references beyond the codes must stay separated. Class A: the Arkansas HVACR law and the rules and regulations material, Manual J-Abridged, 8th edition, Modern Refrigeration and Air Conditioning, 21st edition, and NFPA 70 / NEC 2020. Class B: the same law and rules material, Modern Refrigeration and Air Conditioning, 21st edition, and NEC 2020, with the load-calculation and refrigeration-technology references printed for the Class B list. The two lists overlap; they are not identical, and merging them produces a candidate tabbing a book their sitting does not list while missing one it does.

Fees, renewal, and the license after the sitting

Annual license fees are $200 per year for Class A and $150 per year for Class B, stated alike in the statute’s fee caps and the rule. The Board waives the initial licensing fee, on documented qualification, for applicants in the assistance and income circumstances the rule lists, including income not exceeding 200 percent of the federal poverty guidelines; that waiver does not reach examination fees.

Licenses expire one year after issuance — in the rule’s phrasing, on the last day of the month one year from the original issuance date — and this guide keys no item to a single expiration day without that double phrasing. Renewal requires at least eight hours of continuing education per current International Mechanical Code cycle: Board-approved instruction relating specifically to HVACR construction, installation, maintenance, and repair or the current code, completed before the final year of the code cycle. Without it, the license is not renewed, and the class holder’s license stands suspended until an approved, verifiable certificate is received. Course curricula require Board approval in advance, and providers keep completion records for years afterward — the audit trail is part of the design.

Reinstatement after expiration for nonpayment requires current and past-due fees, late fees, and outstanding civil penalties, with an amended experience record; a monthly late penalty applies, and applicants delinquent over three years take the prescribed examination. After revocation, one year must pass before a licence may be sought again, with the prescribed examination and all fees. Suspension does not restore itself; reinstatement must be requested promptly at the suspension’s end, within the window the rules set.

On retakes, Prov imposes no limit on attempts; a candidate who does not pass waits 2 days before retesting; a passed examination cannot be retaken unless the licensing authority requires it. Reschedule or cancel online at least 3 days ahead without forfeiting the fee; miss the appointment or the deadline and the fee is forfeited. Late arrival after the session begins means turn-away and rescheduling. Registration must use the name exactly as it appears on the government-issued photo identification the candidate will present.

The working licensee: duties candidates will be examined as holding

Law and Administration is only four questions in each outline, but its content is the license’s daily frame, and this guide gives it proportionate space. Liability insurance must be maintained for work performed, directly or through an employer policy, at the rule’s minimum, with proof at issuance or renewal and the stated waivers for in-house and instructor situations. The license number must appear on all business vehicles and all advertising, with vehicle lettering, job-site signage for work in progress, and business-card requirements as the rules specify. Unlicensed work carries no lien rights for the work performed. Civil penalties under current law run per violation per day at the Act 746 level; the earlier, lower cap is repealed and appears in old summaries only.

Reciprocity deserves a full stop. The rules build a framework under which a substantially similar, good-standing out-of-state license could be recognised without examination, with the class license fee still applying. The Board’s own current statement is that it has no reciprocal licensing agreements with any other state licensing board for HVACR licensing at this time. Framework and fact are different things: no state may be named as reciprocal, no holding-period condition from vendor lists may be relied on, and an out-of-state applicant should plan on the examination route the rules provide for non-reciprocity states. Temporary licensure — issued on request on receipt of application, with the examination to be scheduled inside the window the rules set — and military automatic licensure, with its deployment extensions and education exemption window, are real mechanisms with their own terms; neither is a general waiver, and both should be confirmed with the Board by anyone whose situation fits them.

Exemptions bound the whole system: defined household appliances and small factory-assembled equipment, work on one’s own owned-and-occupied home or farm, and listed trades working under a class licensee within their apprenticeship position. A state licensee needs no city or county license, but local permits and inspections still apply. Knowing where the license requirement stops is part of knowing what it is.

A study method fitted to these two sittings

Separate the tracks from day one. Build two outline maps — Class A and Class B — and study only the one you will sit, while keeping the other in view for the scope decision. Cross-contamination between the outlines is the signature Arkansas study error.

Study current law as a distinct subject. Act 746 changed scope, class structure, working reaches, penalties, and renewal education. Give the current statute and rules their own pass, and mark every older summary you own wherever it states a replaced position.

Prepare the books, not just the content. Tab permanently, highlight in pen beforehand, and practise reaching provisions under time. In an open-book sitting with no marking allowed during the examination, retrieval speed is a prepared skill, not a talent.

Work the election deliberately. Decide which code editions you will carry, learn their provisions as your text, and note where the other permitted edition differs so a divergent item does not ambush you.

Weight time by the outline. Class A candidates give Systems and Sizing the largest block and protect the Plan Reading, Estimating and Math area, which has no Class B counterpart to borrow confidence from. Class B candidates give Fuel Gas Systems and Maintenance their leading weight and resist importing Class A estimating material the sitting never asks for.

Finish with the license, not the test. Close preparation with renewal education, insurance, display duties, reinstatement, and the reciprocity position — the four-question law area in each outline, and the frame the successful candidate steps into the morning after passing.

Errors these sittings are built to catch

Blending the classes — scope, outline, references, or fees — is the first. Stating the repealed Class B ceiling, or offering Class C as current, is the second, and it is the error of this examination period above all others. Treating the field code and the examination election as one edition is the third. Assuming a journeyman stage exists is the fourth. Naming a reciprocal state the Board does not recognise is the fifth. Each error is available in plausible-looking material; each is excluded by the statute, the rules, and the Board’s current statements, in that order of authority.

Frequently asked questions

Which class should I apply for?

Measure your intended work, per unit, against the Class B line: 25 tons cooling, 1,000,000 BTUH heating input, 15 h.p. refrigeration. Work that stays inside all three fits Class B; work crossing any one requires Class A, which has no capacity limitation.

Are the two examinations versions of one paper?

No. Class A presents 100 questions in 240 minutes on its own outline; Class B presents 50 questions in 180 minutes on a different outline with no Plan Reading, Estimating and Math area. Each class has its own Prov examination.

What passes?

Each examination table prints the standard in the same form: 70% to pass.

Is there a Spanish sitting?

The bulletin lists Class B in Spanish (Español) as well as English. Class A is listed in English.

Do I take a journeyman examination first?

No. Arkansas has no journeyman license or examination. Workers hold registration and work for a licensee; the class examination is the first and only licensure examination in the route.

What experience must I show?

Applicants with no licensing background present satisfactory evidence of at least two years of experience as an HVACR contractor or an employee of an HVACR contractor. Board-approved training may be substituted as the rule allows, and apprenticeship, education, or training is never itself a prerequisite.

Which code book do I bring?

The examination permits the 2018 or 2021 mechanical and fuel gas code editions at your election, with the Arkansas Fuel Gas Code as a printed substitution. Separately, the adopted field standard is the International Mechanical Code, 2021 edition. Keep the two layers distinct.

How much is the annual license?

Class A: $200 per year. Class B: $150 per year.

What if I fail?

Prov places no limit on attempts; a candidate who does not pass waits 2 days before retesting. A passed examination cannot be retaken unless the licensing authority requires it.

Does my other state’s license count?

The Board states it has no reciprocal agreements at this time. Out-of-state applicants from non-reciprocity states are approved with examination under the rules; do not rely on vendor lists naming reciprocal states.

What keeps the license alive?

Annual renewal, plus at least eight hours of Board-approved continuing education per current International Mechanical Code cycle, completed before the final year of the cycle. Without the education, the license is not renewed and stands suspended until a verifiable certificate is received.

Is PassProfessor the Board or Prov?

Neither. PassProfessor is an independent preparation provider, not affiliated with the HVACR Licensing Board, the Arkansas Department of Labor and Licensing, or Prov. The companion program page is at /arkansas-hvacr-contractor-class-a-b-exam-prep/.

When does enrollment open?

The program is in the works and enrollment is not yet open. Leave an email address on this page and PassProfessor will write to you when the program is ready — and only about this program.