CWI Part B Practice Questions: Welding Inspection and Flaws

Welding Inspection and Flaws is the largest single area of Part B – Practical (minimum 34% under AWS B5.1): the accept/reject judgment an inspector makes on real welds, against stated limits. These ten worked questions present a measurement or a condition and the specification limit that governs it, and ask for the disposition.

THE PROGRAM IN NUMBERS
Fresh
FULL-LENGTH PRACTICE EXAMS
Drawn new for every attempt from the full question bank
Quick
QUICK PRACTICE
Short mini-quiz drills inside the course
20
FREE SAMPLE QUESTIONS
Try the program before you buy
6 months
OF ACCESS
Full access from the day you enroll
Key terms
VOCABULARY MASTERY FLASHCARDS
Mark each term mastered as you learn it

About Part B, stated exactly. The real Part B is a hands-on, open-book examination worked on physical weld replicas with a physical inspection tool kit against the AWS Part B Book of Specifications, at an AWS authorized test center. A question bank cannot reproduce the bench itself. These questions state every specimen reading and acceptance limit in the question text, so you practice the same measurement-and-disposition judgment the examination measures — not the physical specimens.

AWS publishes the passing standard in its own words: “Candidates must achieve a minimum score of 72% on each exam part to obtain the CWI credential.” There is no averaging across parts — each part is passed on its own line.

1. Visual inspection finds a transverse crack 3/8 in. long crossing the face of a completed butt weld. The specification prohibits cracks of any size. What is the correct action?

A. Accept if the crack does not reach the toe

B. Blend it out and accept without further checks

C. Note it as a rounded indication and accept

D. Reject and require removal of the cracked metal and repair

Correct: D. Cracks are prohibited at any size under the stated criterion, so a 3/8 in. transverse crack cannot be accepted or treated as a rounded indication. The cracked metal must be removed and the joint repaired.

2. At the toe of a fillet weld, weld metal rolls over the base metal surface for about 1 in. without fusing to it. The specification states overlap is not permitted. What is the disposition?

A. Reject the affected area for overlap and require repair

B. Accept because the extra metal adds reinforcement

C. Accept if the leg on the other member is full size

D. Accept after painting over the toe

Correct: A. Metal that laps onto the surface without fusion is overlap, which the stated specification prohibits regardless of extra material elsewhere. The unfused lap must be removed and the area repaired.

3. A small fused arc strike is found on the base metal 1/2 in. away from the weld toe. The specification requires arc strikes outside the joint to be removed and the area examined. What should the inspector require?

A. Leave it, since it is outside the weld

B. Remove the strike by grinding and verify the area as specified

C. Cover it with a short weld bead

D. Record it as spatter and accept

Correct: B. An arc strike is a fused spot outside the joint, not loose spatter, and the stated specification requires its removal and examination of the area. Leaving or covering it does not meet that requirement.

4. A 3/8 in. fillet is required. The legs measure 3/8 in., but the face is concave and a fillet gauge shows the throat is undersize, and the specification bases acceptance on maintaining the required throat. What is the disposition?

A. Accept because the legs meet size

B. Reject for insufficient throat and require weld metal to be added

C. Accept because concavity improves toe blend

D. Accept if the concavity is uniform

Correct: B. Leg size alone does not guarantee the required throat when the face is concave. With acceptance based on throat, an undersize throat must be built up to size.

5. A star-shaped crack is visible in a filled crater at the end of a fillet weld. The specification prohibits cracks in welds and craters. What is the correct action?

A. Accept because crater cracks are cosmetic

B. Grind the surface flush and accept without excavation

C. Accept if the crack arms are each under 1/4 in.

D. Reject and require the crack to be excavated to sound metal and rewelded

Correct: D. A crater crack is still a crack and is prohibited by the stated criterion. Surface grinding alone can hide the crack tip, so the crack must be removed to sound metal before rewelding.

6. A 1 in. diameter area of a weld face contains eight pores, each about 1/32 in. The specification treats cluster porosity as rejectable when more than five pores of that size occur in any 1 in. circle. What is the disposition?

A. Accept because each pore is individually tiny

B. Accept by spreading the count over the full weld length

C. Reject the area as cluster porosity exceeding the stated density

D. Accept if the cluster is at a weld restart

Correct: C. Eight pores in the stated circle exceed the limit of five, making the condition cluster porosity beyond the criterion. Individual pore size does not waive the density rule.

7. A groove joint is fit up with a 3/16 in. root opening. The specification for this joint allows a root opening of 1/16 in. to 1/8 in. What should the inspector do?

A. Allow welding because a wider gap is easier to penetrate

B. Hold welding until the fit-up is reset within the allowed opening range

C. Allow welding if the welder slows travel speed

D. Allow welding and note the gap on the final report only

Correct: B. A 3/16 in. opening exceeds the stated 1/8 in. maximum fit-up dimension. Fit-up outside its range is corrected before welding, not compensated for by technique.

8. A required 5/16 in. fillet measures 5/16 in. on both legs, with a slightly convex face, smooth toe blend, and no undercut, porosity, or cracks. The specification requires the stated size and prohibits those flaws. What is the disposition?

A. Accept the weld as meeting size and surface criteria

B. Reject because a fillet face must be perfectly flat

C. Require grinding the face concave

D. Reject until the weld is one size larger

Correct: A. The weld meets the required leg size and shows none of the prohibited surface conditions, with a normal slightly convex profile. Nothing in the stated criteria requires grinding or added size.

9. A single-V groove is specified at a 60 degree included angle, with a tolerance of plus or minus 5 degrees. A protractor reading on the prepared joint shows 52 degrees. What is the disposition of the preparation?

A. Accept because it is within 10 degrees of nominal

B. Accept if the root opening is correct

C. Reject the preparation, because 52 degrees is below the 55 degree minimum

D. Accept after the welder increases amperage

Correct: C. The tolerance gives a range of 55 to 65 degrees, and 52 degrees falls below that minimum. Technique changes do not bring an out-of-tolerance preparation into compliance.

10. A rejected crack has been excavated for repair. Before rewelding, the specification requires the inspector to verify the crack is fully removed. What is the correct next step?

A. Verify the excavation reaches sound metal with no remaining crack indications before authorizing rewelding

B. Authorize rewelding based on the excavation depth alone

C. Skip verification if the welder reports the crack is gone

D. Authorize rewelding and check only the finished surface

Correct: A. Repair welding over a remaining crack tip leaves the flaw in the joint, so removal must be verified in the excavation before rewelding. A finished-surface check afterward cannot prove the crack was fully removed.

Keep going: the full program — 1,500 original questions across all 21 B5.1 content areas, 21 area drills and a full timed Part A simulation — is the AWS Certified Welding Inspector (CWI) Exam Prep course. Read the AWS CWI exam guide for the format, eligibility and passing standard in full, try the free 20-question sample, or enroll for $79 with 6 months of access.

Disclaimer

PassProfessor is an independent exam-preparation provider. This program is exam preparation only: it is not the real exam, it provides no education credit, and completing it does not by itself qualify you for any license or certification. The real exam is run by its own exam body — you register for it, pay its fees, and sit it through that body, not through PassProfessor. All practice questions in this program are original; they are not actual exam questions.