CWI Part A Practice Questions: Metallurgy, Calculations, Duties, Destructive Tests and Cutting

Part A’s five lighter areas under AWS B5.1 still decide sittings: Heat Control & Metallurgy (minimum 6%), Welding Related Calculations (minimum 6%), Duties and Responsibilities (minimum 4%), Destructive Tests (minimum 3%) and Cutting (minimum 2%). These eight worked questions drill them — every calculation is shown in full, so you can check the arithmetic, not just the answer.

THE PROGRAM IN NUMBERS
Fresh
FULL-LENGTH PRACTICE EXAMS
Drawn new for every attempt from the full question bank
Quick
QUICK PRACTICE
Short mini-quiz drills inside the course
20
FREE SAMPLE QUESTIONS
Try the program before you buy
6 months
OF ACCESS
Full access from the day you enroll

AWS publishes the passing standard in its own words: “Candidates must achieve a minimum score of 72% on each exam part to obtain the CWI credential.” There is no averaging across parts — each part is passed on its own line.

1. Two plain carbon steels are compared for welding: one contains about 0.10 percent carbon and the other about 0.45 percent carbon. How does the higher-carbon steel generally behave during welding?

A. It is easier to weld because it cannot harden

B. It is more prone to hardening and cracking in the heat-affected zone and needs more careful heat control

C. It melts at a much lower temperature than the low-carbon steel

D. It requires no filler metal for groove welds

Correct: B. As carbon content rises, steel hardenability increases and the heat-affected zone can form hard, crack-sensitive structures on cooling, so higher-carbon steels demand preheat and controlled practice. Low-carbon steels are comparatively forgiving to weld.

2. Two identical welds are made with the same materials and procedure, but one joint is rigidly clamped in a heavy fixture and the other can move slightly as it cools. Which joint is at greater risk of cracking, and why?

A. The free joint, because movement melts the root

B. The rigidly restrained joint, because shrinkage stresses cannot be relieved by movement

C. Both are at equal risk because restraint has no effect

D. The rigid joint, because clamping removes all hydrogen

Correct: B. Restraint prevents the joint from moving to accommodate weld shrinkage, so contraction strains concentrate as high residual stress that can crack a hard or weak region. Freedom to move slightly is one classic way restraint stress is reduced.

3. A procedure records 28 volts, 180 amperes, and a travel speed of 10 inches per minute. Using heat input equals volts times amperes times 60, divided by travel speed in inches per minute, what is the heat input?

A. 0.50 kJ per inch

B. 302.4 kJ per inch

C. 3.02 kJ per inch

D. 30.24 kJ per inch

Correct: D. Heat input = 28 × 180 × 60 ÷ 10 = 30,240 joules per inch, which is 30.24 kJ per inch. Omitting the factor of 60 leaves only about 0.50 kJ per inch, and the other choices are decimal-place slips.

4. A reduced section measuring 1.4 square inches breaks at a maximum load of 38,500 pounds. Using stress equals load divided by area, what was the ultimate tensile stress?

A. 53,900 psi

B. 27,500 psi

C. 38,500 psi

D. 2,750 psi

Correct: B. Stress = 38,500 ÷ 1.4 = 27,500 psi. Multiplying load by area gives 53,900, and simply restating the load ignores the specimen area entirely.

5. A metric dimension is given as 50.8 millimeters and must be reported in inches. Using 1 inch = 25.4 millimeters, what is the converted dimension?

A. 2.00 inches

B. 1.50 inches

C. 2.54 inches

D. 0.50 inch

Correct: A. 50.8 millimeters ÷ 25.4 millimeters per inch = 2.00 inches. Multiplying the two numbers instead of dividing would give a value over a thousand, which cannot be this dimension in inches.

6. During welding, an inspector finds that the welder is using a current well outside the range in the qualified procedure being followed. What should the inspector do?

A. Quietly adjust the machine and say nothing so production is not disturbed

B. Ignore it if the finished weld surface looks smooth

C. Document the finding and bring it to the responsible supervisor or quality authority for correction

D. Rewrite the procedure on the spot to cover the current being used

Correct: C. The inspector reports and documents departures from the governing procedure so they can be corrected through proper channels. Quietly changing settings, ignoring the departure, or rewriting the procedure exceeds the inspector role.

7. A reduced-section tensile specimen is cut across a welded joint so the weld is in the middle of the gauge length, then pulled to failure. What property does this transverse test primarily establish?

A. The tensile strength of the joint as a whole, compared with the minimum required for the base metal

B. The hardness of the weld face

C. The impact toughness at low temperature

D. The chemical composition of the filler metal

Correct: A. A transverse tensile specimen tests the complete joint in tension, and its breaking strength is compared with the base metal requirement. Toughness and hardness require different specimens and methods.

8. During oxyfuel cutting of carbon steel, the metal is first heated by the preheat flames and then a central jet is opened. What actually removes the metal once that jet acts?

A. The fuel gas melts the steel and it runs out of the cut by gravity

B. A jet of oxygen rapidly oxidizes the heated steel and blows the resulting oxide out of the cut

C. The preheat flame vaporizes the full thickness instantly

D. A rotating tip grinds the steel away mechanically

Correct: B. The cut is a chemical reaction: steel heated to its kindling temperature burns in the pure oxygen jet, and the jet force expels the oxide. Melting alone is not the cutting mechanism for this process.

Keep going: the full program — 1,500 original questions across all 21 B5.1 content areas, 21 area drills and a full timed Part A simulation — is the AWS Certified Welding Inspector (CWI) Exam Prep course. Read the AWS CWI exam guide for the format, eligibility and passing standard in full, try the free 20-question sample, or enroll for $79 with 6 months of access.

Disclaimer

PassProfessor is an independent exam-preparation provider. This program is exam preparation only: it is not the real exam, it provides no education credit, and completing it does not by itself qualify you for any license or certification. The real exam is run by its own exam body — you register for it, pay its fees, and sit it through that body, not through PassProfessor. All practice questions in this program are original; they are not actual exam questions.