Three more of Part A’s core areas under AWS B5.1: Weld Examination (minimum 10%), Welding Performance (minimum 9%) and Test Methods – NDE (minimum 8%). These eight worked questions cover how welds are examined, how welder performance qualification works, and what each nondestructive test method can and cannot find.
AWS publishes the passing standard in its own words: “Candidates must achieve a minimum score of 72% on each exam part to obtain the CWI credential.” There is no averaging across parts — each part is passed on its own line.
1. A macroetched cross-section shows weld metal that filled the groove but never bonded along one sidewall, leaving a clean planar separation. The welder reports the arc had been directed mostly at the opposite wall. This discontinuity is what?
A. Porosity along the sidewall
B. Incomplete fusion at the sidewall
C. A slag line from flux entrapment
D. Normal root penetration variation
Correct: B. Incomplete fusion is a lack of bonding between weld metal and base metal or passes, here at the sidewall where the arc was not directed. It is a planar discontinuity even though the groove looks filled.
2. The inside root of a long, small-diameter pipe run cannot be reached or seen directly by the inspector. Which approach still allows a visual-type examination of that root?
A. Relying on the welder’s verbal report alone
B. Skipping the root examination entirely
C. Using radiography and calling it direct visual examination
D. Using a borescope or similar remote visual device
Correct: D. Remote visual examination with devices such as borescopes or cameras extends the eye to surfaces that cannot be viewed directly. It is the visual method adapted for inaccessible areas.
3. A short crack is found in the base metal running parallel to the weld, just outside the fusion boundary in the region that was heated but not melted during welding. In which weld zone is this crack located?
A. In the center of the weld metal
B. In the unaffected base metal far from the weld
C. In the root reinforcement
D. In the heat-affected zone
Correct: D. The heat-affected zone is the base metal beside the weld that was heated enough to change its properties without melting. Cracks parallel to the weld in that band are heat-affected zone cracks.
4. A welder qualified a year ago has not welded with that process at all since the test, and the applicable rules set a six-month continuity period. What is the status concern the inspector should raise?
A. The qualification may have lapsed because the welder has not used the process within the continuity period
B. The welder automatically becomes qualified for all processes
C. Continuity depends only on attending safety meetings
D. Nothing changes until ten years have passed
Correct: A. Performance qualifications commonly expire when the welder does not use the process for a period longer than the allowed continuity interval. The record must show use within that interval to stay current.
5. Before a performance coupon is cut for bend specimens, the inspector marks the coupon with the welder’s identification and test information. Why is this marking step essential?
A. Markings make the specimens bend more easily
B. It is decorative and can be skipped when busy
C. It preserves traceability so test results can be tied to the correct welder, procedure, and test conditions
D. It replaces the written qualification record
Correct: C. Specimen results are only meaningful when they can be traced to the welder and conditions that produced them. Marking maintains that chain, though the written record is still required.
6. A production joint will be welded with a gas tungsten arc root pass followed by shielded metal arc fill passes, and one welder will do both portions. How must that welder’s performance qualification be considered?
A. The welder must be qualified for each process used, within the thickness each process deposits in the test as the rules assign
B. Qualifying for either process alone covers both automatically
C. Combination joints never require qualification
D. Only the fill process matters because it deposits more metal
Correct: A. Each process in a combination joint requires its own demonstrated skill, and deposited thickness per process can affect qualified limits. A single unrelated process qualification does not cover the other process.
7. Before any other nondestructive method is applied to a completed groove weld, an inspector plans to examine the weld face, toes, and adjacent base metal with the unaided eye and a flashlight. Why is this visual step normally performed first?
A. It measures the depth of internal porosity
B. It replaces the need for any volumetric method
C. It finds surface conditions cheaply and shows where other methods will be most useful
D. It proves the weld has the required tensile strength
Correct: C. Visual testing is the fastest and least costly way to find surface discontinuities and poor profile, and its findings guide where surface or volumetric methods should be concentrated. It cannot size internal flaws or prove mechanical strength.
8. A weld surface was heavily peened after welding, closing the mouths of shallow cracks, and a penetrant examination finds nothing. Why can penetrant testing miss this condition?
A. Penetrant cannot enter discontinuities that are not open to the surface
B. Peening makes the surface too magnetic for penetrant
C. Penetrant only works on nonferrous metals
D. Peened surfaces are always too hot for penetrant
Correct: A. Penetrant must physically enter a discontinuity through an opening at the surface, and mechanical smearing such as peening can seal that opening. Penetrant works on ferrous and nonferrous materials alike when the opening is accessible.
Keep going: the full program — 1,500 original questions across all 21 B5.1 content areas, 21 area drills and a full timed Part A simulation — is the AWS Certified Welding Inspector (CWI) Exam Prep course. Read the AWS CWI exam guide for the format, eligibility and passing standard in full, try the free 20-question sample, or enroll for $79 with 6 months of access.
Disclaimer
PassProfessor is an independent exam-preparation provider. This program is exam preparation only: it is not the real exam, it provides no education credit, and completing it does not by itself qualify you for any license or certification. The real exam is run by its own exam body — you register for it, pay its fees, and sit it through that body, not through PassProfessor. All practice questions in this program are original; they are not actual exam questions.
