South Dakota Plumbing Contractor Exam Guide: The Three Parts, the Drawings Sizing Exercise, and the Six-Year Gate

South Dakota licenses its top plumbing tier as the Plumbing Contractor, examined directly by the South Dakota State Plumbing Commission in three parts with mixed book status: a code part in which the code may be used, a code part in which it may not, and a drawings-based sizing exercise. The published standard is stated in the rule’s own words: “The passing grade for plumbing contractors is 80 percent.” This guide works through the route in full — the experience gate, the application-first sequence, each part’s discipline, the code as adopted with South Dakota amendments, fees, continuing education, and the three-month retake interval. Its companion program page is at /south-dakota-master-plumber-exam-prep/.

This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.

The credential at a glance

ItemVerified position
ProgramSouth Dakota Plumbing Contractor: the top examined tier in South Dakota plumbing licensure. The class below is named simply Plumber
RegulatorSouth Dakota State Plumbing Commission (Department of Labor and Regulation), under SDCL chapter 36-25 and ARSD Article 20:53; the Commission serves as a committee of plumbing examiners
AdministratorCommission-administered, in person: Pierre by appointment; Sioux Falls or Rapid City when 8–10 applicants warrant
Examination structureThree parts: Part 1, code-based questions, code may be used, maximum 2 hours; Part 2, code-based questions, code may not be used, maximum 2 hours; Part 3, drawings sizing exercise, maximum 1 hour, code may be used for the plumbing contractor examination
Passing standardPublished verbatim: “The passing grade for plumbing contractors is 80 percent”
Code basisThe state plumbing code: the 2024 Uniform Plumbing Code as adopted with 59 South Dakota amendments and stated exclusions
Fees statedApplication $50; examination and reexamination $100; Plumbing Contractor license and annual renewal $275
Administrator notePassProfessor is independent and is not affiliated with the South Dakota State Plumbing Commission

South Dakota’s scheme repays attention precisely because it refuses the familiar labels. There is no master class and no journeyman class in state law; the verified negatives are stated once here and govern the whole guide. There is no vendor bulletin to summarise, because the Commission administers its own examinations and no vendor is named in any primary source. There is no published question count and no published content outline for any South Dakota examination — verified negatives again — so this guide builds its account from what the rule itself publishes: the three parts, their book rules and maxima, the sizing work Part 3 requires, the passing sentence, and the licensing rules around them. A guide that invented counts or weights to fill those spaces would be less useful, not more, because it would send candidates pacing a sitting by numbers the Commission never gave them.

Reading the verified facts

Three layers carry this state’s facts, and the guide keeps them distinct. The statute, SDCL chapter 36-25, supplies the definitions — including the contractor definition quoted below — the Commission’s examining role, and the cap on examination fees. The licensing rules at ARSD Article 20:53 supply the examination’s parts, book rules, maxima, passing sentence, experience gate, retake interval, and fees. The code article at ARSD Article 20:54 supplies the adopted code the examination keys on. Where a proposition appears in none of those layers — how the passing grade is computed across parts, what form of the code a candidate may physically carry, who grades under the current rules — this guide says it is unpublished rather than borrowing an answer from another state’s system or from secondary material. South Dakota candidates are best served by knowing exactly where the published ground ends.

The route, step by step

Step one — build the experience record. Six years of experience as a plumbing contractor, plumber, or plumber’s apprentice, with at least two of those years as a plumbing contractor or plumber, at at least 1,900 hours per year. Since November 3, 2026, qualifying training must be licensed work experience, creditable only if completed after the applicant was issued the applicable license, and the Commission may call for a supervisor experience affidavit. Assemble the record in that form from the start: years, capacities, hours per year, and the licences in force while the work was done.

Step two — apply, with fees, and be approved. The sequence is application-first: fees are submitted and the application approved before any sitting is scheduled. The application fee is $50 and the examination fee is $100. Approval starts a clock — exam applications expire six months from approval, and fees are forfeited on failure to appear — so the application should be filed when preparation is substantially complete, not at its beginning.

Step three — sit at a Commission sitting. Sittings are held in Pierre by appointment, and in Sioux Falls or Rapid City when eight to ten applicants warrant a session. Candidates outside Pierre should note the warrant condition: a regional session exists when enough applicants gather, which makes early application, coordinated with the Commission’s scheduling, a practical part of the route rather than an afterthought.

Step four — complete all three parts inside their maxima: two hours with the code, two hours without it, and one hour on the drawings sizing exercise with the code available, as detailed in the part-by-part sections below.

Step five — meet the published standard, printed verbatim in its own section below, and receive the Plumbing Contractor license at the $275 license fee, renewed annually at the same figure, with the four hours of continuing education described below earned in each license period. If the sitting is failed, the retake interval governs the next step: one sitting for the same license only once every three months, with the reexamination fee submitted at least two weeks before a Sioux Falls or Rapid City session.

What the contractor tier authorises, and where the Plumber class sits

The statutory definition at §36-25-1(6) describes the plumbing contractor as a person qualified and skilled in the planning, superintending, and practical installation of plumbing, qualified and registered to contract for plumbing installations and conduct the business of plumbing. Each verb in that definition maps to the examination. Planning and superintending are the business-facing capacities the contractor tier adds; contracting is the legal act the license permits; and the practical-installation grounding is what the code parts and the sizing exercise verify in examination form.

The Plumber class, by contrast, works as an employee of, or under the direction of, a plumbing contractor. Its own gate — four years as an apprentice plumber at at least 1,900 hours per year, with defined credit routes in the rules including military plumbing credit — is stated here only to fix the ladder’s shape: apprentice experience feeds the Plumber class, Plumber and contractor-level years feed the contractor gate, and at least two of the contractor applicant’s six years must sit at the contractor or plumber level. The two examinations may differ — the rule states that the questions and drawings for plumbing contractors and plumbers may be different — and this guide treats the contractor sitting throughout as its own examination, including the one book-rule contrast that matters most: on Part 3, the code may be used for the plumbing contractor examination, while it may not be used on Part 3 of the Plumber examination. Candidates stepping up should not carry the lower sitting’s Part 3 discipline into the contractor room.

Part 1 in depth: code questions with the code

Part 1 allows two hours at most, and the code may be used. That permission defines the skill examined: not recollection, but retrieval and application. The candidate is given code-based questions and a code book — the state plumbing code as adopted — and is measured on finding the governing provision, reading it accurately in its amended South Dakota form, and applying it to the situation the question poses.

Preparation for this part is therefore procedural as much as substantive. The candidate needs a mental map of the adopted code’s organisation that survives South Dakota’s amendments and exclusions — including the knowledge that whole chapters and appendices of the model code are excluded from the adopted text, so a provision confidently recalled from an unamended edition may simply not be South Dakota law. Timed lookup drills, worked against the amended text, are the honest rehearsal: each drill measures not whether the answer was eventually found, but whether it was found inside the allowance the part’s pace requires. The error this part catches is the slow, correct candidate — right in principle, out of time in practice.

Part 2 in depth: code questions without the code

Part 2 also allows two hours at most, and the code may not be used. Same family of questions, opposite discipline: the provisions must be held, not found. This is the part candidates most often misjudge when they describe the examination to themselves by a single book label, because the half of the code examination sat without the book disappears inside that shorthand.

What must be held is the working core a contractor uses daily without reaching for a shelf: the sizing principles, the venting and drainage rules that govern ordinary layouts, the clearances, materials, and protection rules that recur across jobs, and the South Dakota amendments that change the model-code answer a candidate may have learned elsewhere. Part 2 is where an out-of-state formation shows most plainly, because a provision remembered correctly for another code may be remembered wrongly for this one — amended, excluded, or superseded in the adopted text. Recall drilling must therefore run on the amended code from the first session: flashcards and timed written recall built from the South Dakota text, not from a generic national summary, with every recalled provision checked back against the adopted wording. The PassProfessor program sequences Part 2 preparation as its own block for exactly this reason, interleaved with Part 1 lookup work so the candidate practises the switch between finding and knowing that the sitting itself demands.

Part 3 in depth: the drawings sizing exercise, disclosed in full

Part 3 allows one hour at most. The rule describes its task precisely: the applicant is given drawings of plumbing fixtures on which the applicant is to size all stacks, wastes, and vents and to insert the pipe size. For the plumbing contractor examination, the code may be used during this part.

Two clarifications frame honest preparation. First, Part 3 is a drawings-based sizing exercise — production work on paper, in which the candidate’s output is a sized system recorded on the drawings provided. It is not a hands-on practical: no primary source describes pipe-joining, installation, or any other hands-on component in any South Dakota examination, and neither this guide nor the program page describes Part 3 in practical-examination language. Second, Part 3 is not rehearsed by multiple-choice drilling alone, however thorough. Sizing a drawn system requires the candidate to accumulate fixture demand through a layout, follow stacks, wastes, and vents through the drawing, and commit to pipe sizes — a chain of judgements in which an early misreading propagates. The one-hour maximum makes it a paced performance as well as a technical one.

Preparation that matches the part therefore works from drawings throughout: drawn fixture arrangements of increasing complexity, sized end to end under a shrinking clock, with the adopted code open as the sitting allows, and with each completed exercise audited for the three classic failures — a branch undersized from a mis-added load, a vent omitted or undersized where the drawing conceals it, and sizes recorded incompletely where the hour ran short. The PassProfessor drawings-sizing block is built on that pattern, because a candidate who has only ever selected sizes from options meets a materially different task in Part 3 from the candidate who has repeatedly produced them.

The passing standard and its published limits

The rule at §20:53:03:07 publishes the standard in a single sentence, printed here verbatim as this guide prints it everywhere: “The passing grade for plumbing contractors is 80 percent.” The same sentence gives the Plumber class a passing grade of 70 percent, stated in this guide only as ladder context.

Candidates should understand precisely what the published sentence does not say. It does not state whether the 80 percent is computed across the whole examination or required in each part. It does not state a raw number of correct answers, and none can be derived, because no question count is published for any part or for the whole. It does not state that a passed part may be banked while a failed part is retaken, and no part-banking rule appears in any primary source behind this guide. The disciplined response to each silence is the same: prepare as though every part must stand on its own — including the sizing exercise, whose production format makes a compensating-surplus strategy incoherent in any case — and treat that discipline as prudence, not as a published rule. Any source that resolves these silences with a confident figure or a banking promise is resolving them without the Commission.

The code basis in depth: one adopted code, amended

The examination rule bases the examination on “the state plumbing code” without naming an edition in the examination layer. The code article supplies the edition: ARSD §20:54:02:01 adopts the 2024 Uniform Plumbing Code, published by IAPMO on January 1, 2024, with 59 South Dakota amendments and exclusions that include Uniform Plumbing Code Chapter 5, Chapters 12 through 14, Appendices F, G, H, J, P, and S, and listed sections. SDCL §36-25-15 independently requires plumbing to be in substantial accord with the 2024 Uniform Plumbing Code. Adopted and tested thus join by construction: the examination’s “state plumbing code” is the 2024 code as South Dakota adopted it.

The exclusions deserve the candidate’s particular attention, because they invert the usual study instinct. Material inside an excluded chapter is not South Dakota examination material merely because it appears in a national edition of the code; material inside an amended section is examination material in its amended form, not its model form. A preparation library organised by the model code’s table of contents, without an amendment overlay, will systematically over-teach the excluded ground and under-teach the amended ground. This program’s code material is organised on the adopted text, with the amendments carried inside the provisions they amend, so that Part 1 lookups and Part 2 recall rehearse the same South Dakota wording the sitting applies.

What may physically be brought into the room, beyond the rule’s per-part statements that the code may or may not be used — the form of the book, and any inspection or marking rules — is not stated in any examination-facing primary source behind this guide. This guide states no rule for it. Candidates should confirm the room arrangements with the Commission when scheduling, and should arrive prepared for the book rules the rule itself does publish: available in Parts 1 and 3, unavailable in Part 2.

Fees, renewal, continuing education, and the retake clock

The fee set corroborated for this program is stated here in full and kept in its layers. Application: $50. Examination and reexamination: $100, payable before the examination, non-refundable, and capped at $100 by SDCL §36-25-19; one examination only is covered by each fee paid. License and annual renewal for the Plumbing Contractor: $275. No state bond or insurance minimum exists for this license — a verified position in the sources behind this guide — so a bond figure offered as a state requirement belongs to another layer, most plausibly a local one, and should be verified where it is claimed rather than budgeted as a state charge.

Renewal carries the continuing education duty: four hours in the previous license period, at least two of them code-related, an hour being no fewer than 50 minutes. The duty binds the plumbing contractor at renewal, and reciprocity applicants owe the same four hours before issuance. Four hours is a small number with a hard edge: it must be earned inside the previous license period, and a contractor who treats it as an afterthought discovers the shortfall at renewal, when the period has closed.

The retake rule is a single sentence with large planning consequences: an applicant may sit for the examination for the same license only once every three months. No attempt cap beyond that interval is published. A failed sitting therefore costs a season, not a week — and it costs it inside the six-month life of the approved application, after which fees are forfeited on failure to appear and the application sequence must be considered afresh. For Sioux Falls and Rapid City sessions, the re-examination fee must be submitted at least two weeks prior to the session. The rational response is to sit first when ready: fully prepared, on a date chosen inside the application’s life, with the regional-session warrant in mind.

Reciprocity, finally, is a mechanism and not a list. The sources describe registration without examination where the other state’s regulation is substantially equivalent, the applicant was licensed by examination, that state’s laws are similar, and its code is equal or better — with the examination fee payable despite no examination being sat, and the four continuing education hours owed before issuance. No state is named as qualifying in those sources, and this guide names none.

A study plan built on how this examination is actually put together

First, anchor everything to the adopted code. Build the amendment overlay before building speed: know which chapters and appendices are excluded, which sections are amended, and where the South Dakota answer departs from the model answer. Every later drill inherits this map.

Second, run Parts 1 and 2 as paired opposites. Alternate timed lookup sessions, code open, against timed recall sessions, code closed, on the same subject matter in the same week. The sitting alternates the disciplines; preparation that blocks them into separate months never practises the alternation, and Part 2 recall built only after Part 1 fluency arrives too late to harden.

Third, give the sizing exercise its own weekly session from the beginning. Drawn systems, sized in full, inside an hour that shrinks as accuracy firms. Audit every exercise for undersized branches, missed vents, and incomplete recording, and repeat the failing drawing type until it holds.

Fourth, respect the clocks outside the room. Apply when preparation is substantially complete, because approval starts a six-month application life; sit at the first sitting the preparation honestly supports, because a failure costs three months; and keep the four continuing education hours current from the first license period onward.

Fifth, close with full rehearsals in sitting order — two hours open, two hours closed, one hour on drawings — scored by discipline rather than by an invented total, with every error sorted as lookup error, recall error, amendment error, or sizing error. Each family carries its own cure, and the final fortnight belongs to whichever family still produces errors.

The errors this examination is built to catch

Describing it by a single book label hides the closed-code half of the examination and under-prepares it. Importing a question count or an outline from secondary material paces preparation by figures the Commission has never published. Assuming the standard compensates across parts wagers the licence on an unpublished computation; the published sentence supports no such wager. Studying the unamended model code teaches excluded chapters as if they governed and amended sections as if they did not. Treating Part 3 as a topic rather than a task — reading about sizing instead of producing sizes on drawings — fails the one part whose output is production. And applying before preparing, inside a six-month application life with a three-month retake interval, converts an administrative sequence into a deadline the candidate set against themselves.

South Dakota in one view

South Dakota in one view is a commission that examines its own contractors, in its own rooms, on its own code. The Plumbing Contractor — the top of a ladder whose middle rung is named simply Plumber — is gated by six years of licensed trade experience, examined in three parts that divide code knowledge into what must be findable, what must be known, and what must be produced on drawings, and held to a single published sentence of a standard: “The passing grade for plumbing contractors is 80 percent.” Around that spare structure sit a short corroborated fee set, a four-hour continuing education duty, and a three-month retake interval that rewards readiness over reconnaissance. The candidate who learns the adopted code in its amended form, trains both book disciplines, and practises sizing on drawings until the hour feels roomy holds the whole examination at once. The companion program page, with enrollment notification, is at /south-dakota-master-plumber-exam-prep/.

Frequently asked questions

Does South Dakota publish a content outline for the contractor examination?

No. No content outline, blueprint, or topic weighting is published for any South Dakota examination, and no question count is published either. This guide states none and builds on the rule’s description of the three parts.

How long does the whole examination take?

The rule sets maxima per part rather than a single total: two hours for Part 1, two hours for Part 2, and one hour for Part 3. The three maxima add to five hours.

May I use the code throughout?

No. The code may be used in Part 1 and, for the plumbing contractor examination, in Part 3. It may not be used in Part 2. On Part 3 of the Plumber examination, by contrast, the code may not be used — a ladder contrast worth noting for candidates stepping up.

If I fail one part, may I retake only that part?

No part-banking or part-retake rule is published in any primary source behind this guide, and this guide claims none. The published retake rule is the interval: one sitting for the same license only once every three months.

What continuing education does renewal require?

Four hours in the previous license period, at least two of them code-related, with an hour counted at no fewer than 50 minutes. Reciprocity applicants owe the same four hours before issuance.

Is a bond required for the state contractor license?

No state bond or insurance minimum exists for this license. A bond figure presented as a state requirement belongs to another layer and should be verified where it is claimed.

Can I transfer a contractor license from another state?

South Dakota provides a reciprocity mechanism — registration without examination where the other state’s regulation is substantially equivalent, licensure was by examination, its laws are similar, and its code is equal or better — with the examination fee payable and four continuing education hours owed before issuance. No qualifying state is named in the sources behind this guide, and none is named here.

Where are sittings held?

In Pierre by appointment, and in Sioux Falls or Rapid City when eight to ten applicants warrant a session. The examinations are Commission-administered; no vendor conducts them.

What experience counts toward the six years?

Experience as a plumbing contractor, plumber, or plumber’s apprentice, at at least 1,900 hours per year, with at least two of the six years as a plumbing contractor or plumber. Qualifying training must be licensed work experience completed after the applicable license was issued.

When does enrollment open for the PassProfessor program?

The program is in the works and enrollment is not yet open. Leave an email address on this page and PassProfessor will write to you when the program is ready — and only about this program.