New Hampshire licenses its Master Plumber through the Mechanical Licensing Board, with the examination delivered by Prov: 100 questions in 180 minutes, open book, passed at 75 percent — on the International Plumbing Code 2018, even though the state has adopted the International Plumbing Code 2024 with effect from July 1, 2026. The PassProfessor New Hampshire Master Plumber program prepares candidates for that sitting, and this guide sets out the credential, the route, and the sitting in full.
This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.
The credential at a glance
| Item | Verified position |
|---|---|
| Program | New Hampshire Master Plumber |
| Authority | Mechanical Licensing Board, within the Office of Professional Licensure and Certification (OPLC), under RSA 153 |
| Vendor | Prov — single-part computer-based test; Board pre-approval required before scheduling; scoring is immediate |
| Code tested | International Plumbing Code 2018 — 100 questions / 180 minutes / 75 percent to pass / OPEN BOOK / fee $90 |
| Code adopted | International Plumbing Code 2024, effective July 1, 2026, with the 2021 edition in concurrence through December 31, 2026 — candidates are examined on 2018 |
| Content outline | 100 questions across eight published areas; Scope and Administration, Calculations, Venting Requirements, and Drainage Requirements carry 15 each |
| Practical / drawing production | None — plans and sizing are tested by multiple choice only |
| Retake | No required waiting period |
| Fees (licensing and examination fees) | Examination $90, paid to Prov; licensing fee $330 (combined fee, 2-year license) |
| Term and education | Term 2 years from issuance; continuing education 6 hours per endorsement per cycle |
| Administrator note | PassProfessor is independent and is not affiliated with the Board or OPLC |
A candidate reading this guide cold should take away one structural picture before any detail: New Hampshire examines its master plumbers on a code edition the state no longer adopts, through a vendor the Board contracts with, under an approval gate the Board controls, at a standard five points above the journeyman standard in the same bulletin. The edition gap decides what to study; the approval gate decides when a sitting can be scheduled; the outline decides where the master weight sits; the 75 percent standard decides how much margin preparation must build. The companion New Hampshire Master Plumber Exam Preparation page gives the program in one view.
The credential family, and where the master sits in it
Plumbing in New Hampshire is licensed by the Mechanical Licensing Board, a unit within the Office of Professional Licensure and Certification, under RSA 153, sections 153:27 through 153:38 — mechanical licensing, with plumbing and fuel gas under one board. There is no standalone board of plumbers in current law. The Board has five members, appointed by the Governor with the Council: two licensed journeymen or master plumbers, one licensed fuel gas fitter, one certified heating equipment installer or service person, and one public member. Its rules run in the Mec chapters.
The plumbing family under the Board has four credentials. The apprentice plumber is a license without an examination, enrollment-based. The journeyman plumber is an examined license. The master plumber is an examined individual license, and the holder is deemed qualified as a journeyman. The mechanical business entity license is the firm credential, available to corporations, partnerships, limited liability companies, sole proprietors, and limited liability partnerships; it carries no examination and no continuing education, and the entity’s licensee of record for plumbing scope must be a master plumber. No business may perform plumbing work without a business entity license. There is no separate plumbing contractor license anywhere in this family. The same Board also licenses the fuel-gas family and runs voluntary oil-heating certifications, none of them examined; none of those is this program.
The statutory definition explains the family’s shape. A master plumber, in the statute’s terms, is a person, firm, corporation, or limited liability company that, as a business, hires or employs other persons to do plumbing work, or — without employing any person — does that work as a principal business, or ancillary to one, for its own account. In practice the individual license and the business function are held through the two distinct credentials above: the person holds the master license, and the firm holds the entity license with the master as its plumbing licensee of record. The examination therefore certifies the individual through whom a New Hampshire plumbing business is licensed to operate.
The route, step by step
Step one — complete the journeyman standing the gate requires. The master gate is not a count of years in the trade generally. It requires that the applicant have held a New Hampshire journeyman license for at least six months, show good character and professional competence — including being a journeyman without consumer complaints resulting in board disciplinary sanctions within the past year — and be eighteen years of age or older. The journeyman license behind that standing is itself earned through apprenticeship completion, not less than 600 hours of educational training, and not less than 8,000 working hours of experience, plus the journeyman examination. The clean-year condition is part of eligibility, not a formality after it.
Step two — assemble the packet and obtain Board approval. The supporting materials include one signed letter from a supervising licensed plumber and the examination score, and the Board approves or denies within sixty days of a completed packet. Board pre-approval is required before scheduling: the Board provides Prov the registration information, and Prov is not authorised to determine which examination a candidate must take. Candidates who prepare first convert the approval interval into final rehearsal.
Step three — register with Prov and pay the examination fee. The examination fee is $90, paid to Prov at registration. The same $90 figure appears in the Office’s fee rule for each of the Bypass, journeyman, and master examinations, so the two layers agree.
Step four — sit the examination. The sitting is a single-part, computer-based, multiple-choice examination of 100 questions in 180 minutes, open book, offered in English, at Prov centres or remotely. The mechanics are detailed below.
Step five — meet the standard and license. The master standard is 75 percent. On passing, the licensing layer is the $330 combined fee, for a two-year license. Holding terms are detailed in the holding section.
Three editions, three jobs: tested, adopted, and concurrent
New Hampshire’s edition position needs a full section because candidates routinely collapse it into one wrong sentence. The layers, stated separately: Tested: the International Plumbing Code 2018, listed in Prov’s current candidate bulletin — effective October 31, 2026 — as an open-book reference for both journeyman and master examinations, together with the Board’s administrative-rules document. Adopted: the International Plumbing Code 2024, with New Hampshire amendments approved through October 10, 2025, ratified in 2026 and effective July 1, 2026. The prior adopted edition was the 2021 edition, effective July 1, 2025; before that, the 2018 edition was adopted from July 1, 2022. Concurrent: from July 1 through December 31, 2026, permit applicants may elect the 2021 or the 2024 edition, but not a combination; from January 1, 2027, the 2024 codes govern all permit requests.
The bulletin dated October 31, 2026 — issued four months after the 2024 adoption took effect — still keys the examination to the 2018 edition. Adoption moves on the legislature’s timetable, while the examined edition moves on the Board’s and its vendor’s timetable, and no announcement of an examination transition to the 2021 or 2024 edition appears in the verified record. A candidate who studies the 2024 book because it is in force, or the 2021 book because it is electable on permits through 2026, will be examined on the 2018 text. Permit concurrence confers no choice in the examination room.
One bulletin rule deserves direct handling because it is easily misread. Prov’s general reference rules provide that, for an exactly titled book, older or newer editions are permitted in the room. That is a room-admission rule about the candidate’s own physical copy. It is not a statement that the examination is edition-neutral, and it does not change the keyed edition, which remains the 2018 code. Bring the book the examination is keyed to, and let the adopted editions wait for the job site.
The sitting itself: centres, remote delivery, and the reference rules
Prov delivers the examination at testing centres and remotely. The New Hampshire centres in the current bulletin are in Concord, at two sites, Nashua, and Newington; candidates may also sit at any Prov centre nationwide, or test remotely. Lists of New Hampshire testing cities in secondary material beyond those named here are not the bulletin’s list.
Scoring is immediate on completion and forwarded to the licensing authority. There is no marking interval to wait through — and nothing after the sitting to repair a weak performance except a retake.
The reference rules govern what the open book actually means in this room, and they are narrower than many candidates assume. Only references marked as open book are permitted: for this sitting, the 2018 plumbing code and the Board’s administrative-rules document. Permanent tabs are permitted; moveable tabs and sticky notes are not. Highlighting and underlining are permitted in pen only. No marking may be made in any book during the examination. No handwritten notes or formulas may appear in any reference, and no added documents or stickers are allowed. Photocopied references are permitted only where the examination details state it, and no such statement is made for either plumbing examination. These rules reward a book prepared in advance — permanently tabbed, pen-highlighted, thoroughly familiar. There is no penalty for wrong answers, so the final minutes belong to unanswered questions.
Pacing follows from the arithmetic. One hundred questions in 180 minutes averages a minute and three-quarters per question, but the outline does not spend time evenly: the fifteen Calculation questions and the heavier system areas will legitimately consume more than the average, paid for by Fundamentals and Fixtures questions answered from knowledge in well under it. The study plan below trains exactly that economy.
The published outline in full, and the rule list that must not be merged with it
The bulletin’s master outline sums to 100 questions, and each area is stated here with its count, because the counts are the preparation map.
Scope and Administration — 15 questions. The master paper’s signature area, absent from the journeyman outline entirely. It examines the code’s scope and administrative framework and the regulatory structure the master works inside — the knowledge a licensee of record uses when the question is whether work may proceed at all.
Calculations — 15 questions. Sizing and fixture calculations at master depth, examined by multiple choice. The area rewards candidates who can set up the computation correctly under time, not merely recognise a correct result.
Venting Requirements — 15 questions. Venting at full system depth, here examined at the master standard.
Drainage Requirements — 15 questions. Drainage systems, sizing, and requirements, at the same weight as venting; together the two areas are thirty of the hundred questions.
Plumbing Fundamentals — 10 questions. The foundational principles beneath the system areas.
Traps and Interceptors — 10 questions. Trap and interceptor requirements and application.
Water Distribution — 10 questions. Water supply and distribution requirements and sizing.
Fixtures and Faucets — 10 questions. Fixture requirements, counts, and fittings.
Beside this counted outline stands a second list that must be kept distinct from it. The Board’s rules describe the master examination as multiple-choice questions across fourteen topics: drainage; basic and advanced plumbing theory; reading and interpretation of plumbing plans and drawings; venting; potable water systems; material selection; backflow prevention; commercial kitchen plumbing; system sizing and fixture calculations; accessibility requirements; testing, inspection, and disinfecting; plumbing codes and standards including amendments as adopted in the state; code administration; and New Hampshire statutory and regulatory law. No per-topic counts are published for that list, and the bulletin’s counted areas contain no separate lines for several of its topics — New Hampshire law, commercial kitchen work, accessibility, and backflow among them. Prepare by the bulletin’s counted areas for weight and pace, and let the rule’s topic list widen the reading inside those areas. Merging the two lists into a single invented blueprint is the one preparation error this guide most specifically warns against.
For ladder contrast, the journeyman outline is 85 questions: Venting Regulations at journey level 20, Drainage Requirements 15, Water Distribution 10, Fixtures and Faucets 10, Plumbing Fundamentals 10, Traps and Interceptors 10, and Calculations 10, passed at 70 percent. The master paper adds Scope and Administration, raises Calculations from ten to fifteen, and raises the standard to 75 percent — the Board’s definition of the tier: same trade, deeper weight, added regulatory command, higher bar.
Passing at 75 percent, failing without a wait
Two layers state the master standard, and they agree. The bulletin headline states 75 percent to pass. The Board’s rule states that the applicant must have passed the examination by answering at least 75 percent of the questions correctly. Seventy-five percent is therefore the figure — verified twice over — displacing the journeyman’s 70 percent from the same bulletin and any generic standard remembered from another state. The Board’s general floor of at least 70 percent, unless otherwise specified, confirms the reading: the master 75 percent is the specification that otherwise applies.
Retake policy is where New Hampshire is most forgiving. For the journeyman and master examinations, there is no required waiting period between attempts; a candidate may retest as soon as an appointment is available. No attempt cap is stated in the verified record. A candidate cannot retake an examination once passed, unless the licensing authority requires it. Each attempt is a fresh $90 vendor fee. Cancellation and rescheduling are free online when done at least three days before the examination date; missing the appointment, or missing that deadline, forfeits the fee. Note the contrast inside the same bulletin: the First Year Plumbing Apprentice Bypass examination requires fresh Board approval before each attempt and a thirty-day wait after a failure. That discipline belongs to the Bypass examination only.
Forgiving is not free. A failed master sitting still costs the $90 fee, the preparation cycle that preceded it, and the working season during which business plans depending on a licensee of record wait. Failed candidates should use the immediate scoring to begin a targeted rebuild the same week.
Fees in their layers, and what is not charged
Licensing fees and examination fees travel to different offices and must never be blended. The examination fee is $90, paid to Prov at registration. The licensing fee is $330 under the Office’s fee table — a single combined application processing and licensing fee, the same for initial licensure, renewal, and reinstatement, buying a two-year license in each case. There is no separate application fee, no different renewal figure, and no reinstatement surcharge. No late-renewal fee exists in the verified record. Counted together, the layers total $420 — $90 to sit, $330 to license — each paid separately, at a different stage.
The neighbouring figures sit on the same combined basis: journeyman licensing $198, apprentice plumber $88, and the entity license $275 for two years for any number of employees. A master building a business should budget the entity figure alongside the individual one, because both licenses are required for the business to perform plumbing work.
Holding the license: term, education, supervision, reinstatement
The master license runs for two years from issuance — dated from the holder’s own issuance, not from a statewide common expiry. Renewal is the same $330 combined fee. Continuing education runs beneath the term: 6 hours per endorsement held per two-year cycle, earned in Board-approved seminars of at least three hours each, with no credit for repeating a seminar. The per-endorsement structure matters to masters who also hold fuel-gas endorsements, because the hours multiply by endorsement rather than by license. A circulating claim that New Hampshire requires no continuing education is false; the requirement is verified in the Board’s rules.
Supervision is the holding duty with daily consequences. A master may supervise apprentices subject to the statutory cap of no more than two apprentices per plumbing licensee. Apprentices work under direct supervision — the supervisor physically present, with telecommunication expressly not counting as presence — for the first two years, and thereafter under the broader defined supervision the rules describe. Two apprentices per licensee is a tight ceiling that shapes crew planning and hiring.
Reinstatement follows a one-year line. A license expired for one year or less is handled through the renewal process, with continuing education met, at the same $330 fee. A license expired more than a year requires initial licensure again. No surety bond is required for any plumbing credential in this family; the business entity must show liability insurance, with no minimum amount stated. Endorsement and reciprocity questions should be put to the Board in their proper layers — board agreements, statutory endorsement, and the examination route are three distinct mechanisms in the verified record, no state is named in any of them for this credential, and none should be blended into a promise of transfer.
A study plan built on the tested edition and the counted outline
Sequence the work by weight and by layer. First, edition discipline. Set up the 2018 code as the working book — permanently tabbed, pen-highlighted, organised under the bulletin’s reference rules — and set the adopted 2024 and concurrent 2021 editions aside, consulted only to mark differences. Every practice answer is a 2018 answer. Second, the counted heavy areas. Scope and Administration, Calculations, Venting Requirements, and Drainage Requirements carry sixty of the hundred questions; study time should follow that weight. Third, the supporting areas. Fundamentals, Traps and Interceptors, Water Distribution, and Fixtures and Faucets carry forty questions — enough to decide the sitting at the margin, and the natural source of the time surplus the heavy areas need. Fourth, the rule list inside the areas. Widen reading within the counted areas to the rule’s fourteen topics — plans and drawings read as interpretation, New Hampshire law, backflow, accessibility, commercial kitchen work, testing and disinfecting — without inventing counts for them. Fifth, integrated rehearsal. Full one-hundred-question sets inside 180 minutes, book open and organised, scored immediately, with every error sorted by kind: edition errors, lookup errors, calculation setup errors, and administration errors. Each kind has a different cure, and the final fortnight belongs to whichever kind is most frequent.
The errors this examination is built to catch
The New Hampshire master sitting catches layer errors above all. Studying the adopted code — 2024, or the concurrently electable 2021 — for an examination keyed to 2018 is the costliest error available, and diligent candidates make it most often, because the adopted book is the book on the truck. Reading a room-admission permission as edition-neutrality repeats the same error in miniature. Preparing to the journeyman outline and standard — no administration area, calculations at ten, 70 percent — underprepares every dimension the master tier adds. Merging the rule’s topic list with the bulletin’s counts invents a blueprint the Board never published. Arriving with an unprepared book — moveable tabs, loose notes, formulas written in — collides with reference rules enforced at the desk. Assuming no continuing education, a named reciprocity state, or a separate contractor license imports three verified falsehoods. And treating the no-wait retake as a strategy spends fees and seasons learning what one prepared sitting would have settled.
After the sitting: the licensee of record
Passing at 75 percent, with the result known at the desk, converts the journeyman into the individual through whom New Hampshire plumbing businesses are licensed. The master holds a two-year license, renewed at the same combined fee, educated at six hours per endorsement per cycle, supervising no more than two apprentices per licensee, and standing as licensee of record for an entity whose own license the firm must also hold. The examination’s design reads, from that destination, as a fair preview: administration and calculation weighted like system work, a tested code held distinct from the adopted code, and a standard set five points above the tier below. The companion New Hampshire Master Plumber Exam Preparation page describes the PassProfessor program built to that design.
Frequently asked questions
Who licenses master plumbers in New Hampshire?
The Mechanical Licensing Board, within the Office of Professional Licensure and Certification (OPLC), under RSA 153. There is no standalone board of plumbers.
Who delivers the master examination, and under what bulletin?
Prov, Inc., under the Board’s candidate information bulletin effective October 31, 2026. Board pre-approval is required before scheduling, and scoring is immediate.
Which code edition is tested, and which is adopted?
Tested: the International Plumbing Code 2018. Adopted: the International Plumbing Code 2024, effective July 1, 2026, with the 2021 edition in concurrence for permit applicants through December 31, 2026. From January 1, 2027, the 2024 codes govern all permit requests. The examination remains keyed to 2018.
How is the master examination structured?
A single-part, computer-based, multiple-choice examination of 100 questions in 180 minutes, open book, offered in English, at Prov testing centres — in New Hampshire, Concord at two sites, Nashua, and Newington — nationwide, or remotely.
What is the published content outline?
Plumbing Fundamentals 10; Scope and Administration 15; Calculations 15; Traps and Interceptors 10; Venting Requirements 15; Drainage Requirements 15; Water Distribution 10; Fixtures and Faucets 10.
What score passes the master examination?
75 percent, in both the bulletin and the Board’s rule. The journeyman standard is 70 percent.
What references may be used in the room?
The 2018 plumbing code and the Board’s administrative-rules document. Permanent tabs and pen highlighting are permitted; moveable tabs, sticky notes, in-exam marking, handwritten notes or formulas, and added documents are not.
Who is eligible for the master examination?
An applicant aged eighteen or older who has held a New Hampshire journeyman license for at least six months, shows good character and professional competence — including no consumer complaints resulting in disciplinary sanctions within the past year — and holds pre-approval.
Is there a practical or drawing-production component?
No. Reading plans and drawings, and system sizing and fixture calculations, are knowledge tested by multiple-choice questions, not work the candidate produces.
What are the verified fees?
Examination $90, paid to Prov. Licensing $330 — a single combined fee, the same for initial licensure, renewal, and reinstatement. There is no late-renewal fee.
How soon can a failed candidate retest?
As soon as an appointment is available — there is no required waiting period for the journeyman and master examinations. Each attempt carries a fresh $90 fee; rescheduling is free online at least three days before the date.
Is continuing education really required?
Yes. Six hours per endorsement held per two-year cycle, in Board-approved seminars of at least three hours, with no repeat credit.
How many apprentices may a master supervise?
No more than two per plumbing licensee, with direct supervision — the supervisor physically present — for the apprentice’s first two years.
What is the mechanical business entity license?
The firm credential under which a business performs plumbing work. It carries no examination and no continuing education, costs $275 for two years, and its licensee of record must be a master plumber. There is no separate contractor license.
Is PassProfessor affiliated with the Board?
No. PassProfessor is independent. The Board alone approves and licenses; Prov delivers the examination.
When does enrollment open for the PassProfessor program?
The program is in the works and enrollment is not yet open. Leave an email address on this page and PassProfessor will write to you when it is ready.
