Massachusetts Master Plumber Exam Guide: The State-Written Code, the Two-Part Closed-Book Sitting, and the Route Between Them

The Massachusetts Master Plumber license is issued under the Board of State Examiners of Plumbers and Gas Fitters, operating under M.G.L. c. 142 and 248 CMR inside the Division of Occupational Licensure. Massachusetts examines on 248 CMR 10.00, its own Uniform State Plumbing Code — state-written in 2023, adopting no model code. The examination is delivered by PSI, is entirely closed book, and is scored in two stand-alone parts: a candidate must reach a MINIMUM of 70% on each part. This guide works through the credential, the approval sequence, the published outline in full, the sitting itself, and the working rules of the license that follows. The companion program page is at /massachusetts-master-plumber-exam-prep/.

This program is part of the expanding PassProfessor catalog — join the notify list and we’ll email you when enrollment opens.

The credential at a glance

ItemVerified position
ProgramMassachusetts Master Plumber
RegulatorBoard of State Examiners of Plumbers and Gas Fitters (M.G.L. c. 142 + 248 CMR), housed in the Division of Occupational Licensure
Code examined248 CMR 10.00 — the Massachusetts Uniform State Plumbing Code, state-written, 2023 text; no model code is adopted or examined
Pre-approvalBoard pre-approval through eLIPSE required before scheduling; approval valid one year; allow three weeks processing
VendorPSI, retained to develop and administer the examinations, under the Board-written Candidate Information Bulletin dated 10/3/2025
Book statusClosed book — all parts; references are a study list only and are not allowed in the examination center
StructurePart I: 80 questions / 160 minutes. Part II: 40 questions / 160 minutes. Stand-alone part scores
Passing standardMINIMUM of 70% on each part
Part II characterLabelled “Practical” but computer-based; Isometric Analysis 20 of 40 questions; no hands-on component
RetakesMaster retakes unlimited; a failed part must be retaken within one year of the failure or all parts must be retaken; passing scores valid one year only
Official fees (closed set)Application $31; PSI examination $80; license on passing $78; renewal $78; late fee $57 after May 1 of even-numbered years
Continuing education12 hours per two-year license cycle for plumbers, with a Board-approved provider
Administrator notePassProfessor is independent and is not affiliated with the Board of State Examiners of Plumbers and Gas Fitters or the Division of Occupational Licensure

Massachusetts rewards candidates who read its system as a whole. The code is the Commonwealth’s own. The examination is closed book, so the code must be carried in memory rather than navigated on the day. The verdict is delivered part by part, so readiness must be measured part by part. And the license at the end of the route is a business-facing credential — the plumber with a regular place of business, employing journeymen, under a one-to-one supervision rule — so the eligibility and holding rules are not administrative decoration; they describe the structure the new master is about to stand at the centre of. The guide follows that whole shape.

Reading the verified facts

Massachusetts is unusually well published, and this guide uses that. The mechanics — counts, minutes, the pass standard in its published form, the fee set — come from the Board-written Candidate Information Bulletin dated 10/3/2025 and the Board’s own pages, and the two agree on the figures printed here. Two disciplines still apply. First, the passing standard is printed exactly as published — a MINIMUM of 70% on each part — and is never converted into a raw number of questions. Second, where the record carries a conflict, the guide follows the resolved position and says nothing of the other: the fuel gas amendments for NFPA 58 are cited at 248 CMR 8.00, the chapter the current Fuel Gas Code layer uses. What the record does not publish — a bulletin number, examination languages, the fee for an examination review — is not printed.

The route, step by step

Step one — complete the ladder below. The master candidate arrives as a licensed journeyman plumber. Beneath that license sit 6,800 hours as a licensed apprentice — under a master, or under a journeyman in a master’s employ — and 550 theory hours over at least four years, at no more than 165 hours a year, with a high school diploma or equivalent.

Step two — meet the master eligibility rule. Under 248 CMR 11.02(2): at least one year totaling at least 1,700 clock hours as a Massachusetts journeyman plumber actively engaged in installing, repairing and maintaining plumbing and gas fitting systems, and completion of the 110-hour Tier 5 of the five-tier Plumber Educational Program. If Tier 5 was completed as an apprentice, no additional education is required.

Step three — obtain Board approval through eLIPSE. Apply online only; mailed applications are returned. Allow three weeks for processing. Incomplete applications are held 180 days. Approval is valid one year — a window that should be treated as part of the study plan, not discovered inside it.

Step four — be scheduled by PSI. The Board notifies PSI of the approval; PSI notifies and schedules the candidate at one of its six Massachusetts centers: Auburn, Braintree, Boston/Charlestown, Fall River, Lawrence and West Springfield. Rescheduling without forfeiting the examination fee requires cancellation at least two days before the appointment.

Step five — sit both parts, closed book. Part I and Part II, each separately scored, each requiring a MINIMUM of 70% on each part. Scores are reported on site immediately. A failed part is retaken alone — within one year of the failure, or all parts must be retaken. Passing scores are valid one year only, so the license should be taken up promptly: the license fee on passing is $78, taken up through the eLIPSE profile.

Step six — hold the license. Biennial renewal at $78, due May 1 of even-numbered years, with a $57 late fee after that date; 12 hours of continuing education per two-year cycle; one-to-one apprentice supervision, with apprentices employed by a master only.

The code in depth: 248 CMR 10.00 and its companion layers

The tested reference list is a single list shared by all five of the Board’s bulletin examinations — there are no per-class lists — and studying it as a list is instructive. Its centre is 248 CMR 10.00 through 10.23, the Massachusetts Uniform State Plumbing Code in its 2023 text (current text effective December 8, 2023). Around it sit the Board’s regulatory chapters — 248 CMR 3.00, 4.00, 5.00 and 11.00 — covering the Board itself, the fuel gas code framework, gas fitting, and the licensing and examination rules this guide draws on. Then the fuel gas layer in its incorporated form: NFPA 54, 2012 edition, as modified by 248 CMR 5.00, and NFPA 58, 2011 edition with its errata, as modified by 248 CMR 8.00, together with the 2014 large gas utilization equipment provisions. Finally, the statute itself: M.G.L. c. 142.

Three consequences follow. First, Massachusetts does not examine on the IPC or the UPC as such, and 248 CMR 10.00 is not derived from either in any way a candidate can rely on — it is a state-written code, and it must be learned as one. Second, the fuel gas material is examined in its Massachusetts-modified form: the NFPA text as the Commonwealth’s chapters change it, which is why gas content carries such weight in the outline below. Third, the entire list is a study list. None of it enters the examination center. The closed-book condition converts every reference into a memory obligation, and the master’s obligation is the largest of any class because the master’s license will govern work performed by others under that same code.

The published outline in full

The bulletin publishes the master outline in full, and it is reproduced here in full because its weights are the most honest study plan available for this examination. One fact must accompany it: the master outline is identical, in areas and counts, to the journeyman outline in the same bulletin. The bulletin differentiates the two examinations through scope-of-work text and eligibility, not through the published content map, and no claim is made here — or should be believed elsewhere — that the master paper’s content map is different or harder. What is different is the candidate, the authorization, and the responsibility.

Part I — 80 questions. General Regulations, Inspections and Permits: 9. Gas Piping, Equipment and Appliances: 21. Venting: 12. Traps and Cleanouts: 2. Fixtures, Equipment and Clearances: 2. Water Heaters: 3. Piping, Valves and Controls: 3. Water Supply: 6. Hangers and Supports: 2. Drain, Waste and Vent: 13. Separators, Interceptors and Grease Traps: 5. Joints and Connections: 2.

Part II — 40 questions. Isometric Analysis: 20. General Trade Calculations: 5. Gas Piping: 7. Gas Venting: 8.

Read the weights as the Board’s own emphasis. Gas — piping, equipment, appliances and venting across both parts — is 48 of the 120 questions in the sitting, reflecting a license that authorises the master plumber to perform gas fitter work as well as plumbing work. Drainage, waste and venting with its associated venting block is the second centre. Isometric analysis alone equals the entire general regulations, water supply, separators and water heaters blocks of Part I combined — a quarter of the whole sitting turns on reading drawings well. The small blocks are not negligible: at two or three questions each, traps, fixtures, hangers and joints are exactly the blocks a candidate can lose a part by, in a system where each part must independently reach the standard.

The sitting itself

The sitting is computer-generated and computer-delivered, in a PSI center, under closed-book conditions. The admitted equipment is narrow: a non-programmable, non-printing, silent, battery-operated calculator without alphabet keys, and writing only on PSI-provided scrap paper. Nothing else — no code, no notes, no references — enters the room.

Part I runs 80 questions in 160 minutes: two minutes a question, a recall tempo. Part II runs 40 questions in the same 160 minutes: four minutes a question, a working tempo, because its dominant task is analysing isometric drawings rather than retrieving provisions. Scores are reported on site, immediately, part by part. A candidate who fails may review the missed items only immediately after the examination, before leaving the facility, within thirty minutes; the regulation separately allows written application to the Board’s designated exam administrator for a review, for a fee whose amount is not published and is not stated here.

Veterans should note the examination system’s own provision: a credit of five percent to each part, with the DD214 submitted with the application. Like the passing standard it adjusts, the credit applies part by part — there is no pooled score for it to attach to.

Retakes and the one-year rules in depth

For master candidates, the retake rule is stated in the bulletin in the plainest form in this catalog: there are no limitations on the number of times a candidate may take the exam. No master attempt cap appears in 248 CMR 11.02 either. Candidates arriving from material about the other Massachusetts examinations should set one rule aside firmly: the twelve-months-from-approval window with a six-attempt petition process applies to the journeyman, gas fitter and liquefied petroleum examinations — not to masters — and importing it into master planning understates the freedom and misstates the constraint.

The real master constraints are temporal. A failed portion must be retaken within one year from the date of failure, or the candidate must retake all parts. Passing scores are valid one year only. Board approval itself is valid one year. Three separate one-year clocks therefore run around a master candidacy, and managing them — sitting promptly after approval, retaking a failed part promptly, taking up the license promptly after passing — is part of passing in the administrative sense. No minimum wait between attempts is published, and none is stated here.

Fees in depth: the closed set

The master route’s official fees form a closed, corroborated set, and this guide prints that set and no other figures as the credential’s costs. Application: $31, non-refundable, paid through eLIPSE. Examination: $80 to PSI, the examination administration fee charged for every class, first attempt or retake, with retake fees non-refundable. License on passing: $78 for the Master Plumber, taken up through the eLIPSE profile — PSI does not issue the license at the center. Renewal: $78 on the biennial cycle, due May 1 of even-numbered years, with a late fee of $57 applying after May 1 for all classes. Candidates budgeting the full route should cost a retake at the same $80 examination fee, since the fee is per sitting; the application and approval sequence, once completed, is not repeated for retakes within the approval’s validity.

Holding the license in depth

The master license’s working rules explain why the eligibility rule demanded a year of journeyman practice inside Massachusetts. Supervision is one-to-one — not more than one apprentice under the direct supervision of a master or journeyman — and apprentices are employed by a master only, so every apprentice in the Commonwealth is, structurally, a master’s employee working under a master’s or a master’s journeyman’s eye. The master plumber’s scope, as the bulletin states it, is that of a plumber with a regular place of business who performs plumbing and gas fitting work subject to inspection, personally or through journeymen in his employ. The scope asymmetry with gas fitting runs in the plumber’s favour: a licensed master or journeyman plumber may perform gas fitter work; a gas fitter may not perform plumber work.

Continuing education is 12 hours per two-year license cycle for plumbers, journeyman and master alike, taken with a Board-approved provider in courses focused on 248 CMR, with documentation retained for at least three renewal cycles. The inspector regime — a different, annual figure for plumbing inspectors — is a separate system and is never blended with the licensee figure here. Out-of-state and international candidates proceed by petition on substantial equivalence; absent a reciprocity agreement, the relevant examination is still required, and no primary source names any state as holding such an agreement with Massachusetts.

A study plan built on how this examination is actually put together

Sequence by the outline’s weights and the parts’ separate verdicts. First, the code as memory — 248 CMR 10.00 learned for recall, not navigation, with every model-code habit explicitly checked against the Massachusetts text, because the closed-book room pays only for what is carried in. Second, gas, at its true weight — piping, equipment, appliances and venting in both parts, in the Massachusetts-modified NFPA form, until the largest block in the sitting is the candidate’s strongest. Third, drainage, waste and venting as the second centre, with venting studied across both its Part I block and its Part II return. Fourth, Part II as a separate discipline — isometric analysis practised at the four-minute tempo, with trade calculations, until the drawing paper is being performed rather than survived. Fifth, part-level measurement throughout — separate practice scores for Part I and Part II against the standard each must reach, because an averaged sense of readiness is the one number this examination does not use. Mixed timed practice closes the plan, alternating recall and drawing work inside single sessions, as the real candidacy will demand both within the same approval window.

The errors this examination is built to catch

Massachusetts catches predictable errors. Preparing for a practical that does not exist — expecting bench work in a computer-based Part II — wastes the preparation the isometric block demands. Averaging readiness across the parts hides the part that will fail, in a system with stand-alone scores. Trusting model-code memory on any provision the Commonwealth wrote differently fails silently, at two minutes a question, with no book to appeal to. Reading the master outline as a harder journeyman outline invents a difference the bulletin does not state and distorts study away from the published weights. Importing the six-attempt rule from the other examinations misstates the master’s actual position — unlimited attempts, bounded by one-year clocks. And letting a passing score age is the administrative version of failing: scores valid one year only must be converted into the license while they live.

Massachusetts in one view

Massachusetts in one view is a Commonwealth that wrote its own code and then examines on it from memory. The master candidate climbs a long ladder — 6,800 apprentice hours and five tiers of theory, the journeyman license, then 1,700 Massachusetts journeyman hours and Tier 5 — obtains the Board’s approval through eLIPSE, and sits a two-part, closed-book, computer-delivered examination through PSI in which gas work and drawing analysis carry the weight, each part must independently reach a MINIMUM of 70% on each part, and attempts are unlimited while time is not. The license that follows places its holder at the centre of a shop’s legal structure: employer of its apprentices, supervisor at a one-to-one ratio, the name behind its inspections, renewed biennially on twelve hours of code-focused education per cycle. The examination is the Commonwealth’s way of checking that the person about to carry that structure knows the code the structure runs on — its own code, carried in the head, produced under time. That is both the difficulty and the point.

After the sitting: the credential and its clocks

Once issued, the master license runs on the biennial clock: renewal at $78 by May 1 of even-numbered years, the $57 late fee beyond it, and twelve continuing education hours inside each two-year cycle with records kept across three. Its working duties run continuously beneath the cycle — supervision at one-to-one, the employment of apprentices, the inspections the business’s work is subject to — and the gas fitting authority that travels with the plumber’s license. The master who keeps the code current through the education cycle is maintaining the same asset the examination tested: a working command of 248 CMR, in the edition the Commonwealth currently publishes, applied to work the master answers for.

Frequently asked questions

Who writes the Massachusetts Master Plumber examination?

The Board of State Examiners of Plumbers and Gas Fitters writes the examination program; PSI is retained to develop and administer the examinations under the Board-written Candidate Information Bulletin dated 10/3/2025. Board approval through eLIPSE precedes scheduling.

What references is the examination based on?

A single list shared by all five bulletin examinations: 248 CMR 10.00–10.23 (2023); 248 CMR 3.00, 4.00, 5.00 and 11.00; NFPA 54 (2012); NFPA 58 (2011); and M.G.L. c. 142. The list is for study — no references are allowed in the examination center.

Is 248 CMR 10.00 based on the IPC or the UPC?

No. It is Massachusetts’ own state-written Uniform State Plumbing Code, current text effective December 8, 2023, adopting no model code. Massachusetts does not examine on the IPC or UPC as such.

What is the passing standard, exactly?

A MINIMUM of 70% on each part, in the bulletin’s published form. The regulation states the same standard as a score of no less than 70% on each portion. The parts are scored separately and never averaged.

How many questions are in each part, and how long is allowed?

Part I: 80 questions, 160 minutes. Part II: 40 questions, 160 minutes. Both parts are closed book and computer-delivered.

What is in Part II?

Isometric Analysis 20 questions, Gas Venting 8, Gas Piping 7 and General Trade Calculations 5. Part II is labelled “Practical” but is entirely computer-based; there is no hands-on component.

Is the master examination harder than the journeyman examination?

The bulletin publishes an outline for the master examination that is identical in areas and counts to the journeyman outline, and differentiates the two through scope-of-work text and eligibility. No different or harder master content map is published, and this guide claims none.

How many times can a master candidate test?

There are no limitations on the number of times a master candidate may take the exam. A failed part must be retaken within one year of the failure or all parts must be retaken, and passing scores are valid one year only.

What does the route cost in official fees?

Application $31; PSI examination $80 per sitting; license on passing $78; renewal $78 biennially; late fee $57 after May 1 of even-numbered years.

What continuing education is required?

12 hours per two-year license cycle for plumbers, with a Board-approved provider, in courses focused on 248 CMR, with documentation retained for at least three renewal cycles.

Can a master plumber do gas fitting work?

Yes. A licensed master or journeyman plumber may perform gas fitter work. The reverse does not hold: a gas fitter may not perform plumber work.

How many apprentices can work under one supervisor?

One. Not more than one apprentice may work under the direct supervision of a master or journeyman, and apprentices are employed by a master only.

Does Massachusetts reciprocate with other states?

No state is named in any primary source as holding a reciprocity agreement. Absent such an agreement, an out-of-state candidate petitions on substantial equivalence and the relevant examination is still required.

Is PassProfessor affiliated with the Board or PSI?

No. PassProfessor is an independent preparation provider. The Board alone licenses plumbers; PSI administers its examinations.

When does enrollment open for the PassProfessor program?

The program is in the works and enrollment is not yet open. Leave an email address on the companion program page, at /massachusetts-master-plumber-exam-prep/, and PassProfessor will write to you when the program is ready — and only about this program.