Wastewater Treatment Class II Exam Prep: Free Sample Questions — The Exact 20-Question Sample, Worked

These are the exact 20 questions served in the free sample of the Wastewater Treatment Class II Exam Prep program, in serve order, with the correct answer and a full explanation for each. The sample mixes easy, medium, hard, and stretch questions (5 / 7 / 5 / 3) drawn from this program’s own content areas.

THE PROGRAM IN NUMBERS
500
PRACTICE QUESTIONS
Fresh
FULL-LENGTH PRACTICE EXAMS
Drawn new for every attempt from the full question bank
Quick
QUICK PRACTICE
Short mini-quiz drills inside the course
20
FREE SAMPLE QUESTIONS
Try the program before you buy
6 months
OF ACCESS
Full access from the day you enroll

The 20 free sample questions

1. What is the primary purpose of jar testing in chemical dosing control?

A. To compare doses (and sometimes pH or mixing conditions) on bench samples so the plant dose is set from observed floc formation and settling

B. To measure the exact chemical purity of each delivery before it is accepted

C. To calibrate the chemical feed pump’s stroke counter against a stopwatch

D. To satisfy a paperwork requirement that has no effect on the dose actually fed, even when the same pattern has repeated over several operating shifts in a row

Correct: A. Jar testing lets the operator compare candidate doses on small samples and pick the one that performs, instead of guessing at full scale. The chosen dose is then verified against plant effluent results.

2. What is the purpose of periodically opening the end gates or flushing a trickling filter distributor arm?

A. To speed the arm permanently for better coverage as shown by comparing today’s readings with the unit’s normal range

B. To drain the filter media for inspection based on the inspection notes recorded at the last scheduled check

C. To clear solids settled inside the arm before they plug nozzles

D. To change the direction the arm rotates based on the readings logged over the past several operating shifts

Correct: C. Solids settle in the slow-moving water inside the distributor arm and migrate to the nozzles. Periodic flushing through the end gates removes that material before nozzle plugging distorts distribution.

3. During clarifier drive inspection, gear oil that has turned milky is an evaluation finding that most directly warns of what?

A. The drive is turning at the wrong speed according to the gauge readings taken during the most recent rounds

B. The scum skimmer is misaligned when checked against the performance baseline for this equipment

C. Normal break-in of new gear teeth under the loading conditions the unit has seen this operating week

D. Water has entered the gearbox and compromised the lubrication

Correct: D. Milky oil is emulsified with water, which degrades its ability to protect gear surfaces. Finding the water entry path and changing the oil prevents accelerated gear wear.

4. Which pair of operating characteristics distinguishes extended aeration from conventional activated sludge?

A. Short MCRT and a high F/M ratio

B. High-rate loading with minimal aeration time, without checking the operating trend data first

C. Long MCRT and a low F/M ratio, with extended aeration time

D. No wasting and no return sludge flow

Correct: C. Extended aeration operates with a long solids retention time and a low food-to-microorganism ratio. Its long aeration period suits small plants and package plants.

5. What role does alkalinity play in a nitrifying wastewater process?

A. It is the buffer that resists pH change while nitrification consumes it

B. It is the carbon source the denitrifiers use in the anoxic zone

C. It is the oxygen supply that keeps the aerobic zone from going septic

D. It is a coagulant that settles phosphorus out of the mixed liquor

Correct: A. Alkalinity is the water’s buffering capacity. Nitrification steadily consumes alkalinity, so when the reserve runs low the pH begins to fall and the nitrifying organisms are stressed.

6. During a load test, a generator’s voltage and frequency dip noticeably each time a large motor load is applied, then recover. What is being evaluated by this response?

A. The fuel tank’s venting capacity, because a restricted vent would starve the engine of fuel exactly when a large motor’s starting demand pulls the generator down

B. The battery charger’s output rating

C. The lubrication and contact condition inside the transfer switch, which must carry each new motor load cleanly or the generator will appear to falter as loads are added

D. The engine governor and voltage regulator’s ability to respond to sudden load changes

Correct: D. How far and how long voltage and frequency dip when load steps on measures the governor’s fuel response and the regulator’s correction together. Excessive sag means large motors may fail to start even though the generator carries steady load acceptably.

7. A secondary clarifier upset is sending extra solids out with the effluent. The WAS rate has not changed, but the calculated MCRT is falling. Why, and what wasting response follows?

A. MCRT counts only wasted solids, so the calculation must be an error and no response is needed

B. Solids leaving in the effluent raise MCRT, so wasting should be increased to balance it, so sludge age can be read from the wasting records alone

C. Solids leaving in the effluent count as removals just like WAS, so wasting should be reduced to compensate until the clarifier recovers

D. Effluent solids are returned by the RAS pumps, so they never affect sludge age

Correct: C. MCRT divides inventory by all solids leaving per day — waste sludge plus effluent solids. When effluent losses rise, total removals rise and sludge age falls unless WAS is trimmed to compensate.

8. A solids report lists total solids of 2,800 mg/L and volatile solids of 1,904 mg/L for digested sludge. What is the percent volatile solids?

A. 47%

B. 32%

C. 147%

D. 68%

Correct: D. Percent volatile = volatile solids divided by total solids, times 100: 1,904 / 2,800 x 100 = 68%. The report therefore shows 68% volatile solids.

9. Effluent chlorine residual is consistently zero, but dissolved oxygen sags in the receiving water just below the outfall and the dechlorination chemical usage is high. What adjustment fits these facts?

A. Increase the dechlorination feed further so no trace of chlorine can ever reach the stream, even when the same pattern has repeated over several operating shifts in a row

B. Stop dechlorination entirely for a week to see whether the oxygen sag goes away

C. Switch the dechlorination feed to run only at night, when the stream is not sampled

D. Trim the dechlorination feed down in small steps, checking that a small chlorine removal margin remains while the excess chemical feed stops

Correct: D. Excess dechlorination chemical consumes oxygen in the receiving water, matching the sag below the outfall with zero residual. Trimming the feed in small verified steps removes the residual without the oxygen-demanding excess.

10. A positive displacement blower delivers less air, its inlet vacuum reading is higher than normal, and discharge pressure is unchanged. What does the inlet vacuum evidence identify?

A. Diffusers are fouled throughout the basin under the loading conditions the unit has seen this operating week

B. A restriction at the inlet, most likely a loaded inlet filter

C. The discharge relief valve is stuck open based on the inspection notes recorded at the last scheduled check

D. The motor coupling is slipping under load under the operating conditions recorded during the current shift period

Correct: B. High inlet vacuum with reduced delivery localizes the restriction to the suction side of the blower. A loaded inlet filter is the usual cause and is confirmed by inspection and pressure recovery after service.

11. A clarifier drive’s shear pin has failed three times in two weeks. Each replacement pin was the correct part. What is the best evaluation and response?

A. Install a stronger pin so the drive stops interrupting service

B. Replace the pin with a bolt of the same diameter for a longer service life

C. Run the drive only at night when loads are lighter

D. Find and correct the real overload causing the failures

Correct: D. The shear pin is a protective device; repeated failures mean the drive is genuinely being overloaded. Defeating the protection risks major damage — the overload cause, whether solids accumulation or obstruction, must be found and corrected.

12. A plant bulks with confirmed filaments. The aeration outlet DO reads 2.1 mg/L, but profiling shows the first third of the basin at 0.3 mg/L for most of the day under load. Which adjustment targets the actual cause?

A. None, because the outlet DO proves oxygen is adequate

B. Redistribute aeration into the low-DO inlet zone

C. Reduce WAS to grow more filaments

D. Lower the RAS rate so the clarifier rests

Correct: B. A single outlet reading can hide a low-DO zone where most load is applied. Sustained very low DO in the inlet zone favors filaments, so aeration must be delivered where the demand is.

13. Phosphorus sampling shows strong phosphate release in the anaerobic zone, with phosphate much higher leaving that zone than entering it, yet final effluent phosphorus is also high. What does this profile indicate?

A. The anaerobic zone has failed completely, as shown by the absence of any measurable release across the zone

B. The laboratory phosphate test becomes invalid whenever release is strong, so the effluent value can be voided

C. Aerobic uptake downstream, since release is working

D. Too much nitrate is being recycled to the secondary clarifier, where it lifts solids over the effluent weirs

Correct: C. Biological phosphorus removal requires anaerobic release followed by aerobic luxury uptake; documented strong release with high effluent phosphorus places the limitation in the downstream uptake step.

14. Halfway through an analytical batch, the continuing calibration check reads well outside its expected range, although the checks at the start of the batch passed and sample duplicates agree closely. Which results are in question?

A. Only the single sample that was running when the check failed

B. No results, because the duplicates agreed with each other

C. The samples run since the last passing calibration check

D. The entire month of results produced by that instrument

Correct: C. Duplicates show precision, not accuracy. When a calibration check fails mid-batch, accuracy is unverified for everything analyzed since the last passing check, so that bracket of samples must be held and reanalyzed after recalibration.

15. A new elevated platform is built over an aeration basin, changing where operators stand and tie off. What must happen to the fall protection procedure before routine work begins from the platform?

A. Nothing, because the existing procedure already covers every elevated surface at the plant

B. The platform is added to a list for review at the next annual procedure revision only

C. Operators are told to use extra care for the first month while the procedure catches up later

D. The procedure is reviewed and updated for the new access, guarding, and anchorage conditions, and affected operators are briefed

Correct: D. Safety procedures must match the workplace as it actually exists. A new work position changes access and anchorage, so the procedure is updated and the affected operators are briefed before routine work starts there.

16. A trickling filter keeps ponding even after excess surface growth is flushed off and distribution is verified even. Ventilation through the bed seems poor. What deeper equipment condition should be evaluated?

A. The effluent launder level in the following clarifier as shown by comparing today’s readings with the unit’s normal range

B. The chlorine demand of the filter effluent based on the inspection notes recorded at the last scheduled check

C. Plugged or damaged underdrains restricting drainage and airflow

D. The speed of the distributor at night flows based on the readings logged over the past several operating shifts

Correct: C. Ponding that survives surface cleaning and even distribution means water cannot leave the bed freely, which points to the underdrain system. Blocked underdrains also choke the natural draft ventilation the biomass depends on.

17. A vacuum-operated chlorinator shows normal vacuum at the injector, the supply indication is normal, but no chlorine feeds and the rotameter float sits at zero. Where does the evidence direct the check?

A. Between the vacuum source and the gas path, checking for a closed valve or blocked line

B. To the injector water supply, because loss of injector flow is the usual cause of no feed

C. To the contact basin baffles, because poor baffling can make feed appear to be zero at the unit

D. To the residual analyzer, because a failed analyzer closes the chlorinator feed valve fully

Correct: A. Vacuum present at the unit but zero gas flow separates the vacuum system, which is working, from the gas path, which is interrupted. A closed valve, a blocked line, or a stuck regulator component between supply and rotameter is where the evidence leads.

18. Reviewing the safety equipment log, a supervisor finds eyewash flushing checks were signed off for three weeks when the assigned operator was on leave. What is the best response?

A. Flush and verify the eyewashes now, assign and document a backup checker, and address the false sign-offs with the crew

B. Initial the missing weeks personally so the inspection log appears complete and consistent when it is reviewed later

C. Reduce the flushing schedule to once a year so the documented practice matches what actually happened during the leave

D. Remove the eyewashes from the safety checklist altogether, since no eye injury occurred during the weeks in question

Correct: A. The immediate need is verifying the equipment actually works; the program fix assigns a backup checker, and false sign-offs are addressed directly because readiness records must reflect real checks.

19. Clumps of sludge rise to the clarifier surface and float over the weirs late in the day. SVI is 98 mL/g, the microscope shows few filaments, gas bubbles are visible in the rising clumps, and the blanket has been held deep. What is happening and what helps first?

A. Filamentous bulking; hunt for a nutrient deficiency, without checking the operating trend data first

B. Pin floc; waste more solids

C. Denitrification in the clarifier; increase RAS to shorten blanket time

D. Dispersed growth; waste less solids

Correct: C. Gas bubbles in rising solids with normal SVI and few filaments indicate nitrogen gas from denitrification in a long-held blanket. Returning solids faster and thinning the blanket shorten its detention in the clarifier.

20. A tertiary filter’s filtrate turbidity sits just above the plant’s target even with effective backwashing and reasonable run lengths, and the operator is considering a small coagulant dose ahead of the filter. What is the best way to evaluate that idea?

A. Set the coagulant dose at the highest the feed pump can deliver and judge by the next day’s results, and then return the unit to full service right away

B. Bench-test the coagulant aid at a few doses and compare filtrate quality, then trial the best dose and verify against the target before adopting it

C. Skip testing, because chemical aid ahead of a filter never changes capture

D. Judge the idea only by whether backwash frequency changes

Correct: B. A small coagulant dose can help a filter capture fine solids that pass through on their own, but the dose has to come from observed bench results and be confirmed at full scale. Guessing at a maximum dose risks overdosing and shortening runs.

Take the sample as a timed quiz in the full program: open the free sample quiz. The full program carries 500 questions with an explanation for every answer — enroll for $49 with 6 months of access. See also the Wastewater Treatment Class II exam guide.

Disclaimer

PassProfessor is an independent exam-preparation provider. This program is exam preparation only: it is not the real exam, it provides no education credit, and completing it does not by itself qualify you for any license or certification. The real exam is run by its own exam body — you register for it, pay its fees, and sit it through that body, not through PassProfessor. All practice questions in this program are original; they are not actual exam questions.